PHANTEKS AMP GH Gold ATX Power Supply Modular Installation Guide
- July 30, 2024
- PHANTEKS
Table of Contents
INSTALLATION GUIDE SUPPORTS
PH-P650GH_01
PH-P750GH_01
PH-P850GH_01
PH-P1000GH_01
PH-P1200GH_01
PH-P1300GH_01
ACCESSORIES INCLUDED
Accessories Included
User Manual
Installation Guide
PSU Bag
Cable Bag
Ziptie Bag
Screw Pack
| POWER SUPPLY AMP GH | MANUAL WARRANTY | CABLE BAG |
|---|---|---|
| ZIP TIE BAG | SCREW PACK | |
CABLES INCLUDED
MOTHERBOARD 24-PIN| CPU 4+4-PIN| 12V-2X6 12+4-PIN| C13 POWER
CABLE
---|---|---|---
| | |
PCIe 6+2-PIN| SATA| SATA | MOLEX
| |
Cable Type| Connectors per Cable| Length per Cable (mm)
---|---|---
Motherboard 24-PIN| 1| 610
CPU EPS 4+4-PIN| 1| 650
PCIe 6+2-PIN| 1| 750
12V-2×6 12+4-PIN| 1| 720
SATA| 4| 450 – 150 | 150 | 150
SATA | Molex| 2 | 2| 450 – 150 | 150 | 150
C13 Power Cable| 1| 1500
- The amount of cables may vary depending on model.
01 INSTALL PSU INTO CHASSIS
Secure the power supply with the 4x included PSU screws. Check the PC chassis manual for more installation details.
INSTALL
PSU SCREW 4x
PRO TIP
Pre-connect all needed cables to the PSU before installing it into the
chassis. See step 2
02 CONNECT CABLES TO PSU
Connect all needed cables to the power supply according to the overview below. The exact connector lay-out and quantity may be different depending on the model.
-
12V-2X6
12+4-PIN -
CPU | PCIe
8-PIN -
SATA | MOLEX
6-PIN -
MOTHERBOARD
10+18-PIN
- Connectors may vary depending on model.
03 CONNECT CABLES TO SYSTEM COMPONENTS
Connect all power cables to the corresponding system components, please follow the manufacturers instructions for additional information.
| |
---|---|---
MOTHERBOARD 24-PIN| CPU 4+4-PIN| PCIe6+2-PIN
| |
SATA| MOLEX| 12V-2X6 12+4-PIN
- The amount of cables may vary depending on model.
04 12V-2X6 GPU CONNECTOR
The AMP GH is equipped with the 12V-2×6 PCIe Gen5.1 GPU connector and cable. Note that a compatible GPU is required.
The maximum power output depends on your AMP GH model:
12V-2X6 12+4-PIN CABLE
| AMP Model | Output Watts |
|---|---|
| GH 1200 | Up to 600 |
| GH 1000 | Up to 600 |
| GH 850 | Up to 450 |
| GH 750 | Up to 450 |
| GH 650 | Not available |
05 CONNECT POWER CABLE
Connect the power cable to the power supply and a grounded power outlet respectively. Make sure the power supply is turned off ‘ O ’ before connecting it to a power outlet.
06 HYBRID FAN MODE
Use the Hybrid Fan Mode to unlock the 0RPM fan speed when under 30% load. This will make the power supply absolutely silent under low load and temperature levels.
Hybrid Fan Mode is turned on when the button is pressed in, and off when pressed again.
07 BE SAFE!
Switch the power button to the ‘ I ’ position to turn on your system.
When making any changes to the hardware, be sure that the power button is switched from the ‘ I ’ to the ‘ O ’ position so the power supply is turned off.
Only use Phanteks cables that are provided with the power supply. If there are any questions, please don’t hesitate to visit www.phanteks.com/FAQ for more details.
Phanteks will not take responsibility for any damages incurred due to incorrect installation or usage of this product.
FOLLOW US ON
SOCIAL MEDIA
Instagram
Phanteks
Facebook
Phanteks
YouTube
Phanteks
Twitter
@phanteks
SUPPORT
US & Canada
support@phanteksusa.com
International
support@phanteks.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>