kogan KAPEPH24WPA Panel Heater User Guide

kogan KAPEPH24WPA Panel Heater

Product Information

Specifications:

• Voltage: 220-240V (1500W), 230-240V (2400W)
• Frequency: 50-60Hz
• Power: 750/1500W (1500), 1200/2400W (2400W)

Product Usage Instructions

Installation:

• Wheels:
  • Carefully turn the heater upside down.
  • Press the x4 wheels into the x2 wheel plates. The wheels will audibly click into place.
  • Secure the wheel plates to the heater using x2 short screws per wheel plate.
  • Place the heater upright.
• Wall Mounting:
  • Insert the x4 wall anchors into the drilled holes.
  • Secure x1 bracket to x2 wall anchors using x2 long screws. Repeat this to secure the other bracket to the other x2 wall anchors.
  • Locate the x2 holes in the back panel of the heater. Secure the x2 spacers to the back panel using x2 short screws.
  • Hook the heater on the brackets.

Operation:

1. Place the heater on a flat, stable surface.
2. Ensure the power knob is turned towards ON.
3. Plug the heater into an electrical outlet.
4. Turn the power knob to the desired fan speed and the temperature knob to the desired temperature. The indicator will illuminate.
5. When the set temperature has been reached, turn the temperature knob anti-clockwise until it audibly clicks. All heating elements and the indicator will switch off.
6. The heater will automatically switch on when the ambient temperature decreases and will automatically switch off when the ambient temperature increases to maintain a comfortable ambient temperature.
7. Unplug the heater if it will not be used for a long time.

Cleaning & Care:
Store in original packaging in a dry, ventilated room. Do not expose the heater to humidity.

Frequently Asked Questions (FAQ):

• Q: Can I leave the heater plugged in all the time?
  A: It is recommended to unplug the heater if it will not be used for a long time to prevent any potential hazards.

• Q: How do I know when the set temperature has been reached?
  A: The indicator light will switch off when the set temperature has been reached, indicating that the heater has stopped heating.

SAFETY & WARNINGS

• The heater is for household use only. This heater should be used only as intended.
• Check the heater carefully before use. Do not switch the heater on with defects or a damaged cord. Contact help.Kogan.com for support.
• Placing the heater in water is forbidden.
• Only plug the heater into an AC power source.
• The heater should be connected to the same voltage as started on the rating label and packaging.
• The heater must only be plugged in to a grounded socket.
• Do not use a non-standard power supply.
• Switch off the heater before plugging it in.
• Do not use the heater outdoors.
• Protect the heater from the impact of the sharp corners and high humidity.
• Do not touch the heater with wet hands.
• If there is water on the surface of the heater, unplug it immediately.
• If the heater falls in water, unplug it immediately. Before next use, the heater should be checked by licensed professional.
• Always unplug the heater after use, before cleaning or if you find defects.
• Do not carry the heater by the cord.
• When you switch off the heater, keep your hand on the plug and pull it. Do not pull the cord.
• Do not wrap the cord around the heater after the use.
• Do not attempt to repair the heater yourself. If the heater or cord are damaged, cease use immediately and contact help.Kogan.com for support.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or metal capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Do not plug the heater in before it is wall mounted or set on wheels.
• Do not cover the heater when it is operating.
• Avoid placing foreign objects in the air vents.
• Do not pull and twist the cord.
• Never leave the heater unattended while in use.

OVERVIEW

COMPONENTS

• Short screws (x6)
• Long screws (x4)
• Wall anchors (x4)
• Brackets (x2)
• Spacers (x2)
• User guide

INSTALLATION

Before Use

• Take the heater out of the box.
• Remove the packaging.
• Check the installation parts.

Wheels

1. Carefully turn the heater upside down.
2. Press the x4 wheels into the x2 wheel plates. The wheels will audibly click into place.
3. Secure the wheel plates to the heater using x2 short screws per wheel plate.
4. Place the heater upright.

Wall Mounting

• NOTES:
  • There must be at least 200mm between the bottom edge of the heater and the floor. Other objects should be at least 200mm from the sides and 500mm in front of the heater.
  • Do not place the heater under an electrical outlet.
  • Do not place the heater in a bathroom or near a swimming pool.
  • This heater has IP24 protection.

1. Drill x2 Ø8mm holes 220mm (1500W) or 500mm (2400W) apart. Then, drill a Ø8mm hole 25mm from the outer side of each hole.
2. Insert the x4 wall anchors into the drilled holes.
3. Secure x1 bracket to x2 wall anchors using x2 long screws. Repeat this to secure the other bracket to the other x2 wall anchors.
4. Locate the x2 holes in the back panel of the heater. Secure the x2 spacers to the back panel using x2 short screws.
5. Hook the heater on the brackets.

OPERATION

1. Place the heater on flat, stable surface.
2. Ensure the power knob is turned towards
3. Plug the heater in to an electrical outlet.
4. Turn the power knob to the desired fan speed and the temperature knob to the desired temperature. The indicator will illuminate.
5. When the set temperature has been reached, turn the temperature knob anti-clockwise until it audibly clicks. All heating elements and the indicator will switch off.
6. The heater will automatically switch on when the ambient temperature decreases and will automatically switch off when the ambient temperature increases to maintain a comfortable ambient temperature.
7. Unplug the heater if it will not be used for a long time.

CLEANING & CARE

• Before cleaning the heater, wait until it cools down and unplug it.
• Do not use abrasives and solvents. Wipe the heater with a soft, damp cloth.
• Remove dust from the surface of the heater regularly.
• Do not wash the heater or place it in water.
• If the heater will not be used for long time, wipe the surface and store it in its original packaging in a dry, ventilated room. Do not expose the heater to humidity.

SPECIFICATIONS

• Voltage: 220-240V (1500W), 230-240V (2400W)
• Frequency: 50-60Hz
• Power: 750/1500W (1500), 1200/2400W (2400W)

Disposal
This marking indicates that this appliance should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up.
For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com.

References

• Kogan Help Centre

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>