neo Smart Bridge Pro User Manual
- June 3, 2024
- NEO
Table of Contents
Intelligent friendly light
lmmax NEO SMART BRIDGE PRO
user manual
Product Description
It is a mini Smart Gateway .It consists of a highly integrated Wi-Fi module,
low power-consuming ZigBee module, and PCBA.
It can be connected to the Smartlife Smart app for device adding, reset,
third-party control, and ZigBee group control, meeting smart home
requirements.
Technical specifications
Features supporting security logic: Yes
Color: white
Protocol: ZigBee 3.0, Wi-Fi, ; BLE5.0
Frequency: 2400MHz~2483.5MHz
Maximum RF output power: WiFi/BLE: 11dBm
ZigBee: 10dBm – max 11dBm
Source input voltage: AC 230V 50-60Hz
Smart gate input voltage: 5V 1A
Working voltage: 1.8 – 3.3V
Dimensions: 15 x 60 x 60 mm
Weight: 33g
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation
Attention that changes or modification not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment
Note: This product has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This product generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this product does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver. -
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
-
Consult the dealer or an experienced radio/TV technician for help
This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body
Application installation and commissioning
Step1: Download&Registration
Scan the QC Code to download” Smart Life”APR Or Search”Smart Vein Apple store
or Google Play to install the APR. Open the” Smart Life”APP, tap”Register”to
get an account with your phone number or E-mail. Sign in the APR.
Step2: Add Decices in Easy Mode ( Recommend ) Make sure your product is
powered on Make sure your mobile phone is connected to your Wi-Fi Press the
power button until the indicator begin to flash quickly (about
2timers/secon-d),this means the device is already for configuration Open your”
Smart Life”APP, tap”+”on the top right of the APP Select Device Type, tap”
confirm indicator rapidly blink’: It will fetch the password of the Wi-Fi
network your mobile phone connected. Tap”Confirm”to connect to the device,
when it appears” successfully add ldevice”, then the connection is completed
and your devices is listed in your APP list.
Add Devices in AP Mode (If failed in Easy Mode,user could use AP mode)
Press the power button for more that 5seconds until the indicator begin to
flash quickly, then press it for another 5seconds until the indicator flash
slowly. Tap”+” on the top right of the APP,Select DeviceType Tap” AP Mode “on
the top right7confirm indicator slowly blink’: It will fetch the password of
the Wi-Fi network your mobile phone connected. Tap”Confirm”and “connect now”to
go to the WLAN setting interface in your mobile phone. Select the Wi-Fi
network named ” Smart Life_xxx”to connect it. Return to the” Smart Life”APP,
the connection will start automatically When it appears” successfully add
ldevice”, then the connection is completed and your devices is listed in your
APP list.
How to reset the device (put it into pairing mode)?
- Press the reset button for 5 seconds until the LED indicator flashes quickly.The device is switched to basic pairing mode.
- Press the reset button again for 5 seconds until the LED indicator flashes slowly.The device switches to AP mode.
Safety Information
CAUTION: Keep out of reach of children. This product contains small
parts, which may cause suffocation or injury if swallowed.
WARNING: Every battery has the potential to leak harmful chemicals that
can damage skin, clothing or area where the battery is stored. To avoid the
risk of injury, do not allow any substance from the battery to come into
contact with the eyes or skin. Every battery may burst or even explode if
exposed to fire or other forms of excessive heat. Take care when handling the
batteries. To reduce the risk of injury from mishandling the batteries, take
the following precautions:
- Do not use different brands and types of batteries in the same device
- When replacing the batteries, always replace all the batteries in the device
- Do not use rechargeable or reusable batteries.
- Do not allow children to insert batteries without supervision.
- Follow the battery manufacturer’s instructions for proper battery handling and disposal.
CAUTION: The product and batteries should be disposed of at a recycling
centre. Do not dispose of them with normal household waste. ”
CAUTION: To ensure safe use of the product, wires must be brought at the
installation site according to valid regulations. The installation must only
be carried out by an individual with the appropriate certification in the
field of electronics. During installation or when a fault is detected, the
power cable must always be disconnected from the socket (in the case of direct
connection, the relevant circuit breaker must be switched off). Improper
installation can damage the product and cause injury.
CAUTION: Do not disassemble the product, electric shock may occur.
CAUTION: Use only the original power adapter provided with the product.
Do not operate the device if the power cord shows signs of damage.
CAUTION: Follow the instructions in the enclosed manual.
Maintenance Protect the device from contamination and soiling. Wipe the device
with a soft cloth, do not use rough or coarse materials.
DO NOT USE solvents or other aggressive cleaners or chemicals.
LED status
Red LED (WiFi)
On – the device is connected to a WiFi network
Flashing – device is connecting to WiFi network
Not lit – WiFi network information is congured but cannot connect
Blue LED (Zigbee/Bluetooth)
Flashing – devices can connect to the smart gateway
On – Zigbee/Bluetooth connection is active
Not lit – Zigbee/Bluetooth connection is not active
https://smartapp.tuya.com/immaxneosmart
Výrobce a dovozce: IMMAX, Pohoří 703, 742 85 Vřesina, EU
www.immax.cz
Vyrobeno v P.R.C.
References
- Velkoobchod s LED technikou IMMAX | Immax.cz
- Velkoobchod s LED technikou IMMAX | Immax.cz
- Velkoobchod s LED technikou IMMAX | Immax.cz
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>