FORTIN EVO Immobilizer Bypass Module Installation Guide
- July 13, 2024
- FORTIN
Table of Contents
FORTIN EVO Immobilizer Bypass Module
Product Information
- Product Name: Immobilizer Bypass System
- Compatible Vehicles: Mitsubishi Mirage 2014-2019, Mirage G4 2017-2019
- F irmware Version: 86.[16]
REGULAR INSTALLATION
ADDENDUM – SUGGESTED WIRING CONFIGURATION
To add the firmware version and the options, use the FLASH LINK UPDATER or
FLASH LINK MOBILE tool, sold separately.
Program bypass option
IF THE VEHICLE IS NOT EQUIPPED
WITH FUNCTIONAL HOOD PIN:
Program bypass option
(If equiped with OEM alarm):
Parts required (Not included)
- 1X fuse
MANDATORY INSTALL
HOOD PIN
- HOOD STATUS: THE HOOD PIN SWITCH MUST BE INSTALLED IF THE VEHICLE CAN BE REMOTE-STARTED WITH THE HOOD OPEN, AND SET FUNCTION A11 TO OFF.
Notice: the installation of safety elements are mandatory. The hood pin is an essential security element and must be installed.
THIS MODULE MUST BE INSTALLED BY A QUALIFIED TECHNICIAN. A WRONG CONNECTION CAN CAUSE PERMANENT DAMAGE TO THE VEHICLE.
Specifications
- F eatures: Immobilizer bypass, Lock/Unlock, Arm/Disarm, Tachometer, Parking Lights, Door Status, Trunk Status, Hood Status, Hand-Brake Status, Foot-Brake Status
- Unit Option: A11 (Hood trigger output status)
- Parts Required: 1X Fuse (not included)
Installation Instructions
- Mandatory Installation: Hood pin contact must be installed for proper functionality.
- Function A11 Setting: If the vehicle does not have a functional hood pin, set function A11 to OFF.
- Warning: This module must be installed by a qualified technician to avoid permanent damage to the vehicle.
Wiring Instructions
Refer to the provided wiring diagram for proper connections.
- Positive Connections: Parking Lights, 12V, Ignition, Accessory, Starter, Tachometer, Foot Brake
- Negative Connections: Unlock, Clutch, Hand Brake, Ground While Running, Trunk, Door, Lock
This guide may change without notice. See www.fortin.ca for latest version.
DESCRIPTION
AUTOMATIC TRANSMISSION WIRING CONNECTION
MANUAL TRANSMISSION WIRING CONNECTION
PROGRAMMING PROCEDURE
- Press and hold the programming button:
- Connect the 4-PIN Data-link harness (Black connector).
- The Blue, Red, Yellow and Blue & Red LEDs will alternatively illuminate.
- Release the programming button when the LED is BLUE.
- If the LED is not solid BLUE disconnect the 4-Pin connector (Data-Link) and go back to step 1.
- Insert the required remaining connectors.
- Turn the key to the Ignition ON/RUN position.
- The BLUE LED will flash rapidly.
- Turn the key to the OFF position.
- The BLUE LED will turn off.
The module is now programmed.
REMOTE STARTER FUNCTIONALITY
WARNING
The information on this sheet is provided on an (as is) basis with no
representation or warranty of accuracy whatsoever. It is the sole
responsibility of the installer to check and verify any circuit before
connecting to it. Only a computer safe logic probe or digital multimeter
should be used. FORTIN ELECTRONIC SYSTEMS assumes absolutely no liability or
responsibility whatsoever pertaining to the accuracy or currency of the
information supplied. The installation in every case is the sole
responsibility of the installer performing the work and FORTIN ELECTRONIC
SYSTEMS assumes no liability or responsibility whatsoever resulting from any
type of installation, whether performed properly, improperly or any other way.
Neither the manufacturer or distributor of this module is responsible of
damages of any kind indirectly or directly caused by this module, except for
the replacement of this module in case of manufacturing defects. This module
must be installed by qualifi ed technician. The information supplied is a
guide only. This instruction guide may change without notice. Visit
www.fortinbypass.com to get the latest version.
Notice: Updated Firmware and Installation Guides
Updated fi rmware and installation guides are posted on our web site on a
regular basis. We recommend that you update this module to the latest fi
rmware and download the latest installation guide(s) prior to the installation
of this product.
Module label
Copyright © 2006-2018, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED PATENT PENDING
TECH SUPPORT
1-877-336-7797
ADDENDUM GUIDE
www.fortinbypass.com
WEB UPDATE
FAQ
Q: Is the installation of the hood pin mandatory?
A: Yes, the hood pin is a mandatory safety element for proper
functionality of the system.
Q: Can I install the product myself?
A: It is recommended to have the product installed by a qualified
technician to prevent any damage to the vehicle.
Q: How do I update the firmware version?
A: Use the Flash Link Updater or Flash Link Mobile tool (sold separately)
to add the firmware version and options.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>