prodatakey RPW Red Pedestal Wireless Controller User Guide
- June 10, 2024
- prodatakey
Table of Contents
prodatakey RPW Red Pedestal Wireless Controller User Guide
Package Contents
-
Battery Leads (1)
-
Diodes (2)
-
Red Pedestal Controller (1)
-
Wireless Module (1)
-
Rail Bender (1)
-
Jumpers (4)
-
Transformer (1) 14 VDC, 2 Amp
-
Antenna (1)
-
Bolts (4)
-
Nuts (4)
Mounting Controller
Reader Connection
A Reader – The reader is mounted at the door with a 22/5 or 22/6 wire
running to the door controller. Wire the reader to the controller as shown
above. Be sure to check polarity and voltage prior to powering the controller.
B OSDP – Place jumper to enable OSDP (see reference guide for more
information about OSDP)
C Piezo – Can be connected to available relay and configured with
software
Input A / DPS Connection
A DPS (Door Position Switch) – The DPS is mounted on the door frame with
a 22/2 wire running from the DPS to the controller. Wire the DPS to the
controller as shown above. For reporting double doors, wire the two door
position in series and connect to the controller.
B AUX Input – A software rule can be programmed to trigger events or
outputs based on input triggers.
Input B / REX Connection
A Maglock – When installing a Maglock, it is typical to install a REX
(request to exit) at the door for free egress. Run an 18/2 wire from the
maglock to the controller and REX as shown.
B REX (Request to Exit) – The REX is mounted at your desired location
with an 18/5 wire. Wire the REX to the controller and maglock as shown above.
If reporting is not needed in the system, simply eliminate the green input
wire.
C Jumper Block – Use to designated (+) or (-) board voltage out of NO and
NC. If the jumper is off, the relay is a standard dry contact requiring an
input into C on the relay.
D AUX Input – A software rule can be programmed to trigger events or
outputs based on input triggers
Locking Relay
A Gate Operator – Follow the gate operator wiring instructions to connect
the gate operator to an ELK 912B Isolation Relay.
B Isolation Relay – Installation of an ELK 912B isolation relay is
recommended to prevent electrical damage to the Red Gate, The isolation relay
is sold separately.
C Locking Relay – Connect the ELK 912B isolation relay to the controller
by connecting the positive wire into a positive port and the negative wire
into the NO port on the board.
D Jumper Block – Use to designated (+) or (-) board volatage out of NO
and NC. If the jumper is off, the relay is a standard dry contact requiring an
input into C on the relay negative (-) and center pins.
Communication Connections
A Wireless – This controller comes with a prefixed WiMAC Antenna and wireless module.
Power Connection
A DC INPUT – Input 12-24 VDC power using an 18/2 wire. For high voltage
applications, use the High Voltage Converter (PN: HVC).
B BATTERY – The enclosure will fit most 12 VDC 1.2 Ah batteries. Connect
the battery to the controller using the supplied battery leads.
OSDP Reference Guide
What is OSDP – Open Supervised Device Protocol (OSDP) is an access control communications standard developed by the Security Industry Association to improve interoperability among access control and security products. OSDP brings heightened security and improved functionality. It is more secure than Wiegand and supports AES-128 encryption.
OSDP Wire Specication – Four-conductor twisted-pair with overall shield is recommended to remain fully TIA-485 compliant at the maximum supported baud rates and cable distances.
NOTE – It’s possible to reuse existing Wiegand wiring for OSDP, however, using simple stranded cable typical of Wiegand readers generally does not meet the RS485 twisted pair recommendations.
OSDP Multi-Drop – Multi-drop gives you the capability to accommodate many readers by running one length of four-conductor cable, eliminating the need to run wire for each wire.
NOTE – The maximum number of readers each port can support is four.
NOTE – Wiegand readers will not work when OSDP jumpers are installed.
Reference Guide
Fire Input – To integrate the fire system into a controller, refer to wiring diagrams at www.prodatakey.zendesk.com
Programming – After the controller is connected, access the configuration software as instructed in the programming manual availabe at www.prodatakey.zendesk.com
Reader Compatibility – PDK does not require proprietary readers. Controllers accept a Wiegand input, including biometric readers and keypads. OSDP readers are supported by using included jumper (see OSDP reference guide). Contact pdk support if assistance is needed.
UL 294 Compliance – All equipment must meet appropriate UL certifications. For UL listed installations, all cable runs must be less than 30 meters (98.5’)
Part Number – RPW
PDK Technical Support
Phone: 801.317.8802 option #2
Email: [email protected]
PDK Knowledge Base:
www.prodatakey.zendesk.com