FLASH F7100548 LED Moving Head 6x15W User Manual

: July 14, 2024
: FLASH

Table of Contents

FLASH F7100548 LED Moving Head 6x15W
Product Usage Instructions
INTRODUCTION
PRODUCT INFORMATION
INSTALATION
Voltage Specification
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FLASH F7100548 LED Moving Head 6x15W

Specifications

Light source: 6x15W OSRAM RGBW 4in1
Number of DMX channels: 11/16
IP Rating: IP20
Housing type: ABS
Cooling: Active
AC IN/OUT: PowerCon
3-Pin XLR DMX Input/Output
Net weight: 4.1 kg
Dimensions: H(25)xW(21.5)xD(23)cm

Product Usage Instructions

Installation

Unpack and carefully inspect the fixture for any transportation damage before proceeding with installation.
Ensure the fixture is securely fastened to a surface or rigging hardware to prevent any movement when in operation.

Connection

Use 2 clamps to rig the fixture, ensuring both clamps are securely fastened with 1/4-turn fasteners turned a full 900 clockwise.
When clamping the fixture to a truss or structure at an angle, use two half-coupler type clamps that completely encircle the structure when fastened.

DMX Chart
Refer to the provided DMX chart for detailed information on channel assignments and control settings.

Safety Precautions

Do not expose the front lens of the fixture to direct sunlight or strong light sources to prevent potential fire hazards.
Avoid pointing strong light output from other fixtures directly at the LED Moving Head to prevent damage.
Disconnect main power before servicing or maintenance procedures.

FAQ

Q: What should I do if I encounter a serious operating problem with the fixture?
- A: Stop using the fixture immediately and do not attempt to repair it yourself. Contact the nearest authorized technical assistance center for professional help.
Q: Can I connect the fixture to a dimmer pack?
- A: No, do not connect the device to any dimmer pack as it may lead to damage or malfunction.

LED Moving Head
6x15W OSRAM RGBW 4in1
KALEIDOSKOPE Big-EYE

User Manual

WARNING! The Led Moving Head (LMH) has a powerful pan and tilt motor. The torque reaction when the head is panned suddenly can cause the base to move if the fixture is standing unsecured on a surface. Do not apply power to the LMH unless the baase is securely fastened to a surface or to rigging hardware.
WARNING! Use 2 clamps to rig the fixture. Do not hang the fixture from only one clamp. Lock each clamp with both 1/4-turn fasteners. Fasteners are locked only when turned a full 900 clockwise.
WARNING! When clamping the fixture to a truss or other structure at any other angle than with the yoke hanging vertically downwards, use two clamps of half-coupler type. Do not use any type of clamp that does not completely encircle the structure when fastened.
WARNING! Position or shade the head so that the front lens will not be exposed to sunlight or any other strong light source from any angle – even for a few seconds. See Figure 1. The LMH lens can focused the sun’s rays, creating a potential fire hazard and causing damage.
IMPORTANT! Do not point strong light output from other fixtures at the LMH, as intense illumination can damaged the display. $FLASH-F7100548-LED- Moving-Head-6x15W-IMAGE $4$$

INTRODUCTION

THANK YOU FOR PURCHASING 6x15W OSRAM. FOR SAFETY RE-ASONS AND TO ENSURE THE TROUBLE-FREE OPERATION, CARE-FULLY READ THE INSTRUCTIONS.

SAFETY INFORMATION

Please keep this User Manual for future consultation. If you sell the fixture to another user, be sure that they also receive this instruction booklet.
Unpack and check carefully the-re is no transportation damage be-fore using the fixture.
Before operating, ensure that the voltage and frequency of power supply match the power requirements of the fixture.
It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.
Disconnect main power before servicing and maintenance.
Use safety chain when fixes this fixture. Don’t handle the fixture by taking its head only, but always by taking its base.
Maximum ambient temperature is: 40°C Don’t operate it where the temperature is higher than this.
In the event of serious operating problem, stop using the fixture immediately. Never try to repair the fixture by your-self.
Repairs carried out by unskilled people can lead to damage or malfunction. Please contact the nearest authorized technical assistance center. Always use the same type spare parts.
Do not connect the device to any dimmer pack.
Do not touch any wire during operation and there might be a hazard of electric shock.
To prevent or reduce the risk of electrical shock or fire, do not expose the fixture to rain or moisture.
The housing must be replaced if they are visibly damaged.
Do not look directly at the light spot while the fixture is on.

PRODUCT INFORMATION

Light source : 6x15W OSRAM RGBW 4in1
Power consumption: 100W
Power supply voltage : 100-245V, 50/60Hz AC
PAN range of motion : 540°
TILT range of motion : 220°
Operating modes : DMX512, Manual, Auto, Sound-controlled, Master/Slave
Number of DMX channels : 11/16
IP Rating : IP20
Housing type : ABS
Cooling : Active
AC IN/OUT : PowerCon
3-Pin XLR DMX Input/Output Net weight: 4.1 kg
Dimensions : H(25)xW(21.5)xD(23)cm

INSTALATION

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s weight. Also always use a safety cable that can hold 12 times of the weight of the unit when installing the fixture. The equipment must be fixed by professionals. And it must be fixed at a place where is out of the touch of people and has no one pass by or under it.
Regardless of the rigging option you chose for our fixture, always be sure to secure your fixture with safety cable. The fixture provides a bulletin rigging point for a safety cable on the hanging bracket as illustrated above. Be sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle.

The package includes
The following items are included

1- Moving head (1 pc.)
2 – Power cable type power CON (1 pc.)
3- Mounting clamp (1 pc.)
4- Owner’s manual (1 pc.)

CONNECTION
The device is equipped with the following interfaces

DMX (in/out): XLR 3(5)-pin socket
Power (in/out): power CON socket
The connection is performed using cable with XLR-female -> XLR-Male plugs.

CAUTION! At the last fixture, the DMX signal has to be terminated with a terminator. Solder a 120Ω resistor between signal (-) and si-gnal (+) into a XLR plug and plug it in the DMX output of the last fixture.

$FLASH-F7100548-LED-Moving-Head-6x15W-IMAGE $7$$

IMPORTANT! The maximum number of devices connected in series via power cable is 10 pcs.

The connection is performed using power cable with powerCON connector (included). The device must be operated by qualified personnel.

CAUTION! In the case of cable damage do not attempt to repair. Replacement or repair can be made only on the manufacturer or by a person with appropriate permissions
Using lamp, the change rate of power voltage should be within ±10%, if the voltage is too high, it will shorten the light’s life; if it’s not enough, the lamp will be dark. Please restart it after turning off light for 20 mi-nutes until full-cooling. Frequent switching will reduce the life span of lamps and bulbs; intermittent using will improve the life of bulbs and lamps.