arteconfort LOLA Ceiling Fan Instruction Manual

arteconfort LOLA Ceiling Fan

THANKS FOR TRUSTING IN ARTECONFORT
Congratulations, you have just purchased an Arteconfort ceiling fan: cutting edge technology combined with the highest energy efficiency.

WARNING
Read this instruction manual carefully before beginning installation and save it for future reference. In case of transfer of the device, you must also give this instruction manual to the corresponding person.
While using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock and personal injury.

CAUTION

• The product must only be installed by an authorized electrician and in compliance with local, regional and state electricity regulations.
• Check if the electrical specifications of this device are compatible with your installation.
• Turn ot the power betore installing or repairing the tan.
• The tan must be properly grounded to avoid the risk of electric shock.
• Use and unauthorized technical modifications could suppose a risk ot injury.
• The tan must be connected to a 250V 50Hz power supply.
• Do not connect fhe fan mofor fo a current dimmer It could give unsafistactory performance (engine humming) and cause engine damage.
• Be caretul while working near the spinning blad
• Never connect the fan fo a power point but fo the ceiling itselt.
• The tan must be installed so that the blades are at least 2,3 meters above the ground.
• The tan must be hung troma structure capable of supporting a weight of at least 50 kg. The tixture must be able to support the weight ot the fan in motion and should not wobble or loosen.
• Make sure that the blades do not come in contact with any object at the installation site.
• Always leave a minimum clearance ot 50cm trom the tip ot the blades to the wall or ceiling.
• Keep in mind that the larger this space, the better the fan’s air tlow will be.
• Do not use in an open space or where it may be exposed to water or moisture.
• Never install the appliance in a room with a high degree of humidity.
• The tan must not be started in a room with o gas appliance running at the same time.
• This device can be used by children aged 8 years and above and of people wifh reduced physical, sensory or mental abilities or lack of experience and knowledge it they are supervised or instructed about the use of the device safely and understand the risks involved. As well as cleaning and maintenance ot the device.
• Children should not play with the device.
• To reverse the direction ot the blades, do it while moving9
• Do not insert any object into the tan blades while they are rotating.
• This can damage them and alter the balance of the tan and the device can fall down.
• After the tan is fully installed make sure all fasteners are securely tastened to prevent any wobbling or talling ot the machine.
  The instructions and safety regulations in this manual cannot prevent all conditions and Situations that may occur. ror obvious reasons, this manual cannot include factors such as caution and care. These factors must be assumed by who installs, maintains, uses and enjoys the product.

BEFORE INSTALLATION

Open the box ovoiding the use of blodes or “cutters” to avoid scratching the fan components.
Unpack the parts handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surface to prevent damage (you can also use the anti-shock foam on the box for this purpose). Never support the motor sideways.
It is advisable to mount the fan on the floor or a surface large enough so that no component falls.
Identify all parts before beginning assembly.

TOOLS NEEDED

*Not included. It is recommended that the screwdriver be magnetized.

MAINTENANCE

• Over time and due to the natural movement of the fan, some connections may come loose. Check the support connections, brackets and attach the blades twice a year, and make sure they are firm.
• Clean the appliance regularly to maintain its appearance as new. To do this, use a soft, lint-free cloth to avoid scratching the finish. Never use water, because it could damage the motor or the wood of the blades.
• It is not necessary to grease the fan, since the motor bearings permanently contain lubricant.

WARRANTY

You can check the warranty for this product on its corresponding page at the end of this manual.

ENVIRONMENT

Do not throw electrical appliances into the household waste, use selective collection facilities. Consult local authorities for more information.
If electrical appliances are deposited in landfills, hazardous components can seep into groundwater and enter the food chain, damaging health and well- being.
Thanks for taking care of the environment.

PROBLEM SOLVING

Before carrying out the checks detailed below, the fan must be without power supply.

1. The fan does not start
   • Replace the remote control batteries if they are exhausted or not suitable.
   • Check that there are no nearby devices that may be causing interference with the remote or reducing signal reception.
   • Resynchronize the remote control.
   • Check that the electrical connections are correct (must be carried out by a licensed electrician)
   • Check fuses and switches, that the installation has voltage and it reaches the fan.
2. The fan doesn’t start but the light does.
   • With the fan off, check with your hand that the blades turn freely.
3. The fan makes excessive noise while rotating
   • Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
   • Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
   • If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.
4. The fan wobbles
   • Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
   • Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual.
5. The fan does not give air or the air flow is insufficient
   • Check that the blades are not mounted backwards.
   • Check that the blades rotate in the correct direction (Summer/ Winter).
   • Avoid nearby objects that may impede air circulation.
   • Verify that the diameter of the blades of your fan is sufficient for the area of the room in which it is installed.
6. The light does not turn on
   • Check the bulb is not blown, otherwise replaces it with a new one.
   • If your fan has LED light included, check the connections are properly fixed according to the instruction manual.

COLOR TEMPERATURE MEMORY

The fan has color temperature memory of the light. This function allows you to maintain the same color temperature when the fan light is turned on again.
To change the color temperature of the light press. the button indicated with the color of each color temperature.
When you turn the light off and turn it on again it will keep the selected temperature.

REMOTE CONTROL

WINTER/SUMMER MODE (FIR)
Reverse the direction of rotation of the blades to change to summer mode or winter mode.
LAMP ON/OFF (LIGHT ON/OFF)
Turns the light and synchronization on or off (see section “Control synchronization”).
FAN ON/OFF (FAN ON/OFF)
Turn the fan on or off.
SPEED REGULATOR
Increases or decreases the turning intensity of the blades.
LIGHT INTENSITY REGULATOR
Increase or decrease the intensity of the light.
LIGHT TEMPERATURE
Change the color temperature of the light.
PROGRAMMING
Sets the hours of fan operation (2 or 4 hours).
BREEZE MODE
Activate the breeze mode that alternates smoothly between soft and fast speeds (from speed l to 3) to create a greater sensation of comfort.
To activate the breeze mode, activate the fan using the “ON/OFF” button on the fan and then press the “Breeze mode” button.
For cancel breeze mode press the “Breeze mode” button again, the fan will return to the rotation speed selected before the breeze mode. You can also press the “ON/OFF” button of the fan to completely stop the rotation of the blades, when you turn it on again it will not remember the breeze mode, activating at the previously selected rotation speed.

*The remote control is synchronized from the factory, you only need to re-synchronize it if the synchronization has been lost, if you purchased a new one or want to control several fans with a single remote.

BATTERIES

The remote control batteries are included.
The required battery model is 2x AAA.
*Remove the batteries from the control/er if it is not going to be used for a long time.

REMOTE CONTROL SYNCHRONIZATION

The remote is factory synchronized, you only need to resynchronize the remote if you have lost synchronization, purchased a new one, want to control several fans with a single remote, or the fan does not respond to the remote control orders while it is running.

A REMOTE CONTROL TO A NEW FAN

1. Cut the current
   Be sure to cut off the current until the fan stop and wait 30″

2. Restore the current
   Past 30″ re-establish the current.

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button c during 3 seconds until you hear the signal. Control range: 8-l0m.

A REMOTE CONTROL TO VARIOUS FANS

1. Cut the current
   Be sure to cut off the current until all fans stop and wait 30″

2. Restore the current
   Past 30″ re-establish the current.

3. Synchronize the remote control
   Within 10 seconds, press the synchronization button “ON/OFF light” on each fan during 3 seconds until you hear the signal. If they are within a radius of less than l0m (control range: 8-l0m), all will synchronize at the same time.

A REMOTE CONTROL TO A FAN

(Example for two fans, applicable to a larger number of fans)

1. **Cut the fan A current***
   Be sure to cut the fan A current (the one we want to remove the synchronization) and wait 30″.

2. **Cut the fan B current***
   Be sure to cut off fan B (the one we want to synchronize) and wait 30″.

3. Restore fan B current
   When you restore the fan B and within 10 seconds, press the synchronization button “ON/OFF light” during 3 seconds until you hear the signal to synchronize remote control B with fan B.

4. **Cut the fan B current***
   Be sure to cut the fan B current and wait 30″.

5. Restore the fan A current
   When you restore the fan A and within 10 seconds, press the synchronization button “ON/OFF light” during 3 seconds until you hear the signal to synchronize remote control A with fan A.

6. Repeat the steps
   Repeat steps with each fan you have and want to individualize its remote control.

*To cut the current you can press the individual fan switch. If there is not, disconnect the quick connect cables from the Fon.

PARTS OF A FAN

SCREW GUIDE

INSTALLATION

WARRANTY

This fan is guaranteed for 3 years. This warranty covers the exchange or repair of any failure or defect of the device, provided that it is due to a manufacturing fault or a defective component.

IMPORTANT
It is essential for the use of this guarantee to prove the purchase date of the product. Therefore, it will be necessary to present the purchase receipt as well as this instruction manual.

Keep the purchase receipt and the instruction manual.

The warranty of this product does not a p p l y if the defects of the device have been caused by:

• D a m a g e during transport not carried out by the manufacturer. (Example: dents, components or glass pieces d a m a g e s … )
• Carrying out incorrect installations or assemblies.
• Poor preservation of the product.
• D a m a g e caused by contact of the device with chemical or inappropriate substances. This fan is designed for indoor use only, so it should not be exposed to water and / or humidity either.
• The replacement or use of additional ports or accessories that are not original from the manufacturer.
• When using a control through a wall dimmer other than the remote control supplied with the fan.
  Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual.

It you have any questions, problems or missing components, consult your dealer You can also contact us through the email info@arteconfort.com or through the contact form available on our website

www.arteconfort.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>