StarTech CPUMOBILESTND Computer Tower Cart Instructions
- July 25, 2024
- StarTech
Table of Contents
- StarTech CPUMOBILESTND Computer Tower Cart Instructions
- Product ID
- CPUMOBILESTND
- Package Contents
- Requirements
- Installation
- Assemble the Mobile CPU Stand
- Operation
- Adjust the Width
- Regulatory Compliance
- Warranty Information
- Limitation of Liability
- Read More About This Manual & Download PDF:
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
StarTech CPUMOBILESTND Computer Tower Cart Instructions
Product ID
CPUMOBILESTND
Component | Function | |
---|---|---|
1 | Left Side Wall | • Keeps the Computer Case in place |
2 | Adhesive Foam Pads | • Helps prevent the Computer Case from |
slipping
3| Width Adjustment Slots| • Allow to adjust the width to
accommodate different
Computer Case sizes
4| Right Side Wall| • Keeps the Computer Case in place
5| Front Casters| • Allow for flexible placement of the Mobile CPU
Stand
• Brakes prevent unintended movement
6| Rear Casters| • Allow for flexible placement of the Mobile CPU Stand
Package Contents
- Casters x 4
- Side Walls x 2
- Base x 1
- Adhesive Foam Pads x 3
- Assembly Screws x 4
- Wing Nuts x 4
- Washers x 4
- Wrench x 1
- Quick-Start Guide x 1
Requirements
For the latest requirements, please visit www.startech.com/CPUMOBILESTND
- Computer case width of 2 to 8.6 in (132 to 220mm)
Installation
Assemble the Mobile CPU Stand
-
Carefully remove the adhesive backing of the Anti-Slip Pads (x 3). Attach the
Anti-Slip Pads to the Left and Right Side Walls , and the top of the Base. (Figure 1)
Note: All Adhesive Foam Pads are the same size. -
Insert the Assembly Screws (x 4) through the Left and Right Side Walls , and the Base.
Insert the Assembly Screws (x 4) into the Washers (x 4), and the Wing Nuts (x 4) rotate the Wingnut (x 4) to Tighten. (Figure 2). -
Insert the Casters into the threaded holes located in each of the Corners of the Base. Rotate the Casters (x 4) to tight Use the Brake Tabs on the Casters to prevent them from rolling. (Figure 3)
Note: Ensure the Casters with Brake Tabs are installed next to each other at the front or _rear of the CPU Mobile Stand.
_
- Use the Wrench to securely Tighten the Casters (x 4) to the Base.
Operation
Adjust the Width
- Loosen the Wingnuts (x 4) just enough to slide the Left and Right Side Walls on the Width Adjustment Slots towards the Inside or Outside depending on the width of the Computer Case.
- Rotate the Wingnuts (x 4) to tight them and set the desired
Regulatory Compliance
Use of Trademarks, Registered Trademarks, and other Protected Names and
Symbols
This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the third-party company in question. StarTech.com hereby acknowledges that all trademarks, registered trademarks, service marks, and other protected names and/or symbols contained in this manual and related documents are the property of their respective holders.
Warranty Information
This product is backed by a 5-year warranty.
For further information on product warranty terms and conditions, please refer
to www.startech.com/warranty.
Limitation of Liability
In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their officers, directors, employees or agents) for any damages (whether direct or indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, loss of business, or any pecuniary loss, arising out of or related to the use of the product exceed the actual price paid for the product. Some states do not allow the exclusion or limitation of incidental or consequential damages. If such laws apply, the limitations or exclusions contained in this statement may not apply to you.