SCOPREGA GE8S0006 Electric Pump Instruction Manual

: July 12, 2024
: SCOPREGA

Table of Contents

SCOPREGA GE8S0006 Electric Pump
Product Information
Product Usage Instructions
INTRODUCTION
F UNCTIONAL DESCRIPTION
TECHNICAL DATA
INSTALLATION
USAGE AND F UNCTIONS
TYPES OF USE
TROUBLESHOOTING
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

SCOPREGA GE8S0006 Electric Pump

Product Information

Specifications

Maximum Pressure: 1000 mbar
Maximum Flow Rate: 2000 l/m
Voltage: 120 Vac 60 Hz | 230 Vac 50 Hz
Maximum Current: 10 A (120 V) | 20 A (230 V)
Weight: ~10 Kg
Function: Inflate / Deflate

Product Usage Instructions

Installation

Connect the power cable to a power outlet.
Attach the inflation tube with pressure control to the pump.

Usage and Functions

Setting the Pressure: Adjust the pressure using the pressure selection display.
Display: Monitor the pressure settings on the display.
On/Off Button + Functions: Use the button to control the pump.
Automatic Stop System (A.R.S) Management: The pump will stop automatically when the preset pressure is reached.

A.R.S System Management
The internal pressure control system with automatic refill is managed directly by the inflation tube without the need for additional external accessories.

Airflow Management
After setting the pressure, the pump autonomously manages the airflow during inflation into the inflatable object.

Temperature Control
If the pump overheats, do not disconnect it from the power source. After the overheat alarm, the pump will not restart automatically. The internal temperature will decrease automatically due to the built-in fans.

Frequently Asked Questions (FAQ)

Q: What are the recommended uses for Hyperpump C?
- A: Hyperpump C is ideal for inflating tents, inflatable structures, inflatable barriers, SUP, and various types of inflatables. Ensure you follow the safety parameters indicated on the pump and packaging.

HYPERP UMP C

ELECTRIC P UMP

HYPERP UMP C 120 V: GE8S0006
HYPERP UMP C 230 V: GE8S0004

Read these instructions before using the inflator.
Failure to follow all of the instructions listed below may result in damage to the product and/or cause serious injury to persons.

INTRODUCTION

HYPERP UMP C

The Hyperpump C is the most versatile inflator ever made, capable of autonomously adapting to the specifications of the inflatable by adjusting the airf low according to the target pressure set via the display.
Its high performance allows you to inflate any type of inflatable, especially SUPs in less than a minute!
Thanks to the A .R .S. system, the inflator controls the pressure directly through the inflation tube, without the need for external sensors.
The Hyperpump C’s degree of protection is IP54.

F UNCTIONAL DESCRIPTION

PRELIMINARY WARNINGS

Follow all instructions in this document.
Keep these instructions.
Do not obstruct the air vents.
Always protect the power cord.
Do not open the inflator. Have all maintenance activities performed maintenance to qualified maintenance technicians authorized by Scoprega. Maintenance is required when the unit is found to be in any way damaged or inoperative.
Do not tamper with the product. Opening the inflator will result in the voiding of the warranty.
Provide adequate ventilation.
Avoid placing objects in the vicinity of the product during its operation.
Keep this product out of the reach of children.
The inflator in motion produces vibration so to avoid accidental falls, we recommend using it on the floor.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to prevent them from playing with the appliance.

TECHNICAL DATA

MAX PRESSURE: 1000 mbar
MAX AIR FLOW : 2000 l/m
CHARGE VOLTAGE: 120 Vac 60 Hz | 230 Vac 50 Hz
MAX CURRENT: 10 A (120 V) | 20 A (230 V)
WEIGHT : ~ 10 Kg
FUNCTION : Gonfia / Sgonfia

RECOMMENDED USES

The HYPERPUMP C is the ideal inflator for tents, inflatable structures and inflatable barriers.
comply with the protection parameters indicated on the box and pump.

INSTALLATION

USAGE AND F UNCTIONS

TO USE
Connect one end of the hose to the inflation port (Point 5, Fig. 2), and the other end to the valve of the inflator.
Once the connections have been made, connect the inflator to the power supply and press the ON/OFF button (Point 1, Fig 1).

N.B. Check that the inflator hose is always connected to the inflator and the structure during inflation.
N.B. If the power cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

TYPES OF USE

Depending on the inflation requirements, the use of hoses varies.
Depending on the maximum attainable pressure of the inflatable (up to a maximum of 1000 mbar), the correct inflation hose must be used to avoid damage to the inflator and the supplied hoses.

N.B. The Ø40 mm hose supplied must be used for inflatables that do NOT need to be inflated to a pressure greater than 600 mBar.
N.B. To inflate at pressures above 600 mBar up to 1000 mBar use the high pressure hose supplied.
N.B. In the event of damage to the inflator or hose, they must be replaced or repaired by the manufacturer, its ser vice agent or similarly qualified persons in order to avoid a hazard.

TO INFL ATE
When the green light on the ON/OFF button (Point 1, Fig 1) lights up, the display will show the pressure that the inflatable has to reach. Now press the AUTO CYCLE button (leds light up) and after two seconds the Hyperpump C will start to inflate.

CHANGE THE OPERATING PRESSURE
Press the MODE button (Point 3, Fig 3) to select the unit (mbar/psi/kPa/bar), then use the SET-/SET+ buttons (Point 1, Fig 3) to change the pressure value on the display.
After 2 seconds the display stops flashing and the pressure is stored. The pressure can be changed between 0 and 1000 mbar.

N.B. When the preset pressure is reached, the inflator stops automatically.
N.B. Ensure that the pressure is set correctly according to the specifications on the inflatable.

A .R.S. SYSTEM MANAGEMENT

The pressure control system inside the inflatable with automatic refilling is carried out directly from the inflation hose, without the addition of external accessories.

CHANGING THE FILLING PRESSURE

By pressing the MIN button (Point 4, Fig 3) the display will start f lashing and the filling pressure can be changed using the SET-/SET+ buttons (Point 1, Fig 3). After two seconds the display stops f lashing and the tolerance pressure is stored. It is possible to adjust the filling pressure up to 30 mbar in relation to the operating pressure.

TO CHANGE THE DISCHARGE PRESSURE
Press the MAX button for 3 seconds, the display will start f lashing. Use the SET-/SET+ buttons to change the value. After two seconds the display stops f lashing and the value is stored.

There is the possibility to adjust the discharge pressure from 30 to 70 mbar in relation to the operating pressure.

After changes press AUTO CYCLE. The two LEDs light up after two seconds and the red LED goes out ; the green LED indicates that the inflator will start to inflate/discharge and recharge automatically.

With the automatic cycle activated (A .R .S. – LEDs lit), the unit will automatically check the pressure of the inflatable structure.
N.B. In the event of a power failure during operation, the inflator will keep the working settings memorised. It will restart automatically as soon as the power supply is restored.

AIR FLOW MANAGEMENT:
Once the connections have been made and the pressure set (Page 14), during the inflation phase the inflator autonomously manages the f low of air to be emitted inside the inflatable.

N.B. Use the Ø40 mm hose for inflatables that do NOT need to be inflated to a pressure higher than 600 mbar, and the high-pressure hose for pressures up to 1000 mbar.
The Hyperpump C behaves in accordance with the target pressure that you set in total autonomy.
Therefore by managing the pressure set via the display (Point 3, Fig. 1), the inflator will manage the air f low.

N.B. The air flow will increase as the millibar to be reached increases.
This feature, unique in the electric inflator market , allows for the best efficiency during the inflating phase.

OVERHEATING ALARM
In the event of prolonged use, the motors may overheat , and the inflator will go into lockout phase.
In this case, an alarm code will appear on the display
– A01 = Overtemperature

N.B. In case of overheating, DO NOT disconnect the inflator from the power supply.
N.B. After the over-temperature alarm the inflator will NOT restart automatically.

The internal temperature of the inflator will lower itself thanks to the built-in fans.
N.B. Provide proper ventilation of the inflator during the cooling phase.

After the temperature has dropped, and the alarm code is no longer displayed, press the AUTO CYCLE button on the display (Point 6, Fig.3 ) to restart the inflator.

GENERAL SAFATEY RULES

HOSE INSTALLATION
When installing a hose, it is important to follow certain rules.
This is to achieve the best performance and avoid damage that could compromise the life of the hose.

N.B. The minimum bending radius is 40 mm / 1.57 inch.
Installations below the minimum bend radius or excessive bending in the area of the fittings may break the hose.

N.B. Assemble the hose so as to withstand length variations due to working pressure, pump movements and related tolerances. Avoid live assemblies.

N.B. Avoid abrasions, bumps and cuts along the entire length of the hose during installation and use.

N.B. The life of a hose in twisting is greatly reduced.
To avoid twisting during installation and use, check that the spiral always follows a linear course.

N.B. The length of the hose should be such as to accommodate the motion and should not go below the minimum bending radius.
The hose allows relative movements between two connected sources. Avoid abrasion, tension and twisting during installation and use.