3onedata IES208-4F Unmanaged Industrial Ethernet Switch Installation Guide

July 25, 2024
3onedata

IES208-4F
Unmanaged Industrial Ethernet Switch
Quick Installation Guide

3onedata Co., Ltd.
Address: 3/B, Zone 1, Baiwangxin High Technology
Industrial Park, Xili, Nanshan District, Shenzhen
Website: www.3onedata.com
Tel: +86 0755-26702688
Fax: +86 0755-26703485

【Package Checklist】

Please check the integrity of package and accessories while first using the switch.

  1. Industrial Ethernet
  2. DIN-Rail mounting switch attachment
  3. Certification
  4. Warranty card

If any of these items are damaged or lost, please contact our company or dealers, we will solve it ASAP.

【Product Overview】

This product is 8-port 100M unmanaged DIN-Rail industrial Ethernet switch. The model is IES208-4F (4 100M copper ports + 4 100M fiber ports, 12~48VDC redundant power supply input)

【Panel Design】

Top view, bottom view and rear view
Main view and right view

  1. Grounding screw
  2. Relay alarm output terminal block (Reserved)
  3. Console port (Reserved)
  4. Power input terminal (PWR1, PWR2)
  5. DIP switch (Reserved)
  6. Wall-mounting location hole
  7. DIN-Rail mounting kit
  8. Power indicator (P1, P2)
  9. 100Base-FX 100M fiber port (5-8)
  10. 10/100Base-T(X) 100M copper port (1-4)
  11. Ethernet port indicator(1-8)

【Mounting Dimension】

Unit: mm Notice Before Mounting:
Don’t place or install the device in area near water or moist, keep the relative humidity of the device surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power supply specification to avoid over-voltage damaging the device.
The device surface temperature is high after running; please don’t directly contact to avoid scalding.

【DIN-Rail Mounting】

The product adopts 35mm standard DIN-Rail mounting which is suitable for most industrial scenes, mounting steps as follows:
Step 1
Check if the DIN-Rail mounting kit is installed firmly.
Step 2
Insert the bottom of DIN-Rail mounting kit (one side with spring support) into DIN-Rail, and then insert the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert to the top.
Step 3
Check and confirm the product is firmly installed on DIN-Rail, then mounting ends.

【Disassembling DIN-Rail】

Step 1
Power off the device.
Step 2
After lifting the device upward slightly, first shift out the top of DIN-Rail mounting kit, and then shift out the bottom of DIN-Rail, disassembling ends.
Notice before power on:

  • Power ON operation: First insert the power supply terminal block into the device power supply interface, then plug the power supply plug contact and power on.
  • Power OFF operation: First, remove the power plug, then remove the wiring section of terminal block. Please pay attention to the above operation sequence.

【Power Supply Connection】

DC dual power supply
Provide 4-pin 7.62mm pitch power supply input terminal blocks and support two independent DC power supply systems, PWR1 and PWR2, which supports non- polarity function, that the devicecan work normally after reverse connection. Voltage range: 12~48VDC.

【Checking LED Indicator】

Provide LED indicators to monitor its operating status, which has simplified the overall troubleshooting process. The function of each LED is described in the table below:

LED Indicate Description
P1/P2 ON Power is connected and running

normally
OFF| Power supply is disconnected or running abnormally
Link/Act
(1-8)| ON| Ethernet port has established a valid network connection
Blinking| Ethernet port is in an active network status
OFF| Ethernet port has not established valid network connection

【Specification】

Panel|
---|---
100M copper port| 10/100Base-T(X), R345, Automatic Flow Control, Full/half Duplex Mode, MDI/MDI-X Autotunning
100M fiber port| 100Base-FX, optional SC/ST/FC
Console port| Reserved
Relay alarm Reserved|
Indicator| Power supply indicator, interface indicator
Switch Property|
Backplane bandwidth| 2G
Packet buffer size| 1Mbit
MAC Address Table| 2K
Power supply|
Input power supply| 12-48VDC, dual power supply redundancy, support
non-polarity
Access terminal block| 4-pin 7.62mm pitch terminal blocks
Power Consumption|
No-load| 4.93W@12VDC
Full-load| 6.40W@12VDC
Working Environment|
Working temperature| -40-75
Storage temperature| °C -40-85
Working humidity| °C 5%–,95% (no condensation)
Protection grade| IP40 (metal shell)

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

3onedata User Manuals

Related Manuals