Vaporesso GEN MAX/SE Vape User Manual
- July 21, 2024
- VAPORESSO
Table of Contents
Vaporesso GEN MAX/SE Vape
Specifications
- GEN MAX:
- Dimensions: 141.4 x 49.7 x 28.5mm
- Tank Capacity: 6ml/2ml
- Coil Resistance: GTi 0.2 Mesh Coil, GTi 0.4 Mesh Coil
- Battery Capacity: 2 x 18650 Battery
- Output Power: 5-220W
- Charging Current: DC 5V/2A, Type-C
- Display: 0.96 TFT Screen & LED Light
- GEN SE:
- Dimensions: 141.4 x 35.6 x 26mm
- Tank Capacity: 3ml/2ml
- Coil Resistance: GTi 0.2 Mesh Coil, GTi 0.4 Mesh Coil
- Battery Capacity: 1 x 18650 Battery
- Output Power: 5-80W
- Charging Current: DC 5V/2A, Type-C
- Display: 0.96 TFT Screen
Product Usage Instructions
Install the Tank
Install the tank to the battery by screwing the base of the tank. Ensure a firm connection.
Replace the Coil
- Unscrew the base from the tank.
- Pull out the used coil from the tank.
- Install a new coil to the tank.
- Reattach the thread base into place.
Fill E-liquid
- Push the refilling top cap.
- Fill e-liquid through the hole, then lock the top cap in place firmly after the filling is finished.
- Please wait 5 minutes for the e-liquid to soak into the coil completely.
Thank you for choosing the Vaporesso product. Please read this instruction carefully before use to ensure a perfect experience. If there is any additional requirement about this product, please consult the local agent or contact us through our website: www.vaporesso.com
EXPLODED VIEW
GEN MAX
GEN SE
FIGURE
USER INSTRUCTIONS
Install the Tank
Install the tank to the battery by screwing the base of tank. Make sure they
are firmly connected.
Replace the Coil
- Unscrew the base from the tank;
- Pull out the used coil from the tank;
- Install a new coil to the tank;
- Reattach the thread base into place.
Refer to the figure 1.
Fill E-liquid
- Push the refilling top cap.
- Fill e-liquid through the hole, then lock the top cap in place firmly after filling is finished.
- Please wait 5 minutes for the e-liquid to soak into the coil completely.
Refer to the figure 2.
Adjust the Airflow
To adjust the airflow volume, please rotate the air-inlet ring on the top of
the tank.
Power On/Off the Device
Power on/off: press the power button 5 times in 2s.
Power Adjustment
GEN MAX/SE is using the powerful GTi coil platform, and the suggested power
need to be noticed before start vaping.
Start Vaping
Press the power button to enjoy an extraordinary vaping experience.
Charge the Battery
After connecting the Type-C cable to the battery, the battery indicator and
remaining charging time will be showed on the screen.
Lock or unlock the device
Slide the lock button to lock the MOD, and slide back to unlock.
Choose a Mode
Press the power button 3 times continuously to enter the menu setting.
-
F(t): F(t) MODE (DEFAULT)
F(t) MODE is by adjusting temperature, heating speed and time, F(t) mode releases the flavors of e-liquid adequately, delivering the perfect balanced tasting experience consistently from the first puff throughout. -
PUL: PULSE MODE
PULSE MODE is a mode to improve vaping experience through constant voltage output, delivering optimal flavor production, throat hit, nicotine satisfaction, and perfect temperature cloud continuously. -
ECO: ECO MODE
ECO MODE is a normal mode of output wattage, you can according to the coil resistance to adjust the best wattage for your needs. The vaping time will last longer than the F(t) and Pulse mode. -
VV: Variable Voltage Mode
In the Variable Voltage(VV) mode, the output mode of the device will change from adjustable power output to adjustable voltage output, and the display units is voltage. You can adjust it according to the coil resistance and the required voltage. -
THEMES: Themes Selection
You can choose your theme for your preference. -
Setting: SYSTEM SET
System setting includes Smart ON/OFF, Puffs, Brightness, LED Lights ON/OFF, and Default options.- SMART ON/OFF: when this function is on and a TANK is installed, the system will recommend the best power automatically. Under the F(t), Pulse, ECO mode, press “DOWN” and power button simultaneously, the smart function can be switch on or off. (PS: THE SMART FUNCTION WORKS IN THE GTI COIL PLATFORM!)
- Puffs: The 5-day puff counter can be checked in this interface, also the puff can be cleared after confirming the reset option.
PROTECTIONS
-
Short circuit protection & Low resistance protection:
When the load resistance is less than 0.1 Ω, press the ignition key devise will enter the short circuit protection and close the output, screen will display “SHORT ATOMIZER”. -
Low resistance protection:
When the load resistance is less than 0.1 Ω, press the ignition key devise will enter the Low resistance protection and close the output, screen will display “LOW RESISTANCE”. -
No load protection:
When no load resistance is detected, press power button could trigger the no load protection, the device will close the output, at the same time OLED display will show “CHECK ATOMIZER”. -
High resistance protection:
When the load resistance is larger than 5Ω, press power button could trigger the high resistance protection, the device will close the output, at the same time OLED display will show “ CHECK ATOMIZER ”. -
Low voltage protection:
When the voltage of the battery cell is lower than 3.3V, press power button could trigger the low voltage protection, the device will close the output, at the same time OLED display will show “BATTERY LOW”. -
PCBA(Printed Circuit Board Assembly):
When the temperature of PCBA sensor reaches 60-75 degrees, screen display “OVER HEAT” and output is closed. -
Over discharge protection:
During the charging, the battery voltage will rises to 4.1V+/-0.05V,the screen will display “100%” -
USB High Voltage Input Protection:
Switching in the charger, stop charging when the input voltage to USB port exceeds 6V and is lower than 30V. -
Over charge protection:
During the charging, the battery voltage will rises to 4.2V+/-0.3V,the screen will display “100%” -
Auto-shut off protection
When POWER button is held for 10±1 seconds, the device will close the output, at the same time OLED display will show “OVER TIME”.
Frequently Asked Questions
Q: How can I adjust the airflow?
To adjust the airflow volume, rotate the air-inlet ring on the top of the tank.
Q: How do I charge the battery?
After connecting the Type-C cable to the battery, the battery indicator and remaining charging time will be shown on the screen.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>