LION APL-PB-2512 Multi Function Panel Light Instruction Manual
- July 25, 2024
- LION
Table of Contents
MULTI-FUNCTION PANEL LIGHT
RADAR SENSOR PANEL LIGHT ULTRA-NARROW EDGE
10mm
APL-PB-2512 Multi Function Panel Light
ULTRA-THIN INDUCTION PANEL LIGHT
● ULTRA-NARROW EDGE DESIGN, MORE BEAUTIFUL
Function Introduction
SENSOR PANEL LIGHT
Radar/Microwave/Motion Sensor
- Adjustable sensor distance and sensor delay time
- 230mm and 300mm size can choose light sensor(only light on in night time)
- Without Sensor Optional
Microwave Sensor Adjust Instruction
1 & 2 Adiust Sensor Distance
| 1 | 2 | Sensor Distance |
|---|---|---|
| OFF | OFF | 8 meters (8 *) |
| OFF | ON | 4 meters (4*) |
| ON | OFF | 2 meters (2*) |
| ON | ON | 4 meters |
Light Sensor OFF
3 & 4 Adjust Sensor Delay Time
| 3 | 4 | Sensor Delay Time |
|---|---|---|
| OFF | OFF | 15 seconds (15 ) |
| OFF | ON | 30 seconds (30 ) |
| ON | OFF | 60 seconds (60 ) |
| ON | ON | Sensor OFF |
3CCT Adjustable By Switch
DIMMING SWITCH
- Intelligent constant current driver, protect from overheat, short circuit, and undervoltage
- PC cover material, anti-uv and high temperature resistance
- 100lm/w-high luminous flux with even light
- Pass CE standard
Three Colors In One reduce your stock pressure, save transportation cost
Power/Brightness Adjustable By Switch
POWER SWITCH
- Intelligent constant current driver, protect from overheat, short circuit, and undervoltage
- PC cover material, anti-uv and high temperature resistance
- 100lm/w-high luminous flux with even light
- Pass CE standard
Three Power In One reduce your stock pressure, save transportation cost
Surface Mounted
Recessed/Concealed Mounted
STEPLESS HOLE CUT
Parameter
ROUND SHAPE MULTI-FUNCTION PANEL LIGHT
COLOR TEMPERATURE
3000K-6000K
90-130LM/W
| Item No. | Power | Adjust Power | Lamp Size | Cut Hole |
|---|---|---|---|---|
| APL-PB-2512-18W | 18W | 9W-12W-18W | D230*H25mm | 55-185mm |
| APL-PB-2512-24W | 24W | 12W-18W-24W | D300*H25mm | 55-255mm |
| APL-PB-2512-30W | 30W | 18W-24W-30W | D400*H25mm | 55-255mm |
FCC Warning Statement
Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance of 20cm the radiator
your body. This device and its antenna(s) must not be co-located or operation
in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>