ATEN CS1922M 4-Port USB 3.0 4K DisplayPort MST KVMP Switch User Guide
- July 16, 2024
- Aten
Table of Contents
ATEN CS1922M 4-Port USB 3.0 4K DisplayPort MST KVMP Switch
Hardware Overview
Installation
To prevent damage to your installation from power surges or static electricity, all connected devices must be properly grounded.
Package Contents
CS1922M
- 1 2-Port USB 3.0 4K DisplayPort
- MST KVMP™ Switch
- 2 DisplayPort cables
- 2 USB 3.0 cables
- 4 audio cables
- 1 power adapter
- 1 user instructions
CS1924M
- 1 4-Port USB 3.0 4K DisplayPort
- MST KVMP™ Switch
- 4 DisplayPort cables
- 4 USB 3.0 cables
- 8 audio cables
- 1 power adapter
- 1 user instructions
Operation
Hardware Overview
Front View
- port selection pushbuttons
- port LEDs
- audio jacks
- USB 3.0 hub
Rear View
- KVM ports
- console ports
- USB 3.0 hub
- power jack
Installation
-
Plug the USB keyboard and mouse into the console ports on the rear panel.
-
Plug the monitor into the DisplayPort or the HDMI console port and power on the monitor.
-
Plug the main microphone and speakers into the microphone and speaker audio jacks on the front panel.
-
(Optional) Plug the secondary microphone and speakers into the console audio jacks on the rear panel. The front panel jacks have priority over those on the rear panel.
-
Using the cables provided with this package, plug the DisplayPort, USB 3.0, microphone, and speaker connectors into their corresponding ports in the KVM port section of the switch.
-
At the other ends of the cables, plug the USB 3.0, DisplayPort, microphone, and speaker connectors into their respective ports on the computer
-
(Optional) Plug USB peripherals into the USB Type-A sockets located on the front panel and in the rear panel’s console port section.
-
(Optional) Plug an RJ-11 to DB9 cable from the RJ-11 port to a computer’s serial port for RS-232 control.
Note: The RJ-11 to DB9 cable is sold separately. Please contact your ATEN dealer for product information. -
Plug the power adapter (provided with this package) into the switch’s power jack and then plug the other end into an AC power source.
-
Power on the computers.
Operation
There are four convenient methods to switch between the computers: Manual – by
pressing the port selection pushbuttons on the front panel, Mouse – by
clicking the scroll wheel of the mouse, Hotkeys – by entering combinations on
the keyboard, and RS-232 commands – for more information on the RS-232
commands, please refer to the user manual.
Manual Switching
For manual port selection: Press a front panel port selection pushbutton once
to bring the KVM, audio, and USB focus to the computer attached to the
corresponding port.
Mouse Switching
For mouse port selection: Double-click the scroll wheel of your USB mouse to
cycle through the ports.
Note
- Mouse switching is only supported by USB 3-key scroll wheel mice.
- Mouse switching is disabled by default. See the Hotkey Setting Mode section for how to enable mouse switching.
- Mouse switching is only supported when Mouse Emulation is enabled.
Hotkey Switching
Cycling Through the Ports
Going Directly to a Port
Hotkey Setting Mode (HSM)
Hotkey Setting Mode is used to set functions on the switch. Invoke HSM and
then press a key to perform the corresponding function. For more information
on the HSM, please refer to the user manual.
To invoke HSM, do the following
- Press and hold the [Num Lock] key.
- Press and release the minus [-] key.
- Release the [Num Lock] key
Support and Documentation
Notice All information, documentation, firmware, software utilities, and
specifications contained in this package are subject to change without prior
notification by the manufacturer. To reduce the environmental impact of our
products, ATEN documentation and
software can be found online at http://www.aten.com/download/
Technical Support
www.aten.com/support
Scan for more information
The terms HDMI, HDMI High-Definition
The Multimedia Interface and the HDMI Logo are trademarks or registered
trademarks of HDMI Licensing Administrator, Inc.
Copyright 2024 ATEN® International Co. Ltd.
ATEN and the ATEN logo are registered trademarks of ATEN International Co.,
Ltd. All rights reserved. All other trademarks are the property of their
respective owners. Part No. PAPE-1223-I90G Released: 05/2024
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>