MONSTER MQH08 Maxstar Bluetooth Handset Instruction Manual

: July 22, 2024
: Monster

Table of Contents

Monster Maxstar MQH08
- Bluetooth headset
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Monster Maxstar MQH08

Bluetooth headset

Instruction manual

Product parameters

Bluetooth version—————— V5.4
Transmission distance ———— 10m
Driver diameter ——————– 40mm
Driver impedance —————– 16Ω±15%
Sensitivity ————————— 97dB±3dB
Frequency response ————— 20Hz-20KHz
Battery capacity——————— 600mAh 3.7V
Music playtime ———————- ≈60 hours
Charging time ———————— ≈2 hours
Rated input ————————— 5V⎓1A

Product Schematic Description

Headphone*1

Charging case*1

Instructions for use and Warranty card*1

Battery usage note

If the battery is not replaced properly, there is a risk of explosion.
Batteries can only be replaced with batteries of the same type or equivalent.
It is not recommended to replace the battery without permission.
You can return the battery to the manufacturer for replacement.
The battery (battery pack or battery combination) shall not be exposed to lighting, Baking or similar overheating environment.

Product Schematic Description

1 Volume plus button
2 Volume reduction button
3 Multi-function Button (MFB)
4 Charging Type-C jack
5 The switch machine key

Product operating instructions

1. Power on/off
Earphone off state: the on/off button will display the real Power for 4 seconds, and hear the “Power on” voice prompt, and the earphone is turned on.
Headset on state: the switch button displays the real Power for 4 seconds, and hears the “Power off” voice prompt, and the headset is turned off.

2. Pairing up
Press and hold the on/off button to turn on Bluetooth and search for smart devices “Monster Maxstar MQH08” headphones for pairing,
Tap Connect, and you’ll hear “Connected” when the match is complete.
Note: When first used and turned on, the headset will automatically enter pairing mode. This product has Bluetooth memory function, use again
Just turn on the headset and device and connect back automatically.

3. Volume control
Turn up the volume: Press + for the volume.
An prompt tone is played at the maximum volume.
Turn down the volume: short press the volume “-“,
An announcement tone is played at the minimum volume.

4. On the phone
Answer/end a call: Short press MFB
Reject an incoming call: Long press MFB for about 2 seconds
Last Call Redial: Double tap MFB to redial the last call number.

5. Music
Play/pause: Short press MFB;
Previous song: Long press the volume “+” button for 2 seconds;
Next song: Long press the volume “-” button for 2 seconds.

6. Voice control function
Wake up Siri: Three hits MFB.

LED guide light

Mode	Operation method	Sound prompt
Power On	Press the button of the switch machine for 3 seconds, Earphone on
“power_on”	The ice blue light is on for a long time and goes out for 1S
Power Off	Hold down the switch button for 5 seconds, Earphone off
“power_off”	The red light is on for a long time and goes out for 1S
Pairing	The headset automatically enters the pairing state after being turned
on	“pairing”	Ice blue and red lights flicker alternately
Connected	Aer the phone searches for the Bluetooth pairing name, click the
pairing name to connect, and the connection is successful	“connected”	Ice

Reset the device

Boot unconnected state: Press and hold the “+” and “_” keys for 10S at the same time and turn off (clear all pairing and connection information)

Take responsibility for your listening ability

To avoid hearing damage, make sure to turn down the volume of the music player before connecting the headphones. A er putting on the headphones, slowly adjust the volume to the right level. The noise level is measured in decibels (dB). Exposure to noise levels of 85dB or higher may cause progressive hearing loss. Monitor usage; Hearing loss is the result of both too much noise and time. The louder the sound, the less time you have to spend in it. The so er the sound, the longer you can listen. This noise level (dB) table compares and ranks commonly-heard sounds with their potential to cause hearing loss. Make the best use of your equipment and enjoy the best sound from a safe range. Our headphones allow you to capture more sound detail at an unprecedented low volume. Learn how to establish a secure listening level and review other important safety guidelines on the Consumer Electronics Association website (www.ce.org). Important information on how to prevent noise-induced Hearing loss (NIHL) and a complete list of the types of noise that can cause hearing loss can be found on the Hearing Impairment Research Foundation website at WWW.drf.org.

FCC statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC ID: 2A8PV-QSMMQH08

Precautions

Regular cleaning, long life, if not used for a long time, it is recommended to charge once every 15 days to extend battery life, the charging part of the headset tail plug is oen wiped with cotton swab alcohol, which can help smooth charging, avoid bad contact, affecting the use experience.
The battery [battery pack or battery combination] shall not be exposed to lighting, baking or similar overheating environment.
Because this product adopts wireless connection mode, it is affected by environment, mobile phone brand, usage behavior and other factors in daily use. It may be normal to have a brief, slight sound delay during the playing of music.

Warnings

Do not use headphones at high volume for an extended perios of time.
Keep the headphones away from dust and water.
Do not disassemble the headphones and accessories, otherwise warranty will be voided.
Keep headphones away from any impact or vibration.
Do not use any chemical solvents or cleaning agent on the headphones.

Name of the Parts	Hazardous Substances
Pb	Hg
Housing	O
Loudspeakers	O
PCBA	X
Accessories	X

This table is compliled according to SJ/T 11364

O : Indicates that this hazardous substance contained in all of the homogeneous materials for this part is below the limit requirement in GB/T 26572.
X : Indicates that this hazardous subatance contained in at least one of the homogeneous materials used for this part is above the limit requirement in GB/T 26572.

Environment Friendly Use Period (EFUP)

This logo refers to the period (10 years) during which the hazardous substances in electronic and electrical produsts will not leakor mutate so that the use of these [substances] will not result in any severe environmental pollution, any bodily injury or damage to any assets.

Warranty Service

Dear user, this warranty card is the proof of your future warranty application, please cooperate with the seller to fill it out and keep it for future use!
User info

User info

User name| | Email|
Contact number| | Postal code|
Mailing address|
Product information

Product name | | Product number |
Product barcode / Serial number / Batch number |
Vendor information

Certificate of Approval
Product No:
Production Time: PASS
QC:

FCC Warning:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiateradio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or m ore of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device com plies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device m ay not cause harmful interference, and (2) this device m ust accept any interference received, including interference that m ay cause undesired operation. This equipment com plies with FCC radiation exposure lim its set forth for an uncontrolled environment. This equipment should be installed and operated with minim um distance 0cm between the radiator and your body.