NEO Steam Faze 1000 Professional Fog Machine User Manual
- July 13, 2024
- NEO
Table of Contents
NEO Steam Faze 1000 Professional Fog Machine
Specifications
- Model: STEAM FAZE 1000
- Type: Professional Fog Machine
- Heater Wattage: 1500 watts
- Control Options: LCD screen, DMX control
Product Usage Instructions
Continuous Smoke Operation
To start continuous smoking:
- Press the Start/Pause button.
- To stop smoking, press the Start/Pause button again.
The icon displays the volume of output and fan speed during continuous smoking. You can still press the Menu button to set the built-in function parameters.
Timing Smoke Operation
When the machine is READY:
- Press the Up/On button to start timing smoking.
- Press the Down/Off button to stop timing smoking.
Pressing the Start/Pause button during timing smoking can activate continuous smoking. Press the Start/Pause button again to stop continuous smoking and return to the timing smoking state.
DMX Operation
The DMX control takes priority over remotes and built-in control.
- Valid DMX signal controls the machine through the DMX controller.
- You can adjust DMX Address by pressing Up and Down buttons.
FAQ
- What does it mean when fault warnings flash on the machine?
If you see “OVERHEAT !!!” it indicates that the heater temperature is too high or the temperature sensing wire is disconnected. “NO HEATING” means the machine cannot heat up.
PEASE READ THE INSTRUCTIONS CAREFULLY BEFORE USE
OVERVIEW
STEAM FAZE 1000
PROFESSIONAL FOG MACHINE
THE STEAM FAZE 1000 is a compact fog machine with a robust and modern design.
It has a 1500 watt heater that allows it to start generating fog within three
minutes of turning it on. To facilitate manual control, it has an LCD screen.
It can also be controlled by DMX.
Specifications
Effects
- Fog Output: 17500 (ft3/min)
- Output Adjustment: 5 – 100%
- Fan Speed Adjustment: 5 – 100%
- Smoke guide angle: -15~60 degrees
- Fluid Consumption Rate: 7ml/min.
Control
- DMX Channels: 2CH
- DMX Modes: 1
- DMX Connectors: 3 & 5 PIN XLR
- Primary/Secondary: NO
- On Board Control: Continuous fogging/Timing fogging
- Stand Alone: YES
- Display: LCD
- First Warm Up Time: 60s
- Max Continuous Output Duration: Continuous
- NoFluid Warning: YES
- Other Warnings: Overheat & No heating Warning
- Operate with exterior controller: YES
- Remote controller connectors: 1/4” JACK
- Manual fogging: YES
- Self-clean Function: YES
Power
- Input/Variable/Switchable: 230V or 240V
- Hz: 50 or 60Hz
- Heater Power: 1000W
- Consumption: 1040W
- Fuse or No Fuse breaker: NFB10A (230V)
- Cable / Plug Type: HO3VV – F3G,0.75m2 + powerCON
- Approvals: ETL,CE, FDA, etc.
Fixture
- IP Rating: N/A
- Cooling: fan, air, cool, etc.
- Max Ambient Temperature (Ta): 40°C
- Surface Temperature of body (Tc): 60°C
- Hanging Bracket: YES
- Handle: NO
- Tank: 4L
- LED under Tank: NO
Dimensions
- Size (LxWxH): 358x310x382mm
- Weight: 7.8kg
Accessories (Included)
- Controller: NO
- Long press Up/Down button to change the value continuously and fast.
- Set values are automatically saved.
CONTINUOUS SMOKE OPERATION:
Press the “Start/Pause” button to start continuous smoking, and then press the
“Start/Pause” button again to stop smoking.
Icon displays the volume of output and fan speed during continuous smoking. At this time, can still press the Menu button to set the built-in function parameters.
TIMING SMOKE OPERATION
When the machine is “READY”, press the “Up/On” button to start timing smoking.
The picture on the right shows the timing smoking start, with the D and I numbers jumping in turn, displaying the duration/interval countdown. Press the “Down / Off” button to stop timing smoking.
Pressing the “Start/Pause” button during timing smoking can also activate continuous smoking, the icon content is displayed. Press the “Start/Pause” button again to stop continuous smoking and return to the timing smoking state.
DMX OPERATION:
The DMX control takes priority over the remotes and built-in control. When the machine receives a valid DMX signal, it is controlled by the DMX controller and ignores the remotes and built-in control, the icon screen is displayed. V represents the smoke volume controlled by DMX. F represents the fan speed controlled by the DMXs In this state, you can still press the Up and Down to adjust the DMX Address.
DMX CHART:
| CH1 | CH2 |
|---|---|
| DMX Value | Smoke volume |
Speed
5-255| 5~100| 0-255| 5~100
0-4| OFF| |
In the DMX state, the “Start/Pause” button serves as a manual smoking switch and pressing and holding this button sprays smoke at the maximum output; After releasing the “Start/Pause” button, stop manual smoking and return to the control state of the DMX.
FAULT WARNING
Flashing to display the following warning icons.
Indicates that the heater temperature is too high, or the temperature sensing wire disconnected.
Indicates that the machine cannot heat up.
Indicates that the fog liquid is used up or cannot be extracted.
Add fog liquid to the tank and press the “Start/Pause” button to reset.
PRECAUTIONS
After the smoking stops, the fan will still maintain for 5 seconds, and then
switch to standby. “CLEAN” flashes to indicate that the remaining smoke is
being cleared. After “CLEAN” disappears, the power can be cut off.
If want to shut down the machine after use, please first stop all smoke
actions, wait for the “CLEAN” character to stop flashing and disappears, and
then cut off the power.
Cut off the power supply after the residual liquid in the heater has been
gasified, to extend the service life of the machine and avoid the phenomenon
of short-term smoke spraying after the next startup.
NEVER suddenly cut off the power supply while the machine is spraying smoke
normally.
neo.amproweb.com
Facebook/amprogroup
Youtube/amprogroup
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>