HUANUO CPU Holder Under Desk Mount Wall Mount Instruction Manual

HUANUO CPU Holder Under Desk Mount Wall Mount

Thank you for choosing this HUANUO product! At HUANUO we strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us at Technical Support: 1-800-556-0533 Mon-Fri 8 am – 8 pm (CST) Other Info: support@huanuoav.com (US/CA).

IMPORTANT SAFETY INFORMATION

• Please read through these instructions completely before attempting installa­tion. If you do not understand the instructions or have any concerns or questions, please contact our Technical Support line at 1-800-556-0533 or customer service at support@huanuoav.com.
• Check package contents against Supplied Parts and Hardware List to that all components were received undamaged. Do not use damaged or assure defective parts. If you require replacement parts, please contact our Technical Support line at 1-800-556-0533 or customer service at support@huanuoav.com.
• Not all parts and hardware included will be used.
• Do not use this product for any purpose or in any configuration not specified in this instruction. We hereby disclaim any liability for injury or explicitly damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.

Tools Needed (Not Included)

Supplied Parts and Hardware List

Step 1 Attach the Pads [E] to the CPU Holder [A]

Step 2 Adjust the Height of the CPU Holder [A]

CAUTION:
TO AVOID ANY DAMAGE, PLEASE TAKE OFF CPU 1 BEFORE MAKING A HEIGHT ADJUSTMENT

1. Loosen the preassembled bolt [H1].
2. Pull out and hold the bolt [H2].
3. Adjust the height of the CPU holder [A].

Fasten the bolt [H1] and release the bolt [H2] to fix the CPU holder [A] in place.

Note:
the height of the CPU holder [A] should be greater or equal to that of the CPU.

Step 3 Secure CPU Holder

Step 3a For Desk Installation Option
Secure CPU Holder [A] to the Bottom of Desk Using Screws [B] and Washers [F].

Step 3b For Wood Stud Installation Option

• Step 3b-1 Position the CPU holder [A] at your desired height. Level the CPU holder and mark the four holes.

• Step 3b-2 Drill 4 pilot holes using a 1 /8 in (3 mm) diameter drill bit. Make sure the depth is not less than 0.6 in (15mm). Secure the two screws [B] into the two top holes.

• Step 3b-4 Secure the CPU holder [A] using the other two screws [B]

• Step 3b-3 Hang the CPU holder [A] to the screws [B]

Step 3c For Concrete Wall Installation Option

• Step 3c-1 Position the CPU holder [A] at your desired height. Level the CPU holder and mark the four holes.
• Step 3c-2 brill 4 pilot holes using a 1 / 4 in (6 mm) diameter drill bit. Make sure the depth is not less than 1.6 in (40mm). Knock anchors [D] into the wall. Secure the two screws [C] into the top two anchors [D].
• Step 3c-4 Secure the CPU holder [A] to the concrete wall using the other two screws [C]
• Step 3c-3 Hang the CPU holder [A] to the screws [C]

Step 4 ut CPU into the CPU Holder

Step 4-1 Loosen the Knobs [K] to Increase the Width of the CPU Holder [A], Then Put CPU into the CPU Holder [A].

Step 4-2 Adjust the Width of CPU Holder [A] According to the Width of the CPU, Then Tighten the Knobs [K].

Thank you again for choosing this HUANUO product

All of us at HUANUO do appreciate your product purchase. We hope that you are as happy with your product as we designing and manufacturing it for you. We strive to provide you with the best quality products and services in the industry. If you have any questions please don’t hesitate to contact us at Technical Support: 1-800-556-0533 Mon- Fri 8am – 8pm (CST) Other Info: support@huanuoav.com (US/CA).

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>