HUANUO HNSSK4 Adjustable Single Monitor Stand with Gas Spring Arm Instruction Manual
- June 6, 2024
- HUANUO
Table of Contents
- HUANUO HNSSK4 Adjustable Single Monitor Stand with Gas Spring Arm
- IMPORTANT SAFETY INFORMATION
- Check the VESA Pattern of Monitor Before the Installation
- Product Features
- TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION
- Supplied Parts and Hardware
- Supplied Parts and Hardware
- Supplied Hardware
- Clamp Mounting
- Grommet Mounting
- Level and Rotation Adjustments
- Technical Support
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
HUANUO HNSSK4 Adjustable Single Monitor Stand with Gas Spring Arm
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you do not understand the instructions or have any concerns or questions, please contact our Technical Support line at 1-800-556-0533 or customer service at support@huanuoav.com.
- Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.
- This product contains a high-pressure gas spring, fire, and percussion is prohibited. Also, it is strictly prohibited to dismantle without professionals. Please return to the manufacturer or hand over to professional agencies if the product is abandoned.
- The desk must be capable of supporting three times the weight of the total load (the mount, the monitor, and all accessories weight). Don’t use the product on particle board.
- Before starting assembly, verify all parts are included and undamaged. Do not use damaged or defective parts. lf you require replacement parts, contact our Technical Support line at 1-800-556-0533 or customer service at
support@huanuoav.com.
Please note: Not all parts and hardware included in this package will be used.
Check the VESA Pattern of Monitor Before the Installation
- Minimum VESA Pattern: 3 in./75mm(W) x 3 in./75mm(H)
- If your Monitor VESA is greater than 100 x 100 mm/4 x 4 in. or less than VESA 75 x 75 mm/ 3 x 3 in., this mount is NOT compatible.
Product Features
TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION
Warning
Do not adjust tension without a monitor.
- Ensure the monitor has been attached to the mount.
- Read your monitor box or manual to find out monitor net weight.
- Ensure the net weight of the monitor (including accessories) is within 17.6 Ibs (8 kg).
Supplied Parts and Hardware
Step 1
Supplied Parts and Hardware
Step 2
Supplied Hardware
Step 3-
Clamp Mounting
Step 1A
- Connect Connecting Plate [B] to Arm [A]
- Secure Desk Clamp [C] to Connecting Plate [B] According to the Thickness of the Desktop
- 1A-3 Secure the Mount Assembly to Desktop
Grommet Mounting
- Secure Bottom Plate [F] and Bolt [H] to Arm [A]
- 1B-2 Secure the Mount Assembly to the Desktop
Step 2 Attach the Monitor Plate [K] to the Monitor
Select Monitor Bolts
- Only one bolt size fits your monitor
- M4x12mm
- M4x30mm
- Option A [Flat Back Monitor (Universal Monitor Plate)]
- Option B [Round Back Monitor (Universal Monitor Plate)]
Step 3 Secure the Monitor to Arm Assembly
The tension is preset at 4-5kg. After hanging the monitor to the mount, please release the monitor slowly to prevent it from falling suddenly
CAUTION:
HEAVY! You may need assistance with this step.
Step 4 Adjust the Gas Spring Tension
Be sure to keep the arm in horizontal position during adjustment. Or else, it would be difficult to adjust the mount or damage the mount.
- If the monitor can stay at the desired height by itself, no adjustment needed.
- If the monitor rises up, press the arm to keep it in horizontal position and then use the 13/64in. (5mm) Alley key [M] to turn the bolt clockwise(“-” direc-tion) to reduce tension of the arm only until the monitor can stay at the desired height by itself.
- If the monitor falls down, lift the arm to keep it in horizontal position and then use the 13/64in. (5mm) Alley key [M] to turn the bolt counter-clockwise(“+” direction) to increase tension of the arm only until the monitor can stay at the desired height by itself.
Step 5 Rotation Restriction
Step 6 Adjustments
Tilt Adjustment
“+” Clockwise: Tighten
“-” Counter-clockwise: Loosen
Situation 1: If the monitor can stay at the desired tilt angle by itself,
no adjustment is needed.
Situation 2: If the monitor can not stay at the desired tilt angle by
itself, turn the bolt clockwise or counter-clockwise as shown until the
monitor can stay at the desired tilt angle by itself.
Level and Rotation Adjustments
If needed, the TV can be leveled and rotated 360 degree
Step 7 Route the Cables Along the Arm [A]
-
Detach the cable covers from the arm [A]
Note: Loosen the preassembled bolts from the covers, then pinch both sides of the bottom end of the cable covers to make it detach from the arm -
Route the cables along the arm and secure the cable covers to the arm [A]
Note: Pinch both side of the bottom end of the cable cover to make it attach to the arm, then fasten the bolt to secure the cover to the arm.
All of us at HUANUO do appreciate your product purchase. We hope that you are as happy with your product as we designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. Please share your experience of our product with others at www.huanuoav.com/reviews if you are satisfied. If you have any questions please don’t hesitate to contact us at
Technical Support
1-800-556-0533 Mon-Fri 10am – 5pm (PST) (USA) (CAN)
Other Info
support@huanuoav.com (US/CA)
Please check www.huanuoav.com for more products and
company information.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>