Led2 2250631D Bathroom Ceiling Light User Manual
- July 20, 2024
- Led2
Table of Contents
Led2 2250631D Bathroom Ceiling Light
Product Information
Specifications
- Model: LED2 dx
- Dimming Function: DALI 2 with PUSH dimming
- Control: DALI bus or DALI dimmer
- Installation: 4-5 wires for DALI, 3-4 wires for PUSH
- Maximum PUSH Cable Length: 15m
- Groups Control: Up to 16 groups with 64 luminaires
Product Usage Instructions
DALI Dimming
To dim, save, and recall the LED2 dx luminaire using the DALI bus or DALI dimmer:
- Connect the luminaire with a 4-5 wire installation following DALI installation rules.
- Use the DALI bus to control up to 64 luminaires in 16 groups.
PUSH Dimming
- To dim the lamp using the 1/0 button with PUSH dimming functionality
- For PUSH dimming, connect the lamp with a 3-4 wire installation as shown in pic. 2.
- Warning: The maximum total length of the PUSH cable should not exceed 15m. Resynchronize by holding the button for 10 if the luminaires are out of sync.
FAQ
Q: What should I do if my luminaires are out of sync when using PUSH dimming?
A: To resynchronize, hold down the button for 10 seconds to ensure all luminaires are dimmed uniformly.
INTRODUCTION
- The luminaire is equipped with an internal DALI 2 dimmable ballast with a PUSH dimming function using the 1/0 button
- LED2 xxxxxxxD luminaire can be dimmed, saved, and recalled using the DALI bus or DALI dimmer.
- Using the DALI bus, it is possible to control 64 luminaires in 16 groups. A 4-5 wire installation is required. It is necessary to observe the DALI installation rules pic. 3.
- LED2 xxxxxxxDTW luminaire can be dimmed, set the chromaticity temperature, and save and recall scenes using the DALI bus with the DT8 protocol. Using the DALI bus, it is possible to control 64 luminaires in 16 groups. A 4-5 wire installation is required.
- It is necessary to follow the rules of DALI installation. Wiring diagram pic. 3. Some luminaires support PUSH tunable white. For availability, see the specification of the luminaire (DALI TW/PUSH TW) on the led2.eu website.
- A 3-4 wire installation is required pic. 2. LED2 xxxxxxxD lamp can be dimmed using the button marked 1/0. A 3-4 wire installation is required pic. 2.
PUSH dimming functions
- On/off: short press 0.1-0.5 s.
- Dimming: press and hold for 0.6-9 s.
- Dimming up or down: each time you press and hold, the dimming will change direction.
- PUSH TW (only available for some DTW models): quickly press the button twice to call up the tunable white function. Hold the button to change CCT.
- To return to the dimming function, quickly press the button twice again.
- Built-in memory: the light will return to the previous dimming level when turned off and on again, even after a power failure.
- Reset PUSH: Hold the button for more than 10 s.
- Warning! The maximum total length of the PUSH cable must not exceed 15m. When several luminaires are connected and the button is briefly pressed, the luminaires may become out of sync.
- To resynchronize, it is necessary to hold down the button for ＞10 s. Dimming time between min. and max. may vary between models and the same dimming time cannot be guaranteed.
- www.led2.eu
- info@led2.eu
- 83104 tel.+421918508500
Documents / Resources
| Led2
2250631D Bathroom Ceiling
Light
[pdf] User Manual
2250631D Bathroom Ceiling Light, 2250631D, Bathroom Ceiling Light, Ceiling
Light, Light
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>