HUANUO HNSS7 Single Monitor Arm Instruction Manual

HUANUO HNSS7 Single Monitor Arm

INSTRUCTION MANUAL
Rev02(A)
HNSS7

Desk Monitor Arm
1-8044-808-0-556196–05333 874(UK) )
support@huanuo.com

Before getting started, let’s make sure this mount is compatible.

Product Features

TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MONITOR INSTALLATION

Attention
DO NOT adjust tension without monitor attached.

1. Verify the weight of your monitor (including accessories) is between 4.4-26.4 lbs (2-12kg). Monitor weight information can be found in the monitor instruction manual or by contacting the manufacturer.
2. Ensure monitor has been securely attached to the mount.

WARNING:

• Gas spring arm is under pressure and should be handled with care.
• Failure to follow the instructions may result in damage to the mount and/or personal injury.

Supplied Parts and Hardware for Step 1

Supplied Parts and Hardware for Step 2

Supplied Parts and Hardware for Step 3

Supplied Parts and Hardware for Step 4

Supplied Hardware for Step 5

Step 1 Attach the USB Cable

Step 2 Install the Base

Option B: For Grommet Mounting

Step 3 Attach the Lower and Upper Arm Sections
Attach the lower and upper arm sections [05] and [06], then tighten the set screws. Do not overtighten them, as this may affect the rotation of the arm.

Step 4 Attach the Monitor Plate to the Upper Arm Section
Slide the monitor plate [07] sideways into the slot at the end of the upper arm section [06]. Fasten with bolt [01] and washer [02].

Step 5 Hang the Monitor on the Mount
Hand thread bolts into the threaded inserts on the back of your monitor to determine which bolt (M4 x 12mm or M4 x 30mm) to use. A minimum of 4-5 turns into the threading is required. Do not turn past the bottom of the hole.

Choose the bolt and spacer configuration that fits your monitor type. Thread in the top bolts, but do not tighten all the way yet.

With the top bolts attached, hang the monitor onto the VESA plate using the to 1 00mm slots or 75mm holes. Thread in the bottom bolts, then firmly tighten all bolts to secure the monitor to the mount arm.

NOTE: Gas spring tension is preset at 8.8-11 lbs (4-5kg).
After hanging the monitor on the mount, release the monitor slowly so that it doesn’t suddenly fall.

• For VESA hole pattern:
  • 75 x 75mm (3 x 3″)
  • 100 x 100mm (3.9 x 3.9″)

Step 6 Adjust Gas Spring Tension

1. Hold the upper arm in a horizontal position. In this position, you can access the gas spring tension bolt to increase or decrease tension so the arm stays in position by itself.

2. Use the large Allen key to adjust gas spring tension until the arm stays in position by itself. Once correctly adjusted, you can raise and lower your monitor and it will stay in position.

   • If the monitor falls down and fails to stay at the desired height:
     Turn counter-clockwise (+) to increase gas spring tension until the monitor can stay at the desired height by itself.

   • If the monitor rises up and fails to stay at the desired height:
     Turn clockwise (-) to reduce gas spring tension until the monitor can stay at the desired height by itself.

Step 7 Adjust the Swivel Position of the Monitor
Swivel the monitor to your desired position.

Swivel the monitor to your desired position.
Adjust your monitor by gripping the monitor edges (do not press on the screen itself). If it’s difficult to adjust, loosen the tilt-lock bolt on the monitor plate connector. Adjust the monitor to the desired angle, and then fully tighten the bolt again to lock the tilt angle.

Step 9 Adjust the Rotation of the Monitor

Step 10 Route Cables Down the Arm

• 1- 800-556-0533(US/CA)
• 44- 808-196-3874(UK)
• support@huanuo.com
• www.huanuo.com

860-00474-00 Rev02

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>