ADLER AD 7727 Ceramic Heater LCD with remote control User Manual
- June 5, 2024
- ADLER
Table of Contents
ADLER AD 7727 Ceramic Heater LCD with remote control
OVERVIEW
SAFETY CONDITIONS IMPORTANT INSTRUCTIONS ON SAFETY OF USE PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
The warranty conditions are different, if the device is used for commercial purpose.”
-
Before using the product please read carefully and always comply with the following instructions. The manufacturer is not responsible for any damages due to any misuse.
-
The product is only to be used indoors. Do not use the product for any purpose that is not compatible with its application.
-
The applicable voltage is 220-240V, ~50/60Hz. For safety reasons it is not appropriate to connect multiple devices to one power outlet.
-
Please be cautious when using around children. Do not let the children to play with the product. Do not let children or people who do not know the device to use it without supervision.
-
WARNING: This device may be used by children over 8 years of age and persons with reduced physical, sensory or mental capabilities, or persons without experience or knowledge of the device, only under the supervision of a person responsible for their safety, or if they were instructed on the safe use of the device and are aware of the dangers associated with its operation. Children should not play with the device. Cleaning and maintenance of the device should not be carried out by children, unless they are over 8 years of age and these activities are carried out under supervision.
-
After you are finished using the product always remember to gently remove the plug from the power outlet holding the outlet with your hand. Never pull the power cable!!!
-
Never put the power cable, the plug or the whole device into the water. Never expose the product to the atmospheric conditions such as direct sun light or rain, etc.. Never use the product in humid conditions.
-
Periodically check the power cable condition. If the power cable is damaged the product should be turned to a professional service location to be replaced in order to avoid hazardous situations.
-
Never use the product with a damaged power cable or if it was dropped or damaged in any other way or if it does not work properly. Do not try to repair the defected product yourself because it can lead to electric shock. Always turn the damaged device to a professional service location in order to repair it. All the repairs can be done only by authorized service professionals. The repair that was done incorrectly can cause hazardous situations for the user.
-
Never put the product on or close to the hot or warm surfaces or the kitchen appliances like the electric oven or gas burner.
-
Never use the product close to combustibles.
-
Do not let cord hang over edge of counter or touch hot surfaces.
-
Never leave the product connected to the power source without supervision. Even when use is interrupted for a short time, turn it off from the network, unplug the power.
-
In order to provide additional protection, it is recommended to install residue current device (RCD) in the power circuit, with residual current rating not more than 30 mA. Contact professional electrician in this matter.
-
Never use this device close to water, e.g.: under shower, in bathtube, or above sink filled with water.
-
If using the device in bathroom after use remove the power plug from the socket, because water proximity presents risk, even if the device is turned off.
-
Do not put your fingers or any objects through the ventilation grille
-
Do not place any objects on the convector. The vents must not be covered by a towel , curtain , etc. may cause a malfunction or fire.
-
Keep the distance between the convector and other items such as furniture , curtains.
-
Convector is equipped with a device to prevent overheating. Automatically turns off the convector in the event of excessive temperature convector (due to clogged vents, fan malfunction ) . In this case, disconnect the unit from the power supply , waiting a few minutes and remove the cause of overheating,
-
Do not touch the hot parts of the convector . Do not touch the appliance with wet hands.
-
In the case of wet convector or falling of any object through the ventilation grille of the convector , turn it off immediately and disconnect from the network. Before re- use
with convector call for service . -
Do not place the convector directly below the electrical outlet.
-
Always turn off the convector button before disconnecting it from the mains.
-
Do not use this heater in the immediate vicinity of a bathtub, shower or swimming pool
-
Do not use this heater if it has been dropped
-
Do not use if there are visible signs of damage to the heater
-
Use the heater on a level and stable surface or attach it to the wall, if provided for by the manufacturer
WARNING: Do not use this heater in small rooms where there are people who
are unable to leave them by themselves, unless constant supervision is
ensured.
WARNING: To reduce the risk of fire, keep textiles, curtains or other
flammable materials at least 1 m away from the heater air outlet.
“Caution Hot Surface” – The temperature of accessible surfaces may be higher when the equipment is in operation, which means that the housing elements become hot during operation during operation, BE CAREFUL !!!
WARNING: In order to avoid overheating – do not cover the heater. The
device is not to be covered with clothing, blankets and other textile products
which could cause ignition.
BEFORE FIRST USE
- This heater is not equipped with a device to control the room temperature. Do not use this heater in small rooms when they are occupied by persons not capable of leaving the room on their own, unless constant supervision is provided. The device cannot be used in room smaller than space of floor 4m2.
DEVICE DESCRIPTION
- LED screen
- Tip-over switch
- LED Screen
- Anti-frost function icon
- Low heating power icon 1E. Timer Icon
- ECO mode Icon
- Control Panel
- ON/Stand-By Button
- Timer Button
- Oscillation Button
- Control panel
- Air inlet at back side
- Fan mode icon
- High heating power icon
- Power Indicator
- Temperature / Time digital icon
- Mode button (fan / low power / high power) 2D. ECO Button
- Temperature / Time Button
- Air outlet
- Power switch
- Base
- Remote control
- Temperature / Time Button
USAGE
- Stand the device on flat, stable surface with 1 meter distance to any objects. Do not stand it on carpets. Switch off the Power switch (7) to position “0” – off. Plug in the device to a 220-240V ~50/60Hz socket.
- To start the device, press the power switch (7) located at the back of device to position “I” – on.
- The power indicator (1F.) will be flashing.
- Press the ON/Stand-by button (2A), your heater will working on Anti-frost function, at the same time, the anti-frost function icon (1A) will light up. The temperature icon (1H) shows present temperature in room. This anti-frost mode keeps the room temperature at 7°C. It means when room temperature is higher than 7°C, it works at fan mode, when the room temperature is lower than 7°C, it works at high power of heating.
- Press the mode button (2B) to select:
- fan mode by pressing once. Then the fan mode icon (1B) will be light up.
- lower heating power 750W by pressing again. Then the low power icon (1C) will be light up.
- high heating power 1500W by pressing again. Then the high power icon (1D) will be light up.
- Press the timer button (2C), the timer icon(1E) will light up, and the twinkle sound appeared. Then press button (2G) to increase time or (2F) to decrease time. You can select the working timer from 0 to 24 hours. The timer digital icon (1H) will shows the number you selected to count down time to switch off the device automatically. After 5 seconds, the timer digital icon (1H) will show the room temperature again.
- Press the ECO button (2D), the ECO mode icon (1G) will light up. Under this function your heater will working in low heating power or high heating power. The ECO function will compare the target temperature with the current room temperature, and it will automatically select the most appropriate heating level to guarantee an optimum comfort level while reducing the energy consumption. While the ECO function is switch on, your heater may switch automatically to low or high heating level even several time.
- Press the oscillation button (2E), your heater will oscillating horizontally from left side to right side, press the button again to stop oscillation.
- Press the temperature decreasing button (2F) or press the temperature increasing button (2G) to set the temperature from 10°C to 35°C . When you set the temperature, the temperature digital icon (1H) will shows the temperature you selected. And after 5 seconds, the digital icon (1H) will show the room temperature again.
- To turn off your heater, press the ON/Stand-By Button(2A). If your heater is working on heating mode, press the ON/Stand-By Button(2A), your heater will working on fan mode for 30 seconds and the digital icon will countdown from 30 to 0 in order to cool down components. Unplug the device when it is not in use.
- Remote control (8) operation is same as manual operation of buttons on control panel (2).
To use the device with the remote control (8) supplied, pull the installing film. In order to remove the battery, simply squeeze the small tab and pull. To replace the battery, insert 1 x CR2025 (3V) lithium battery into the small crevice.
IMPORTANT: The + symbol on the battery inserted should be facing upwards. Firmly close the battery compartment to begin using the remote control (8)
OVER-TIP PROTECTION
The device is protected with a safety switch – named tip-over switch (5) – that turns off the device automatically when the heater falls over, or is at an excessive angle from the horizontal. This helps prevent accidents, and the heater will back to the standby mode. Press the buttons (2A) on control panel to reset the device.
OVERHEATING PROTECTION
- In the event of accidental overheating (for example: obstruction of air intake and outlet grilles, motor turning slowly or not at all), a safety device shuts down the heater automatically. To reset, disconnect the plug from the power for a few minutes, remove the cause of overheating then plug the device in again.
- If you still notice the same defect as above mentioned, remove the plug from the socket and consult your authorized dealer to your after-sales service department.
- During use, do not touch or cover the air outlet. This may cause the unit to overheat, and the safety device to operate.
CLEANING AND MAINTENANCE
- The device must be switch OFF via the power switch (7) and unplugged before proceeding with any cleaning work. Let the device to cool down some minutes before start the cleaning.
- Clean the housing with a lightly damp cloth, a vacuum cleaner or a dusting brush.
- Never use flammable or abrasive cleaning agents such as benzene or spirit to clean the appliance.
- Never immerse the appliance in water!
- Clean the air inlet and outlet regularly with a vacuum cleaner.
- If the appliance is not used for an extended period it must be protected against excessive dust and dirt. Store the heater in a dry place away from sunlight and dirt.
TECHNICAL DATA
- Power 1500W
- Power supply 220-240V ~50/60Hz
To protect your environment: please separate carton boxes and plastic bags and dispose them in corresponding waste bins. Used appliance should be delivered to the dedicated collecting points due to hazarsous components, which may effect the environment. Do not dispose this appliance in the common waste bin.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>