PHANTEKS GLACIER ONE 240 T30 User Manual
- June 6, 2024
- PHANTEKS
Table of Contents
PHANTEKS GLACIER ONE 240 T30
Package Contents
- Infinity Mirror Cap
- 240×38 mm Radiator
- 2x 120mm T30 Fans
Accessories
T30 Fan preparation
The T30 fan supports 3 different fan profiles via a switch on the fan hub.
Please choose your preferred fan profile before installing the fan into your
system. We recommend the default ‘Performance mode’. 
Motherboard preparation
AMD Socket AM4
A) Remove the stock mounting brackets.
B) Secure the 4x AM4 Stand-offs to the motherboard. 
INTEL Socket 115X / 1200 / 1366
A) Prepare the Intel Backplate for the correct socket.
B) Secure the 4x 115x/1200/1366 Stand-offs to the motherboard and Intel
Backplate.
INTEL Socket 2011 & 2066
A) Secure the 4x Intel 2011/2066 Stand-offs to the motherboard 
Installing the pump block
A) This step is for AMD AM4 socket only (for Intel socket installation, go to step 3B)
Remove the Intel bracket from the pump
- Push the Intel bracket in
- Rotate to loosen
- pull the bracket off
- push the AMD bracket in
- rotate to fasten the bracket
B) Secure the pump unit to the stand-offs on the motherboard with the 4x
Thumb Nuts
The thermal compound is pre-applied. More thermal compound is included for future installations.
Mount the radiator and fans
We recommend to install the fans to the radiator before mounting it into the chassis. 3 Types of screws are included to mount the radiator and the fans in different options:
- Use the 5mm radiator screw to mount the radiator directly to the chassis
- Use the 36mm fan screw to mount the fan to the radiator (and chassis)
- Use the 39mm Halos screw to mount the Halos and fans to the radiator (and chassis)
- Use the optional washers if necessary on the chassis for a secure fit
Option A:
Option C (When using Halos only):
Install Infinity Mirror Cap and Tube Clips
A) The Infinity Mirror Cap simply snaps into place via strong magnets.
Make sure the D-RGB cable stays clear from the Thumb Nut.
B) OPTIONAL: Install the (3x) included Tube Clips for a tidy tube routing. Simply snap the clips on the tubes.
Fan cables can be routed through the middle of the Tube Clips.
Connect cables
Pump & Fan cables
A) Connect the Fans together with the Daisy-chain cables and use the Fan
PWM Extension Cable to reach the motherboard.
Choose between 2 configurations:
B1) Use the PWM Splitter Cable to connect the pump and fans to a single
motherboard CPU header.
B2) If 2x CPU headers are available on the motherboard, the pump and fans can also be connected individually (without PWM Splitter Cable) for more precise control.
D-RGB cable connection
The D-RGB lighting can be controlled through a D-RGB equipped Phanteks chassis/controller or motherboard.
A) To Phanteks D-RGB Chassis/Controller Connect the chassis D-RGB
connector to the Infinity Mirror Cap and/or Halos.
B) To D-RGB Motherboard
Use the 3-Pin D-RGB Motherboard Adapter to connect the D-RGB cable to a D-RGB
equipped motherboard (A-RGB*).
To D-RGB Lighting Products
All Phanteks D-RGB lighting products can be daisy-chained together.
Support & Warranty
As a Phanteks customer, you are priority number one. We have a dedicated team of employees across the globe to deliver the experience you deserve.
CUSTOMER CARE
RMA AND TECHNICAL SUPPORT AMERICAS
Hours : Monday-Friday 9:00-5:00 PST
Phone number : +1(909)598-2115
Email :support@phanteksusa.com
Facebook : @Phanteks
RMA AND TECHNICAL SUPPORT INTERNATIONAL
Email : support@phanteks.com
Facebook : @Phanteks
For spare parts and optional upgrades please visit: www.axpertec.com (EU) | www.phanteksusa.com (US)