Xplova NOZA ONE Smart Trainer User Guide

Xplova NOZA ONE Smart Trainer

KNOWING YOUR NOZA ONE

Package Contents

• Xplova NOZA ONE bike trainer main unit
  

• Front bottom tube (Bolt and nut are Included within it)

• Rear bottom tube
  

• Rear bottom tube bolt x2
  

• Rear bottom tube nut x2

• Front bottom wrench

• Flywheel/cassette cover bolt wrench (2mm Hexagon

• Flywheel/cassette washer

• Decorative bolt cover x2

• Rear bottom wrench

• Flywheel/cassette cover
  

• Flywheel/cassette cover bolt x2

• Quick release kit

• Adapter for quick release

• Control module

• Control module screw x2

Notice: Accessories may vary by country or region.

Product Appearance

ASSEMBLY INSTRUCTIONS

Assembly Instructions Notice

Front bottom tube installation

Install according to the direction shown in the figure, press the spring button during installation, and rotate the front bottom tube slightly to make the spring buckle go through any hole in the front bottom tube. Then tighten the bolts and the front bottom tube can be installed.

• Note: 1. The part marked in red is a plastic pipe sleeve, which is installed to prevent the metal pipes from rotating each other, please do not discard it.
  

• Note: 2. The height of the trainer can be adjusted through the spring button and the installation of the two holes on the front bottom tube to adapt to different training models. The adaptation category is shown in the figure.

Flywheel/cassette cover installation

After taking out the filler from the flywheel/cassette cover, first tighten the flywheel/ cassette cover onto the flywheel, and then lock the two screws, as shown in the figure.

• Note: 1. The flywheel cover plays a role in protecting the machine, personnel safety and aesthetics purpose, please be sure to install it in place!
  

• Note: 2. For detailed installation methods, please refer to the specific chapters.
  

Assembling the Xplova NOZA ONE

1. Open the packing box, remove the styrofoam top cover and take out the installation tools and accessories from the accessory bag.

   • For front bottom tube installation use:
   • Front bottom wrench
   • For the installation of the rear bottom tube:
   • Rear bottom tube bolt x2
   • Rear bottom tube nut x2
   • Decorative bolt cover x2
   • Rear bottom wrench
   • For the installation of Flywheel/ cassette cover:
   • Flywheel/cassette cover
   • Flywheel/cassette cover bolt x2
   • Flywheel/cassette cover bolt wrench
   • For the installation of control module:
   • Control module
   • Control module screw x2

2. Take out the NOZA ONE bike trainer main unit and front bottom tube from the styrofoam cover and install according to the illustrations.
   
   
   Diagram of completed front bottom tube installation
   TIP: Press down the spring button when installing. When installation is done, make sure the button goes through the locating hole on the front leg.

3. Put the front leg on the ground as a support to lift the trainer, put rear bottom tube bolt through the holes on the rear bottom tube and secure it tightly to the trainer main unit. Then use the rear bottom wrench to screw the rear bottom tube nut tight, and then install the decorative bolt cover.
   

4. Tighten the bolts in the direction according to illustration, screw tight the front bottom tube. (Bolt and nut are included in the front bottom tube)
   

5. After removing the filler from the flywheel/cassette cover, place the flywheel/ cassette cover in the direction shown in the figure below and tighten it, use the flywheel/cassette cover wrench to tighten the two flywheel/cassette cover bolts.

6. Install the battery according to the following diagram:
   

7. Take out the control module from the accessory bag and put in two AAA batteries.

8. Put the control module into the main beam according to the direction shown in the figure.

9. Use a screwdriver to tighten the control module screws to complete the battery installation.
   Attention :
   Discarded dry batteries should be disposed in time, please do not try to disassemble them. Please remove the battery if the battery is not used for a long period of time to avoid damage to the equipment due to battery leakage.

10. Install the flywheel/cassette (sold separately) into the cassette body manually and use the cassette nut to secure it on the cassette body, and lock the cassette to prevent it from loosening.
    
    Attention:
    The cassette body of NOZA ONE bike trainer is compatible with Shimano and SRAM cassette, an 11-speed cassette can be installed directly. If you use a non-11-speed cassette, please install the cassette washer into the bottom of the cassette body before installing the cassette.

Mounting your bicycle

Shift the chain on your bicycle to the smallest sprocket of the cassette and then remove the rear wheel. Align the bicycle chain with the smallest sprocket of the cassette of NOZA ONE, and then put on the chain as well as mount the bicycle on NOZA ONE’s axle to have the bicycle in a suitable position for riding.
Please use the bicycle quick release kit properly with care. When the arc of the rotating arm of the quick release kit is toward outside, it means the kit is in a released state. Rotate the rotating arm of the kit clockwise to tighten the quick release kit. The rotating arm of the quick release kit should be placed on the other side of the NOZA ONE’s cassette body.

Please refer to the following illustration for the installation of the thru axle bicycle. Insert the thru axle from the other side of the cassette and tighten the axle.

Attention:

1. Please firmly tighten the quick release lever and the thru axle to prevent damage to property or human body. If you cannot tighten the quick release lever and the thru axle, please contact your dealer or Xplova customer service. Please DO NOT attempt to use the NOZA ONE under this situation.
2. When mounting the bicycle, please lift its front wheel and press the frame down to make the bicycle firmly mounted on the NOZA ONE.

Indicator descriptions

| Categories| Type of indicator light
---|---|---
Battery exhausted| System LED indicator light off.
Bike trainer at sleep mode
Low power consumption mode
Wording status| Not Connected — Communication indicator light flashing slowly.
Connected — Communication indicator light always on
Low battery| System indicator light flashes in every 10 seconds.
Spindown| Alternate flashing of red light and blue light. Blue light will always on after spin down completed.

NOZA ONE has two indicator lights, one indicates system status, the other indicates communication status. See illustration for locations of the two indicator lights:

Cycling game QSG

1. You may download some of the cycling game training softwares on PC/MAC or smartphone. Here are a few key games:

   • ZWIFT: www.zwift.com
   • Rouvy: rouvy.com
   • Onelap: www.onelap.cn
     

2. Install games and setup connection to NOZA ONE. NOZA ONE will only display power and speed data.

3. Once you mount the bike, you are ready to start the game training experience.
   

Training program and uploading riding data

Use the Xplova Workout Plus App to control NOZA ONE and use multiple training programs.
If you want to conduct more detailed analysis, you can use Xplova Workout Plus App to upload your data to website for analysis.

More of the amazing functions

If you want to experience the full functions of the NOZA ONE, we recommend that you install the Xplova Workout Plus App on your smartphone. Xplova Workout Plus App enables you to:

• View/store training records
• Upload the records to different platforms (such as Xplova, Strava, Training Peak and so on)

Please go to Google Play or App Store to search for ”Xplova Workout Plus” to download and install the app. If you want to get a better understanding of the product, please go to our official website at www.xplova.com and download the User Manual.

Specifications

& SRAM 8/9/10/11 speed cassette
Connectivity| ANT+, Bluetooth Smart
Firmware Upgradable| Yes
Box Dimensions| 700 x 485 x 270 mm

SAFETY PRECAUTIONS AND REGULATIONS

Safety precautions before use

1. When the bike trainer is active, please do not touch it and you should keep non users, animals or objects away from it to avoid danger.
2. Consult your coach before you start any training plans.
3. Please DO NOT put your hands or any object near the spinning parts of the Xplova NOZA ONE.
4. The flywheel/cassette of the Xplova NOZA ONE might gets hot after you use it for a while. Please DO NOT touch the flywheel/cassette within a short time.
5. Please DO NOT attempt to disassemble the bicycle when the cassette is running.
6. When you are using the Xplova NOZA ONE, keep your children and pets away from it to prevent injury.
7. Xplova NOZA ONE can only be installed and used on a firm, level ground.
8. When training is in progress, please ride safely.
9. Keep away from water.
10. Before training, you should check if the bicycle is firmly secured to the Xplova NOZA ONE.
11. Xplova NOZA ONE can only be used after it is completely assembled.
12. When using the Xplova NOZA ONE, you can only use accessories certified by Xplova.

Notices

1. Xplova shall not be held responsible for users using software, applications and devices from other companies that result in malfunctioning of the Xplova NOZA ONE.
2. As ANT+™ and Bluetooth are mutually exclusive, it is impossible for the Xplova NOZA ONE to send data simultaneously through ANT+™ or Bluetooth, i.e., When one of the protocols is in use, the Xplova NOZA ONE will automatically stop the other protocol to avoid the possibility of causing NOZA ONE programs to misbehave.
3. Radio devices may cause interference and may change or completely prevent the Xplova NOZA ONE from functioning normally. Therefore, when training using the NOZA ONE, it is advised to stay away from high voltage power lines, traffic signals, railway power lines, buses or trains.
4. When the Xplova NOZA ONE is not in use, make sure not to expose it to direct sunlight for long periods of time.

Disclaimer

Attention! Xplova shall not be held responsible for temporary or permanent injury to the user out of using the Xplova NOZA ONE (either directly or indirectly).

Maintenance and care

1. When cleaning the bike trainer, please use neutral lubrication oil. DO NOT use corrosive detergents.
2. DO NOT burnish the surface of the bike trainer or drill holes. Scratches or drilled holes will lead to occurrence of cracks.
3. Please place the bike trainer indoors and keep it dry to avoid damage from humidity.

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. (Section 15.21)

CAUTION:

Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the equipment.

Xplova Limited Product Warranty Policy

This Limited Product Warranty shall apply to Xplova products including all accessories as contained within the original Xplova gift box. Xplova warrants that products from its authorized distributors and retailers will meet the applicable product specifications and be free from all defects in material and workmanship during the Limited Product Warranty Period, one year starting from the date of original purchase, if the products are used and serviced in accordance with the user manual and other documentation provided to the purchaser at the time of purchase. This Limited Product Warranty is subjected to the following terms and conditions:

1. To obtain warranty service, a proof of purchase, an original or copy of the sales receipt from the original retailer, is required.

2. This Limited Product Warranty is only valid and enforceable in the country/region where the product is sold.

3. This Limited Product Warranty is at sole option of Xplova to either repair or replace the defective product during the Limited Product Warranty Period. Xplova will not replace missing components from any package purchased through on-line auctions.

4. To obtain warranty service, contact your local Xplova authorized retailer or Xplova for shipping instructions and an RMA number.

5. This Limited Product Warranty covers expenses for inspecting and repairing the product during the Limited Product Warranty Period. The defective product shall be delivered by the purchaser at his/her own expense to the designated premises together with the proof of purchase and RMA number.

6. Xplova will return the repaired or replaced product to the drop-zone for collection by the customer in good working condition. All replaced faulty products or components will become the property of Xplova. If Xplova repairs or replaces the product, the repaired or replaced product shall continue to be warranted for the remaining time of the original warranty period or for three (3) months from the date of repair or replacement, whichever is longer.

7. Before returning any units for service, be sure to back up data and remove any confidential, proprietary, or personal information from the Product. Xplova is not responsible for damage to or loss of data.

8. Xplova reserves the right to add, delete or amend the terms and conditions at any time without prior notice on its website indicated below.

9. THIS LIMITED WARRANTY SHALL NOT APPLY IF THE DAMAGE WAS CAUSED BY ANY OF THE FOLLOWING:
   A. The product serial number has been removed, erased, defaced, altered or is illegible.
   B. The damage is resulting from the use of the product in a manner other than its normal and customary manner.
   C. Deterioration of the product due to normal wear and tear.
   D. The damage is arising from improper installation, unauthorized repair, alteration or modification to this product by third parties other than Xplova or its designee.
   E. The damage is arising from operating with components or accessories not officially authorized or provided by Xplova or used in other than its intended use.
   F. The damage is arising from exposure to abnormally corrosive conditions or operation with extreme heat or humidity.

10. XPLOVA WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL LOSSES OR DAMAGES TO ANY NATURE, INCLUDING BUT NOT LIMITED TO LOST PROFITS OR COMMERCIAL LOSS, TO THE FULLEST EXTENT THAT THOSE LOSSES OR DAMAGES CAN BE DISCLAIMED BY LAW.

11. This Limited Product Warranty does not affect the customer’s statutory rights in law specific to the country of purchase, such rights remain protected. Some countries do not allow the exclusion or limitation of incidental or consequential loss or damage, or limitation of the implied warranties, in those circumstances the preceding limitation of exclusions may not apply to such customers.

Warranty Coverage:

1. Under normal conditions of use, the product main unit and components gets a one year free after-sales maintenance services.
2. Please present the original purchase approval or receipt with this Product Warranty on upon of requesting a service. Service fee might be charged in accordance with this Product Warranty. Please note the Limited Product Warranty Period and service availability and response times may vary from country to country and may also be subject to registration requirement in the country of purchase. If you require assistance regarding warranty conditions, or any other enquiries, please contact the original retailer or Xplova.

Website: https://www.xplova.com

Product Warranty

Please retain the original purchase receipt or approval in order to protect your right of free warranty service.

Customer Support

Manufacturer : Acer Gadget Inc.
No.112, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City, Zip code: 221, Taiwan
Tel: +886-2-2790-3878
E-mail: service@xplova.com

Monday ~ Friday
9:00 – 18:00
+44 3717601019
xplovaServiceUK@Sertec360.com

Thank you again for purchasing the Xplova NOZA ONE. Xplova reserves the right to design, change specifications, and improve quality. Should you have any questions regarding use of the bike trainer, please visit our website at: www.xplova.com.

© 2021. All Rights Reserved.
Xplova NOZA ONE
This revision: 08/ 2021

References

• The world's most realistic indoor cycling app | ROUVY
• Contact Us | Bikesportz
• 顽鹿官网首页
• 顽鹿官网首页
• xplova
• xplova
• Zwift | The Indoor Cycling App for Smart Trainers & Bikes
• Zwift | The Indoor Cycling App for Smart Trainers & Bikes
• Contact Us | Bikesportz
• xplova

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>