eta Roger Hair and Beard Trimmer Instruction Manual

eta Roger Hair and Beard Trimmer

Product Information

Specifications:

• Brand: Roger
• Model: eta 9345
• Power Input: 100-240 V (AC) 50/60 Hz
• Power Output: 5.0 V (DC) 1.0 A 5.0 W
• Weight: 0.3 kg

Product Usage Instructions

Safety Warning
Before operating the appliance, carefully read and understand all safety warnings provided in the user manual.

Description of the Appliance and Its Accessories
Prior to using the appliance, ensure that the batteries are fully charged. The operation time per charge varies based on the attachment used and workload, typically around 40 minutes.

Instructions for Use

1. Make sure the Clipper is turned OFF before charging.
2. Choose the charging method (directly through the adapter or using the charging stand).
3. Connect the adapter to a power source and monitor the battery charge status on display A2 during charging.
4. Allow approximately 2 hours for a full charge but do not exceed the recommended charging time.
5. After charging is complete, disconnect the adapter from the mains and then unplug it from the appliance.
6. Ensure the battery is fully charged (display shows 100) before use.
7. Select the desired cutting speed setting (5500, 6000, 6500, 7000 RPM) using the A8 cutting speed indicator on the trimmer display.
8. For initial use, start with an attachment of maximum length to avoid a very shortcut. Subsequently, use attachments with lower lengths as needed.

FAQ:

• Q: How long does it take to fully charge the Clipper?
  A: It will take approximately 2 hours to fully charge the Clipper. Ensure not to exceed the set charging time.

• Q: What is the battery life indicator during charging?
  A: The battery charge status is displayed on indicator A10, showing percentage values ​​and remaining battery life.

• Q: How can I select different cutting speeds?
  A: You can choose from four different cutting speed settings (5500, 6000, 6500, 7000 RPM) using the A8 cutting speed indicator on the trimmer display.

INSTRUCTIONS FOR USE
Dear customer, thank you for purchasing our product. Please read the operating instructions carefully before putting the appliance into operation and keep these instructions including the receipt and, if possible, the box with the internal packing

SAFETY WARNING

• Before the first use, read the instructions for use carefully, look at the picture and keep the instructions for use.
• Check whether the data on the type label corresponds with the voltage in your socket.
• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
• Before replacing accessories or accessible parts, which move during operation, before assembly and disassembly, before cleaning or maintenance, turn off the appliance and disconnect it from the mains by pulling the charger from the power socket!
• Do not leave the iron plugged in power supply without supervision!
• If the power cord of the charger is corrupted, it has to be replaced by the manufacturer, its service technician or a similarly qualified person so as to prevent dangerous situations.
• Never use the appliance if its power cord or charger is damaged, if it does not work properly, if it fell down and was damaged and it is leaking. In this case take the appliance to a special service to check its safety and proper function.
• For additional protection we recommend installation of current protection (RCD) with the nominal release current not exceeding 30 mA. Ask a control technician or an electrician for advice.
• The trimmer with the plugged adapter must not be used at places where it could fall into a bathtub, a wash basin or a swimming pool. If the trimmer fell to water anyway, do not take it out! First of all, unplug the adapter from the socket and only then remove the trimmer. In this case take the appliance to a special service to check its safety and proper function.
• Always unplug the appliance from charger if you leave it unattended.
• The appliance is intended for use in households only and for similar use! It is not designed for use in hair salons or for other commercial use!
• Do not put or take out the plug to or from a socket with wet hands!
• Never immerse the appliance or the adaptor in water or other liquids (not even partly) and never wash in running water!
• Use only the accessories designed for this type. Do not use damaged adapters.
• Never tuck the appliance or the accessories into anybody holes.
• Be careful in using the appliance without a set adapter, the blades are sharp.
• Do not use the appliance while having a bath, having a shower or taking a sauna and for trimming wet or artificial hair.
• The appliance is not intended for operation with an exterior time switch or separate remote control system.
• The appliance is not intended for styling animal hairs.
• Never charge the appliance in direct sunlight or close to heat sources and if the temperature is below 10 °C or above 40 °C. If the appliance is fully loaded, unplug the charging device.
• In case the cutting lath gets blocked, the appliance must be turned off immediately and the cause removed.
• The appliance gets hot when charging which is absolutely normal.
• Charge the battery in a temperature close to room temperature.
• Do not dispose the battery into fire. There is a risk of explosion!
• Do not charge a battery which is leaking electrolytes.
• Do not expose the battery to temperatures higher than 50 °C to prevent damaging the battery.
• Do not put the trimmer on hot heat sources (e. g. oven, stove, radiator, etc.)
• Also, do not put the trimmer in the on position on soft surfaces (e. g. bed, towels, sheets, carpet); the surfaces or the appliance could get damaged.
• The power cord of the adapter must not be damaged with sharp or hot objects, open fire and it must not be sunk into water.
• The adaptor supplied with this appliance is intended for this appliance only, do not use it for other purposes. Also, use only the supplied adaptor with this appliance, do not use any other adaptor for charging (e.g. from another appliance).
• Never use the appliance for any other purpose than for the intended purpose described in these instructions for use!
• During normal operation, the accumulator batteries are not taken out. Take out the batteries only if the appliance is to be disposed of (see par. ENVIRONMENTAL PROTECTION).
• The producer is not responsible for any loss caused by improper handling of the appliance and its accessories (e. g. injury, appliance damage, fire, etc.) in the case of non-compliance with the safety instructions above.

DESCRIPTION

DESCRIPTION OF THE APPLIANCE AND ITS ACCESSORIES (fig. 1)

• A – trimmer
  • A1 – switch button (on/off)
  • A2 – display
  • A3 – trimming head
  • A4 – blades
  • A5 – blade cut length switch (1 / 1.3 / 1.6 / 1.9 mm)
  • A6 – socket for charging
  • A7 – change speed buttons (+ / –)
  • A8 – cutting speed (K. RPM.)
  • A9 – leftover battery indicator (%)
  • A10 – charge / battery indicator
• B – attachments
  • B1 – comb attachment (4–6 mm)
  • B2 – comb attachment (7–9 mm)
  • B3 – comb attachment (10–12 mm)
  • B4 – comb attachment (16–18 mm)
  • B5 – comb attachment (22–24 mm)
  • B6 – comb attachment (28–30 mm)
  • B7 – Thin-out
• C – attachment
  • C1 – charging adapter
  • C2 – brush
  • C3 – blade lubrication oil
  • C4 – travel case
  • C5 – charging adapter

INSTRUCTIONS FOR USE

Before you can use the appliance, its batteries must be charged. The operation time for one charge depends on the attachment used and workload. Attachment is around 40 minutes.

To Charge/Recharge

• Fully charge Clipper before using for the first time or after non- use for a long period of time.
• Battery performance is best if you recharge only when the battery is (almost) completely empty.
• Continuously recharging Clipper will reduce lifespan of battery.

1. Be certain Clipper is OFF.

2. Select charging method (directly through the adapter or with the use of the charging stand).
   Then connect the adapter to power.

3. The battery charge status is shown on the display A2 during charging (when the A10 charging indicator switches on and the battery life is changing „AVAILABLETIME“ A9 in %). When fully charged, the displayed values become steady, the indicator switches off and the average battery life in %, which corresponds with the cutting speed, remains visible (RPM).

4. It will take approximately 2 hours to fully charge the Clipper. Do not exceed the set time of charging!

5. After charging, unplug the adaptor from the mains first and only then unplug the connector from the appliance.

Notes
During charging, the value shown on the display increases in increments of 1 %.
When charging is completed, the display shows “100”.

Optimize the working life of the battery

• Do not charge for more than 2 hours.
• Do not keep cord permanently plugged in.
• Discharge / run down the battery completely twice a year by letting the motor run until it stops.

Let the battery charge fully afterwards.

Use
The trimmer can be used without the adapter (for cutting contours) or with the selected adapter B1–B7 according to the required cut length. Put the attachment on the head of the appliance, so that it locks in place (see fig. 1). Proceed reversely when taking the attachments off. The trimmer can be operated from the outlet with the adaptor connected or only from the charged battery.

Controls

• Turn on the trimmer – if it is off, shortly press the A1 button.
• Change the trimming speed – shortly press the A7 (+ / –) button when in operation.
• Turn off the trimmer – shortly press the A1 button.

There are 4 different cutting speed settings in thousand revolutions per minute (5500, 6000, 6500, 7000 RPM). indicated (the A8 cutting speed indicator) on the trimmer display.

Hair clipping

• The trimmer turns on and off with a switch A1. Turn the trimmer on only after all the attachments have been properly placed and you are ready for trimming. Turn the trimmer off immediately after use.
• We recommend oiling the blades with the oil C3 attached before first use.
• Before you start clipping, make sure that the head of the person whose hair you are cutting is at the same level as your chest so that all parts of his/ her head are clearly visible and within easy reach.
• Only use the clipper on dry hair.
• Do not use on freshly washed hair.
• Before you begin, comb the hair in the direction of growth.
• To achieve optimal clipping results, always move the clipper slowly through the hair against the direction of hair growth.
• In case an blade A4 gets blocked, the appliance must be turned off immediately and the cause of the block removed.

Clipping with hair comb attachment
You may use 7 kinds of comb attachments B for trimming,

1. Put on the desired comb attachment (B1–B7). Then you can turn on the appliance.
2. If you are trimming for the first time, begin by trimming with an attachment of max. length to prevent too short of a cut. When you have familiarized yourself with the settings, use attachments B with lower length.
3. You may also use the blade cut length switch A5 for finer cut setting.
4. Make sure that the flat part of the comb is always in full contact with the scalp to obtain an even result.
5. Move the clipper slowly over the crown from different directions to achieve an even result.
6. Always move the clipper against the direction of hair growth.
7. Make overlapping passes over the head to ensure that all hair that should be cut has been cut.
8. Turn the Clipper off and remove the hair comb often to blow and/or shake out hair that has accumulated.

Contouring without the hair clipping comb attachment

1. Remove the hair comb (if it is attached). Be careful when you are clipping without comb attachment as when the clipper is turned on it will trim every hair it touches.
2. Tilt the clipper in such a way that only one edge of the trimming attachment touches the hair ends when you shape the contours around the ears.
3. To contour the nape of the neck or hairline, turn the clipper and hold it with the trimming attachment pointing downwards.
4. To contour the sideburns, turn the clipper and hold it with the trimming attachment pointing downwards.
   Note You may also use the blade cut length switch A5 for finer cut setting.

Trimming facial hair

1. Mark a facial hairline with the trimmer and cut off the hairs exceeding this line from the outer perimeter
2. If you want to achieve an even trim of facial hair, use one of attachment B or trim carefully the ends by small pieces over the brush in such a way that the brush moves through the hair upwards. Repeat the process in the whole facial hair area.
3. After trimming shave the parts around the beard in a usual way.

Trimming a mustache
Trim carefully over a brush to achieve an even cut of the mustache. If you prefer using your finger as a guide, proceed accordingly.

MAINTENANCE

Do not use rough and aggressive detergents! Wipe the trimmer surface with a wet soft cloth.

Cleaning blades
Clean the blades with the brush attached. For thorough cleaning, the entire trimming head A3 can be removed. With your thumb, push the A4 blades and remove the trimming head in the direction of the arrow. When you want to re- attach it, put the plastic projection in the rear part of the trimming head into the opening in the trimmer and re-attach the trimming head (snap it in). To keep the trimmer in perfect condition, you have to lubricate the list with blades using one or two drops of oil for sewing machines. Do not use hair oil, petroleum jelly or oil mixed with petrol or any other solvent because after evaporation the solid parts of the lubricant could slow down the operation of the blades. Insert the trimming head to the trimmer properly, turn on the trimmer and then turn it off and wipe out the excessive oil from the blades.

Storage
Put the trimmer with the accessories back to the original package at a dry and dust-free place, out of reach of children and incapacitated people.

ENVIRONMENTAL PROTECTION

If the dimensions allow, there are marks of materials used for the production of packing, components, and accessories as well as their recycling on all parts. The symbols specified on the product or in the accompanying documentation mean that the used electrical or electronic products must not be disposed of together with municipal waste. For proper disposal, hand them over at the special collection places where they will be received free of charge. Suitable disposal of the product can help to maintain valuable natural resources and to prevent possible negative impacts on the environment and human health, which could be the possible consequences of improper waste disposal. Ask for more details at the local authorities or at a collection site. Fines can be afflicted for improper disposal of this type of waste in agreement with the national regulations. The appliance is equipped with rechargeable Li-ion batteries with long life. Dispose of the batteries suitably and safely through the special collection networks. Never dispose of the batteries by burning them!

Removing the battery
Have the accumulators replaced only after they are completely dead (i.e. let the trimmer run so long until the motor stops). Screw out all bolts and open the appliance. Gradually disconnect the lead–in wires of the batteries and remove the battery.

TECHNICAL DATA

• Voltage (V) specified on the type label
• Trimmer weight (kg) 0.3
• Appliance Protection Class III.
• Dimensions (H x L x W) 46 x 173 x 40 (without attachments)
• Noise level: Acoustic noise level of 65 dB(A) re 1pW.

Charging adapter

Manufacturer’s name or trademark, business registration number, and address| ETA
---|---
Model identifier| HX-S6LV0501000
Input voltage| 100-240 V (AC)
Input frequency| 50/60 Hz
Output voltage| 5,0 V (DC)
Output current| 1,0 A
Output power| 5,0 W
Average efficiency in active mode| 115 V, 60 Hz: 74,73 %; 230 V, 50 Hz: 74,62 %
Low load efficiency (10%)| 115 V, 60 Hz: 72,46 %; 230 V, 50 Hz: 67,43 %
Power consumption without load| 115 V, 60 Hz: 0,056 W; 230 V, 50 Hz: 0,08 W
Appliance protection class| II.

The manufacturer reserves the right to change the technical specifications and accessories for the respective models. The capacity of the product battery decreases over time. Decreasing of battery capacity occurs during normal use of the appliance and is considered usual wear and tear of the appliance. Decreasing battery capacity is not a defect of the appliance.
More extensive maintenance or maintenance requiring intervention in the inner parts of the appliance must be carried out by professional service!
Failure to comply with the instructions of the manufacturer will lead to expiration of the right to repair!
The information regarding warranty and product repairs you can find on the website www.eta.cz/servis-eu.

WARNINGS AND SYMBOLS USED ON THE APPLIANCE, PACKAGING OR IN THE INSTRUCTIONS MANUAL:
HOUSEHOLD USE ONLY. DO NOT IMMERSE IN WATER OR OTHER LIQUIDS. TO AVOID DANGER OF SUFFOCATION, KEEP THIS PLASTIC BAG AWAY FROM BABIES AND CHILDREN. DO NOT USE THIS BAG IN CRIBS, BEDS, CARRIAGES OR PLAYPENS. THIS BAG IS NOT A TOY.

Oil: Warning, Avoid contact with eyes, Do not drink, Keep away from children or mental capabilities.

References

• ElektroEko – Odbiór odpadów elektro
• ETA - tady je doma
• Servis ETA pro Evropu | ETA - tady je doma
• ETA - tu je doma

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>