tuya JXJ-FA02 WIFI Battery Camera Instruction Manual
- June 1, 2024
- Tuya
Table of Contents
tuya JXJ-FA02 WIFI Battery Camera
Specifications :
- Resolution : 720X1280, 1920X1080
- Video bit rate: Adaptive
- Support capacity: Up to 128G
- Audio: Built-in speaker & Microphone
- WiFi Mode: 2.4GHz 802.11n/g/n
- Power Supply: DC 5V
- Battery: Rechargeable Battery
- Motion Detection: PIR Sensor
- Recording method: SD Memory Card/Cloud Storage
- Power consumption: Standby 200uA, Working 260mA
Product Usage:
-
Setup and Installation:
Follow these steps to set up the WIFI BATTERY CAMERA: -
Place the camera in the desired location.
-
Ensure the camera is connected to a power source.
-
Download and install the TuyaSmart app by scanning the QR code or searching for it in the app store.
-
Register and log in to the app to add the device.
-
Connecting to WiFi:
Make sure your phone and router are connected to a 2.4GHz WiFi network before adding the camera to the app. -
Viewing and Settings:
You can view and adjust settings through the TuyaSmart app after successfully adding the camera.
FAQ:
-
Q: What type of WiFi does the camera support?
A: The camera only supports 2.4GHz WiFi networks and does not support 5GHz networks. -
Q: How can I reset the camera?
A: Press and hold the reset button for 5 seconds to reset the camera. -
Q: How do I know if the camera is connected to the network?
A: Check the indicator lights on the camera for network connection status. -
Q: What is the maximum storage capacity supported?
A: The camera supports SD cards up to 128GB for storage.
Instruction Manual
WIFI BATTERY CAMERA
Product categories
Technical Parameters
- Resolution: 720X1280 1920X1080
- Video bit rate : adaptive
- Viewing angle: 135-165°
- Support capacity : Up to 128G
- Audio: Built-in speaker & Microphone
- WiFi Mode: 2.4GHz 802.11n/g/n
- Power Supply : DC 5V
- Battery: Rechargeable Battery Motion
- Detection : PIR Sensor
- Recording method : SD Memory Card/ Cloud Storage
- Power consumption : Standby 200uA, Working 260mA
APP Download & Installation
- Quick download APP by scanning QR Code as following.
- Search for ‘TuyaSmart ‘ app in App Store(for IOS)/App Market, or scan the above QR code to download.
- This camera only support 2.4G WiFi, not support 5G WiFi router and please make sure,the phone and router Network is 2.4 G WiFi connection
- To ensure the normal use of the APP function, when installing “TuyaSmart” APP, please allow and open the APP all permissions!
Register and log in
-
Open the APP, if you haven’t account, click on the “Sign Up” (figure 1), enter the registration screen, enter a phone number registered account. Registration is completed, then login APP.
-
After login the APP, can be directly select “add device” or choose to create family after add, create family methods: APP at the bottom right corner click on “my” choice “family management”, “my home” fill in the information & save (figure 2).
-
Add Device
In APP Home page, click on the “Add Device” or upper right “+”, you car choose ” Add Manually” (figure 3), select ‘Security& Video Surveillance- -Smart Camera(Wi-Fi) “(figure 4) to add equipment
-
Please make sure the camera in distribution network model (status indicator light red light flash) (figure. 5) Choose “Make sure the indicator is flashing quickly or a prompt tone is heard” click “Next. enter phone connected WiFi password(figure 6) , click next
-
APP appear QR Code distribution network guide interface, aim the QR Code camera lens about 15cm to 20cm (figure 7) when hearing Prompt, click on the “I Heard a Prompt”, enter the next step; Equipment began to connect to the server, please wait until the complete distribution network. (figure 8)
-
(figure 9) page, that device has been added successfully. Here you can name for this device
-
View & Setting
Click device, enter the camera preview control interface (figure 10), interface display picture, for clarity and full screen switch operations and, at the bottom of the menu can provide photos, intercom, video playback, alarm Settings, pendant, direction and so on. Click upper right Setting button, and enter the Settings interface (as shown in figure 11), you can set the camera to share, the basic function, and so on.
FAQ
-
Q:How to share the device ?
A:In real-time video viewing screen, click the top right corner device button to enter setup interface, click the “share equipment”, then click “add device”, sharing by entering mobile number or email address, click “finish”, sharing success -
Q:How to check camera abnormal offline?
- A: Check the power supply and the network if it is normal
- Restart the device
- Configure the camera
- Check whether the home broadband is normal
Device prompt and indicator condition
Fcc Warning
This device complies with part 15 of the FCC Rules,
Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- his device must accept any interference received, including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
- If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum 20cm distance between the radiator and your body: Use only the supplied antenna.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>