HUANUO HNSS12 Monitor Desk Mount Instruction Manual
- June 7, 2024
- HUANUO
Table of Contents
Monitor Desk Mount
Instruction Manual
V4.0
Website: www.huanuoav.com
Thank you for choosing this HUANUO product! At HUANUO we strive to provide you
with the best quality products and services in the industry. Please share your
experience of our product with others at
www.huanuoav.com/reviews if you are
satisfied. Should you have any issues, please don’t hesitate to contact us.
Technical Support:
1-800-556-0533 Mon-Fri 10am – 5pm (PST)
(USA) (CAN)
Other Info:
support@huanuoav.com (US/CA)
support_eu@huanuoav.com (DE/UK/FR/IT/ES/AU)
support_jp@huanuoav.com (JP)
IMPORTANT SAFETY INFORMATION
Please carefully read all instructions before attempting installation. If you
do not understand the instructions or have any concerns or questions, please
contact our Technical Support line at
1-800-556-0533 or customer service at
support@huanuoav.com
CAUTION : Avoid potential personal injuries and property damage!
- Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. We are not liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
- This product contains a high-pressure gas spring, fire and per are strictly prohibited to dismantle without professionals. Please return to the manufacturer or hand it over to professional agencies if the product is abandoned.
- The desk must be capable of supporting three times the weight of the total load (the mount, the monitor, and all accessories weight). Don’t use the product on particleboard.
Weight Restrictions
If your monitor weighs more, this mount is
NOT compatible.
WARNING
DO NOT exceed the maximum weight indicated.
This mounting system is intended for use only within the maximum weights
indicated. Use with products heavier than the maximum weights indicated may
result in failure of the mount and its accessories, causing possible damage
and or injury.
Check the VESA Pattern of Your Monitor before You Begin the Installation
If your Monitor VESA is greater than 100×100 mm/4×4 in. or less than VESA
75x75mm/3x3in., this mount is NOT compatible.
If this desk mount is NOT compatible, please contact customer service
atsupport@huanuoav.com to find a compatible
product.
Product Features
TENSION ADJUSTMENT SHOULD BE DONE ONLY AFTER MOUNT INSTALLATION
Do not adjust tension without a monitor.
- Ensure monitor has been attached to the mount.
- Read your monitor box or manual to find out monitor net weight.
- Ensure the net weight of the monitor (including accessories) is between 4.4~26.5 Ibs (2-12 kg).
Clockwise to reduce tension(carry less weight)
Counter-clockwise to increase tension(carry more weight)
Tools Needed (Not included)
Supplied Parts and Hardware
Warning: This product contains small items that could be a choking hazard
if swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, contact our
customer service at support@huanuoav.com.
- Please note: Not all hardware included in this package will be used.
Supplied Parts and Hardware for Step 1
Supplied Parts and Hardware for Step 2
Supplied Parts and Hardware for Step 3
Supplied Parts and Hardware for Step 4
Supplied Hardware for Step 5 and Step 7
Supplied Part for Step 8
1. Install the Base
A. For Clamp Mounting
B. For Grommet Mounting
If there is no grommet hole on your desk, position the base [03] on the mounting surface and mark the hole. Drill a hole using the drill bit in a diameter of 0.4 in.(10mm) – 2 in.(50mm) at the marked position through the mounting surface.
2. Install the Arm and Arm Extension to Base
3. Install the Monitor Plate to Arm
4. Attach Monitors to the Arm
5. Adjust Gas Spring Tension
Be sure to keep the arm in a horizontal position during adjustment. Or else, it would be difficult to adjust the amount or damage the mount.
- If the monitor can stay at the desired height by itself, no adjustment is needed.
- If the monitor rises up, press the arm to keep it in horizontal position and then use the Large Allen Key (E) to turn the bolt clockwise(“-” direction) to reduce the tension of the arm only until the monitor can stay at the desired height by itself.
- If the monitor falls down, lift the arm to keep it in horizontal position and then use the Large Allen Key (E) to turn the bolt counter-clockwise(“+” direction) to increase the tension of the arm only until the monitor can stay at the desired height by itself.
6. Rotation Restriction
7. Tilt Adjustment
Adjust monitor to proper tilt angle. Use Allen key (E) to tighten the bolt and fix tilt angle
8. Route Cables along the Arms
9. Attach the Decorative Cover to C-Clamp
Warm Tips: The decorative cover [04] can only be used for the C-Clamp.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>