ROBe T1 LightMaster Rear User Manual

T1 LightMaster Rear

“`html

Product Information

Specifications:

• Product Name: Robin T1 LightMaster Rear
• Version: 1.1
• Intended Use: Indoor, Professional
• Control Elements: FollowSpot controller
• Interfaces: USB (Type A & B), RJ45

Product Usage Instructions

1. Safety Instructions

For your own safety, please read this user manual carefully
before installing the product.

Caution: The Robin T1 LightMaster is designed
for indoor professional use only, not for household use. Do not use
DMX for control of pan/tilt movement if installed on a tripod.

2. Description of the Robin T1 LightMaster Rear

The Robin T1 LightMaster Rear includes various components such
as front holder, fastening screws, supporting frame, handle,
FollowSpot controller, USB ports, and more. Refer to the user
manual for a detailed description of each part.

2.1 Control Elements of the FollowSpot Controller

The FollowSpot controller features buttons for activation,
blackout, preset settings, pan/tilt control, jog-wheels, faders,
and more. Familiarize yourself with these controls before
operation.

3. Installation

The installation of the Robin T1 LightMaster Rear should be done
by a qualified worker. Ensure to switch the fixture to Follow Spot
Mode (Hard) before installation. It is recommended to have two
workers due to the weight of the supporting frame.

Danger: Avoid putting fingers between the
balance weight and supporting frame during adjustment to prevent
injury. Always secure the position with locks.

4. Operation

Refer to the user manual for detailed operational instructions
on using the Robin T1 LightMaster Rear.

FAQ

Q: Can the Robin T1 LightMaster be used outdoors?

A: No, the product is designed for indoor use only.

Q: How should I control the pan/tilt movement when the fixture

is installed on a tripod?

A: Use the LightMaster for controlling the pan/tilt movement,
not DMX.

“`

QR code for user manual
Version 1.1

Table of contents
1. Safety instructions …………………………………………………………………………………………… 3 2. Description of the Robin T1 LightMaster Rear …………………………………………………. 4
2.1 Control elements of the FollowSpot controller ………………………………………………….. 5 3. Installation……………………………………………………………………………………………………….. 6
3.1 Installation of the Robin T1 on the tripod………………………………………………………….. 9 4. Operation……………………………………………………………………………………………………….. 10
4.1 Functions mapping……………………………………………………………………………………… 10 4.2 Saving and recalling FollowSpot controller presets …………………………………………. 12 5. Control menu …………………………………………………………………………………………………. 14 5.1 Menu Functions Mapping…………………………………………………………………………….. 15 5.2 Menu Show library ……………………………………………………………………………………… 16 5.3 Menu All Lamps On/Off ……………………………………………………………………………….. 19 5.4 Menu Product IDs ………………………………………………………………………………………. 19 5.5 Menu Software Version ……………………………………………………………………………….. 19 5.6 Menu Settings ……………………………………………………………………………………………. 19 6. Software update……………………………………………………………………………………………… 20 7. Technical specifications …………………………………………………………………………………. 21 8. Cleaning and maintenance ……………………………………………………………………………… 22 8.1 Disposing of the product ……………………………………………………………………………… 22
2

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOU INSTALL THE PRODUCT .
1. Safety instructions
CAUTION! The ROBIN T1 LightMaster was designed for indoor use only. The product is for professional use only, it is not for household use.
This product has left our premises in absolutely perfect condition. In order to maintain this condition and to ensure a safe operation, it is absolutely necessary for the user to follow the safety instructions and warnings written in this manual. The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the product. If the device has been exposed to drastic temperature fluctuation (e.g. after transportation), do not switch it on immediately. The arising condensation water might damage your device. Leave the device switched off until it has reached room temperature. Refer servicing to qualified service personnel. Operate the ROBIN T1 LightMaster only after having familiarized with its functions. Do not permit operation by persons not qualified for operating the ROBIN T1 LightMaster. Most damages are the result of unprofessional operation! Please use the original packaging if the ROBIN T1 LightMaster is to be transported. Please consider that unauthorized modifications on the fixture are forbidden due to safety reasons!
Warning! If the Robin T1 is installed on the tripod, the pan/tilt movement of the fixture can be controlled by the LightMaster only. Do not use DMX for control of its pan/tilt move-
ment!
Immunity of the equipment is designed for electromagnetic environments E1, E2, E3 according to the standard EN55103-2 ed.2 Electromagnetic compatibility. Product family standard for audio, video, audiovisual and entertainment lighting control apparatus for professional use. Part 2: Immunity. The product (covers and cables) must not be exposed to a high frequency electromagnetic field higher than 3V/m. The installation company should check levels of possible interferences above the tested levels E1,E2,E3 given by this standard (e.g. transmitters in surrounding area) before installing the equipment. Emission of the equipment complies with the standard EN55032 Electromagnetic compatibility of multimedia equipment ­ Emission Requirements according to class B.
3

2. Description of the Robin T1 LightMaster Rear
1 – Front holder 2 – Front fastening screws 3 – supporting frame 4 – Handle 5 – FollowSpot controller 6 – USB (type A) 7 – Handle 8 – Rear fastening screws 9- Adjusting locks for the balance weight bar 10 – Spring locks of the FollowSpot controller 11- USB (type B) 12 – RJ 45 13 – Balance weight 14 – Base of the FollowSpot controller 15 – Adjusting locks for handle 16 – Locks for front holder The rear fastening screws (8) are screwed to the supporting frame (3) at LightMaster delivery.
4

2.1 Control elements of the FollowSpot controller
1 – Active button (actives the FollowSpot Controller)
2 – BlackOut button 3 – Graphic touch screen 4 – Switch On screen button 5 – Pan button(switches pan and tilt
motors from soft mode to hard mode 6 – Tilt button(switches pan and tilt motors from soft mode to hard mode) 7 – Preset button 8 – Activating button for jog-wheel (23) 9 – Preset button 10 – Activating button for rotary jog- wheel (24) 11 – Preset button 12 – Preset button 13 – Preset button 14 – Preset button 15 – Preset button 16 – Activating button for jog-wheel (25) 17 -Preset button 18 – Activating button for
jog-wheel (26) 19 – Preset button 20 – Preset button 21 – Preset button 22 – Preset button 23 – Jog-wheel 24 – Jog-wheel 25 – Jog-wheel 26 – Jog-wheel 27 – Left fader 28 – Right fader
5

3. Installation
The Robin T1 LightMaster Rear has to be installed by a qualified worker on the Robin T1. Important!
Switch the fixture to the Follow Spot Mode (option Hard ) before installing the Robin T1 LightMaster Rear.
The installation should do two workers as the supporting frame of the T1 LightMaster is heavy.
Danger! Never put fingers between the balance weight (13) and the supporting frame (3) when you adjust the position of the balance weight. There is a danger of injury of
your fingers by the heavy balance weight. Always secure adjusted position of the balance weight by means of two locks (9).
1. Switch the Robin T1 to the Hard option of the Follow Spot Mode (Personality–>Follow Spot Mode –>Hard). 2. Disconnect the fixture from mains and place it on a flat surface (e.g. table). Move the head to a horizontal position and lock the tilt movement. 3. Remove the rear cover (A) of the T1 head by unscrewing two screws (B) on both sides of the head and four screws (C) on the rear side of the head. 4. Screw the new rear cover (it is part of Robin T1 LightMaster rear delivery) on the head. Check the screws are fully tightened.
6

5. Unscrew the four locks (16) and remove the front holder (1) from the supporting frame (3).
6. Screw the front holder (1) on the head by means of six screws (2). 7. Insert the supporting frame (3) under the head and screw it on the head by means of the four rear screws (8) and by means of the four locks (16) to the front holder (1).
7

Note: The four rear screws (8) are screwed in the supporting frame (3). Unscrew them before inserting the supporting frame (3) under the head
8. Attach the FollowSpot Controller (5) to the FollowSpot Controller base (14). During attaching, both spring locks (10) have to be in an unlocked position (pressed towards the Follow Spot Controller).
9. Connect the FollowSpot Controller base (14) with the fixture base (18) by means of the USB cable (17).
10. Use the balance weight (13) to balance the head in a horizontal position. Always secure the balance weight in adjusted position by means of the balance locks (9).
8

3.1 Installation of the Robin T1 on the tripod
1. Unfold and adjust height of the tripod and distance of legs (8) by means of adjusting locks (4,5,6,7). The lock (3) has to be in a lower position (as shows arrow on picture below).
2. After inserting the adaptor (1) with spigot (2) to the tripod, the spigot (2) has to be secured by means of the lock (10) and the adaptor (1) by means of the pin (11) which is inserted to the hole (13) of the adaptor (1) as shows arrow on picture below. Position of the pin(11) has to be secured by means of the lock (12).
3. The four quarter -turn locks (9) of the adaptor serve for fastening the Robin T1 with installed LightMaster on the tripod with adaptor. Two workers should install the Robin T1 fixture on the assebled tripod with the adaptor. Check all quarter-turn locks (9) are fully tightened before operating the fixture.
Check that all locks (3, 4, 5,6,7, 10,12) are fully tightened before placing the Robin T1 with installed LightMaster on the tripod with adaptor.
Warning! If the Robin T1 is installed on the tripod, the pan/tilt movement of the fixture can be
controlled by the LightMaster only. Do not use DMX for pan/tilt movement!
9

4. Operation
After installing the ROBIN T1 LightMaster on the fixture and connecting with the fixture via USB cable, connect the fixture to mains and leave it to perform resets (except pan/tilt reset). After finishing resets, the fixture is in the FollowSpot mode with pan/tilt motors in the Soft mode. Press the button ACTIVE (1) in order to activate the FollowSpot Controller. By pressing either the PAN button (5) or the TILT button (6) you will switch both pan and tilt motors of the fixture to the Hard mode of the FollowSpot mode. The button BLACK OUT (2) closes light output of the fixture.
4.1 Functions mapping
After switching the fixture on, the touch screen of the FollowSpot Controller shows the initial screen:
Note: the massage “Waiting for controller” means the FollowSpot Controller is not connected with the fixture via USB cable. Touch the icon to display the password entering screen:
Enter the password (default password is 5242) to enter the main menu of the FollowSpot Controller. The password prevents unauthorized person from changing setting of the FollowSpot Controller. Enter the menu “Functions Mapping”. The list of available effects will appear:
10

If the message” Please Activate FollowSpot Controller!” will appear, press the ACTIVE button (1) on the Follow Spot Controller.
To assign an effect to the Jog-wheels and faders 1.Touch desired effect. Buttons (8/10/16/18) which activate jog-wheels (23/24/25/26) and buttons (20/22), which matches faders (27/28) will start to flash.

2.Press desired button and selected effect will be assigned to its jog-wheel (fader).

Assigned effect is displayed in a yellow colour, free effects stay in a white colour.

3.Repeat steps 1 and 2 for needed effects. 4.Touch the [cancel] icon and than [back arrow]

icon.

The

screen

wOaiptnhplyeeaeffrfefoecnct tfstahdaisesrsssicgrwneieelldna.tpoptehaer.jog- wheels

will

E.g.

Effects assigned to faders (27/28) will not

be shown.

Sensitivity of the jog-wheels assigned to the effects can be set at three levels: low, medium and high. The levels of the sensitivity are marked in colour on the screen:
low level – green slider medium level -yellow slider high level- red slider
In order to switch a jog-wheel to desired level of sensitivity, press and hold its activating button (8/10/16/18) until the colour of fader is changed.
11

Effects assigned to the four jog-wheels and two faders have a priority over DMX values coming from a DMX controller. Functionality of the Robin T1 LightMaster can by restricted by means of commands on the channel Power/ Special Functions of the Robin T1 as follows: 225-229 DMX -LightMaster enabled 230-234 DMX – LightMaster disabled (except two faders on its handle bar and pan/tilt) 235-239 DMX – LightMaster disabled (except pan/tilt)
To control desired effect 1.Use its fader on the screen or press the activating button for its jog-wheel and use this jog wheel or use a corresponding fader. The FollowSpot Controller overwrites fixture channels which are mapped to its jog-wheels or faders, excepting a dimmer. The dimmer value is a combination of value coming from DMX console and a value on the FollowSpot Controller (e.g. DMX console sends 180 DMX, jog-wheels shows 50%, real DMX value coming to fixture is 90 DMX). In case that the DMX console does not send DMX data, the FollowSpot Controller allows full range (0-255 DMX) of dimmer control.
To release an effect from the jog-wheel (fader) 1.Touch desired effect from the list of effects in the menu “Functions Mapping”. 2.Touch the option “Unlink”. 3.The effect will be displayed in a white colour. The item “All” allows to release all assigned effects at one go.
4.2 Saving and recalling FollowSpot controller presets
The FollowSpot Controller offers to save up to 12 presets.
To save a preset 1. Press and hold one of the preset buttons (7/9/11/12/13/14/15/17/19/20/21/22) e.g. button (7) until the jogwheels activating buttons (8/9/16/18) and the pan/tilt buttons (5/6) start to flash.

2. Press flashing continually).

button

of

effect

which

value

you

wish

to

add

to

the

current

preNsoette(:thvealbuuetstoonnwfilal dsetarsrt cannot be included to

light

presets.

12

3. Press and hold selected preset button until jog-wheels activating buttons stop to flash. Note: the FollowSpot controller presets are common for all user show and cannot be saved on the USB flash drive. If you use the FollowSpot Controller in the RoboSpot, the FollowSpot controller presets will be overwriten by presets from RoboSpot. To recall the FollowSpot controller preset Press a button with stored FollowSpot Controller preset. To delete the FollowSpot controller preset 1. Press and hold desired preset button until the jog-wheel activating buttons (8/10/16/18) and the pan/tilt buttons (5/6) start to flash. 2. Press and hold selected preset button until the jog-wheels activating buttons stop to flash. Do not press any jog-wheels activating button. The preset button will stop to light. Note: you can write notes on the white fields of the FollowSpot Controller, use a marker on an alcohol base and
13

a suitable cleaning liquid (on alcohol base) for removing the notes. Never use solvents!
5. Control menu
The FollowSpot Controller is equipped with the QVGA Robe touch screen with battery backup which allows to set the device behaviour according to your needs.
Icons used in the touch screen menu: – [back arrow] used to move back to the previous screen (or menu level). – [up arrow] used to move up on the previous page. – [down arrow] used to move down on the next page. – [confirm] used to save adjusted values and leave menu or to perform desired action. – [cancel] used to leave menu without saving changes. – [display on/off] used to switch on/off the display. – [menu enter] used to enter fixture menu.
Note: buttons are not functional yet. Touch the icon to display the password entering screen:

Enter the password (5242) to enter the main menu of the FollowSpot Controller. The password prevents unauthorized person from changing setting of the FollowSpot Controller.

Main menu Page 1

Page 2

14

5.1 Menu Functions Mapping
By entering the menu you can assign effects from the list of available effects to the jog-wheels and faders. The item All – releases all assigned effects at one go.

List of available effect channels: Fixture

Effect

Available DMX values

15

Robin T1 Profile

Dimmer Iris Focus Zoom Frost V Color Red Green Blue Amber L Green CTO Efw. pos Efw. rot RGW RGW r Prism Pris r FS rot FS 1 m FS 1 s FS 2 m FS 2 s FS 3 m FS 3 s FS 4 m FS 4 s

0-255 0-179 0-255 0-255 0-50, 87-136, 173-222 0-132 0-255 0-255 0-255 0-255 0-255 0-255 0-127 0-255 0, 32-59 0-255 0-127 0-255 Down bu0tt-o2n55 0-255 Confirm button 0-255 Edit butt0o-n255 Cancel b0u-2tt5o5n 0-255 0-255 0-255 0-255

5.2 Menu Show library
The menu item offers 10 user shows. In the show is saved: Functions mapping of the FollowSpot Controller Sensitivity of jog-wheels Faders switching and inversion
The show can be saved on a USB flash drive and load to the FollowSpot Controller if need.

To select a show 1. Enter the menu “Select/rename Show”
16

2. Select desired show and confirm it. To rename a show 1. Select a show and touch the Edit button.
2. Edit the name of selected show by means of the alphanumerical keyboard. Function keys has the following meaning:
ALT key- switches among keyboards:
DEL key – deletes a character Sh key – shift key, changes order of displayed characters aA —> Aa. The key 0_ serves as a space bar. To export a show 1. Disconnect the FollowSpot Controller from the FollowSpot Controller base and connect a USB flash drive to the USB port on the bottom side of the FollowSpot Controller.
2. Press and hold the On button until the graphic touch screen will light (the screen lights about 20 sec and after that will be switched off unless you touch any icon).
17

3. Select option “Export Show”
4. Select show and confirm it.
Wait until the message “Show Saved” appears on the screen. Touch the Cancel button. Default name of saved show file on the USB flash drive has the following sentence structure e.g. lightmaster-1-0031.cfg
lightmaster-2-0031.cfg where the number 1 (2,3,…10) represents a number of show, the number 0031 represents last four numbers of RDM UID of the FollowSpot Controller. Note: if you save some show more than once, original file is not overwritten, files are differentiated by a number after underscore character e.g:
lightmaster-2-0031.cfg lightmaster-2-0031_1.cfg lightmaster-2-0031_2.cfg To import a show 1. Disconnect the FollowSpot Controller from the FollowSpot Controller base and connect a USB flash drive to
18

the FollowSpot Controller and switch the graphic touch screen on as described above in article To export a show. 2.Select option “Import Show”
3. Select show to which you want to load a show file from the USB flash drive and confirm it.
4. Select desired show file to load it.
After loading, the message ” Show Loaded” will appear on the screen: Touch the Cancel button.
5.3 Menu All Lamps On/Off
The menu item allows to switch on/off lamp in the Robin BMFL FollowSpot.
5.4 Menu Product IDs
Select this menu item to read a MAC Address , RDM UID, and RDM Label.
5.5 Menu Software Version
Select this item to read the software version of the fixture modules: Display System – a display processor Module C – a control panel processor
5.6 Menu Settings
System Test – the menu allows you to test jog-wheels and faders. Ethernet Settings – The menu allows to set the FollowSpot Controller for Ethernet operation.
Ethernet Mode Artnet – Fixture receives Artnet protocol gMAI – Fixture receives MANet I protocol gMA2 – Fixture receives MANet 2 protocol 19

sACN – Fixture receives sACN protocol IP Address/Net Mask – Select this menu to set IP address. IP address is the Internet protocol address.The IP uniquely identifies any node (fixture) on a network. There cannot be 2 fixtures with the same IP address on the network!
Default IP Address -Preset IP address, you can set up only first byte of IP address (2 or 10) e.g. 002.019.052.086. Custom IP Address – The option enables to set up all bytes of IP address. Net Mask – The option enables to set up all bytes of Net Mask. ArtNet Universe – Use this item to set a Universe (0-255). The Universe is a single DMX
512 frame of 512 channels. MANet Settings – Use this menu to set parameters for MANet operation.
MANet Universe I/II – The value of this item can be set in range 1-256. MANet Session ID – The value of this item can be set in range 1-32. sACN Settings – Use this menu to set parameters for sACN operation. sACN Universe – The value of this item can be set in range 1-32000. sACN Priority – The value of this item can be set in range 0-255. Controls invert – the menu item allows you to invert faders of the Light Master.
20

Default settings of faders: fader down-minimum (0 DMX), fader up-maximum (255 DMX).
Faders Switch – swaps functions of faders.
Password Settings – the menu item allows you to change the password or switch it on/off at entry the FollowSpot Controller menu.
Change password – use this option to change password. Default (factory) password is 5242. Protect with Password – If this function is on, the password is required at entry the FollowSpot Controller menu. Note: both menu items stated above require inserting of password to enter them even the password is set off ! You have to remember last set password! In case you have forgotten your password, use the master password 4678.
Recalibrate Touchscreen – The item starts calibration of the touchscreen. Follow instructions on the screen. Default Settings – The menu item allows you to set the items stated above (except Ethernet Settings) to default values. Note: the password will not be set to a default password (set password will remain without change) but the option “Protect with Password will be set to On”.

6. Software update
The FollowSpot Controller software update is done via a network connection between a computer running a ROBE RDM Uploader software through the RJ45 input of the FollowSpot Controller base. It is important to note, that the FollowSpot Controller IPv4 address has to be set to 2.x.x.x network (for example 2.0.1.10) with netmask 255.0.0.0 . During the update, the FollowSpot Controller has to be attached to FollowSpot Controller base and this base has to be connected to the Robin T1 by means of the USB cable. The Robin T1 fixture has to be connected to mains.
To update software in the FollowSpot Controller. 1. Connect a computer running ROBE RDM Uploader to the internet and update software libraries (Libraries Update) 2. Connect the computer and the FollowSpot Controller base via Ethernet cable. 3. Set computer to address 2.x.x.x/255.0.0.0. Do not change any IP settings on the FollowSpot Controller. 4. Use the ROBE Uploader Devices Discovery and Devices Update. This will update the FollowSpot Controller.
7. Technical specifications

Input voltage: Setting & Control: Number of control elements: Connection: Fastening: Weight:
Dimensions (mm)

5V DC graphic touch screen 20 buttons, 4 jog-wheels and 2 faders 1 x USB A,1x USB B, 1x RJ45 via 7 screws 7.7 kg

21

Included items 1 x Robin T1 LightMaster Rear 1 x Adaptor LM/Esprite/T1 (P/N 17042037) 1 x BMFL Base adaptor for FollowSpot (P/N 10980365) 1 x Tripod for RoboSpot, FollowSpot, LightMaster (P/N 10980350) 1 x USB cable A-B, 1.8m length (P/N13050756) 1 x User manual
8. Cleaning and maintenance
A soft lint-free cloth moistened with suitable cleaning fluid is recommended, under no circumstances should solvents be used! More complicated maintenance and service operations are only to be carried out by authorized distributors.
8.1 Disposing of the product
To preserve the environment please dispose or recycle this product at the end of its life according to the local regulations and codes.
Copyright © 2022 -2024 Robe Lighting – All rights reserved Specifications are subject to change without notice. April 25, 2024 Made in CZECH REPUBLIC by ROBE LIGHTING s.r.o. Palackeho 416/20 CZ 75701 Valasske Mezirici
22

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>