Contour CDSMPRO20310 SliderMouse Pro Wired User Guide
- June 12, 2024
- contour
Table of Contents
Contour CDSMPRO20310 SliderMouse Pro Wired
What’s in the Box?
- SliderMouse Pro
- Wrist rest
- Keyboard Risers
- USB charging cable (mounted)
Functions
A. Cursor speed
B. Power switch (no function for wired unit)
C. Navigation bar
D. Copy
E. Paste
F. Left-click
G. Right-click
H. Scroll wheel
I. Double-click
Connection
Connect the USB cable from your SliderMouse into an available USB port on your
computer. Your computer will recognize your new device and connect
automatically.
Cursor Speed (DPI)
Press the Cursor speed (button A) to cycle through cursor speeds. There are
speed selections which range from slow (600 DPI) to fast (2800 DPI). Speed can
be identified by the LED lights as shown. Hold Cursor speed (button A) for 8
seconds to default settings.
Navigation bar click force adjustment
Click force refers to the level of resistance when clicking the navigation
bar. To adjust click force, press and hold both button A (Cursor speed) and
button F (Left-click) for two seconds, the LED light will show the current
click force setting. While continuing to hold button A, release button F and
use button H (scroll wheel) to change click force settings. Release button A
to select click force.
To disable the navigation bar click function, adjust the click tension until
all LEDs are illuminated.
Navigation bar click volume adjustment
The navigation bar has 6 different click volume settings. To change the click
volume, press and hold button A (Cursor speed) and button G (Right-click) for
two seconds, the LED light will show the current click volume setting. To
adjust click volume continue to hold button A and release button G, then move
button H (Scroll wheel) up/down to adjust the click volumen. Release button A
to confirm.
To disable the navigation bar click volume, adjust the click volume until alle
LEDs are illuminated.
Keyboard risers
Before using your SliderMouse Pro, please take a moment to adjust your
keyboard.
If you are using other keyboards than Contour’s Balance Keyboard, you can use
the Keyboard risers to achieve the desired keyboard height and angle. Simply
place the Keyboard risers under your keyboards feet – as the keyboard was
lying on the table.
For a proper ergonomic position the front edge of the the keyboard should be as close to the Navigation bar as possible. We recommend to use negative tilt helping you to hold a neutral wrist position and decreasing the extension of your fingers.
Software driver
All Contour’s ergonomic products are plug-and-play. If you want to customize
your SliderMouse Pro, we recommend to download the free driver available at:
contourdesign.com/drivers
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
IC Statement
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
1. This device may not cause interference; and
2. This device must accept any interference, including interference that may
cause undesired operation of the device.
The term “IC:“ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications.
Warranty
If there is a functional defect due to faulty manufacturing, we will replace
the product. This warranty does not cover damage that results from misuse of
the product.
Attention!
If you attempt to dismantle your “SliderMouse Pro” you will invalidate your
warranty.
Contour Design Nordic A/S Nyropsgade 41-43, 1. floor
DK-1602 Copenhagen V, Denmark Phone: +45 70 27 02 27
Email: info@contourdesign.com
Contour Design, Inc.
10 Industrial Drive
Windham, New Hampshire 03087, USA Phone:
603-893-4556
Email: ergoinfo@contourdesign.com
For more information please visit:
www.contourdesign.com
Tested to comply with FCC and IC standards.
References
- Drivers – Download Software for Contour Design Products
- Contour Design – Ergonomic mice, Superior design
- Contour Design – Ergonomic mice, Superior design
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>