Golfzon GZ-GWRS-22 Portable Golfsensor Radar User Guide
- June 13, 2024
- GOLFZON
Table of Contents
Golfzon GZ-GWRS-22 Portable Golfsensor Radar
Product Information
Component Roles and Functions
| Components | Roles and Features |
|---|---|
| Portable Golfsensor_RADAR | General strike sensing device (excluding putting |
balls) Connect
via Wi-Fi communication
Portable Golfsensor_IR| Putting Hitting Sensing Device Connect via Bluetooth
communication
ADAPTOR| Charger for Portable Golfsensor_RADAR
Product Using Instructions
Product connection configurations
- WAVE RADAR is connected to the control unit (PC or mobile device) via Wi-Fi.
- WAVE PUTT is connected to WAVE RADAR via Bluetooth. (However, the WAVE RADAR and the control unit must be connected.)
Product Image
- Charge Status LED
- Battery LED
- Wi-Fi LED
- BLE LED
- DC Jack
- Power Switch
- Camera (used for initial alignment and captures the golf swing motion)
Portable Golfsensor_RADAR (GZ-GWRS-22) Installation
- Place GZ-GWPS-22 outside the range of GZ-GWRS-22 as shown on the right. (Place GZ-GWPS-22 on a flat floor. Otherwise, it may affect direction.)
- Connect the power using the included Adaptor. (Recommend using 12V 3.33A)
- After connecting GZ-GWRS-22 in WAVE Skills, connect with GZ-GWPS-22.
- Open the WAVE Skills app and log in. (Guest mode available)
- Set Connect the device Additional device to use Wave putt.
- Connect GZ-GWPS-22.
- Enjoy practice and game at WAVE Skills.
Product Configuration and Specification
Product Contents
Specification
Category /Details
- Product Name: Portable Golfsensor_RADAR
- Hardware Version: Wave Radar V1.0
- Software Version: Wave-R1-2320201-146
- Size (Weight): 183x135x58mm (750g)
- Battery: Li-Ion 3,400mAh 7.2V
- Battery usage time: 4 hours of continuous use
- Battery charging time: 2 hours (12V, 3A)
- Input voltage: WAVE RADAR : DC 12V 3.33A
- Operating temperature: -10~50℃
- Communication: Wi-Fi 2.4G, BLE
Product Information
Component Roles and Functions
| Components | Roles and Features |
|---|---|
| Portable Golfsensor_RADAR | General strike sensing device (excluding putting |
balls) Connect via Wi-Fi communication
Portable Golfsensor_IR| Putting Hitting Sensing Device Connect via Bluetooth
communication
ADAPTOR| Charger for Portable Golfsensor_RADAR
Product connection configurations
WAVE RADAR
- WAVE RADAR is connected to the control unit (PC or mobile device) via Wi-Fi.
WAVE PUTT
- WAVE PUTT is connected to WAVE RADAR via Bluetooth.
- (However, the WAVE RADAR and the control unit must be connected.)
- Portable Golfsensor RADAR is a sensor that measures the movement of golf balls and clubs.
- Measures the user’s golf shot data using the Doppler effect.
- The golf shot results provide golf shot information through the connected device.
Product Installation
Product Image
- Charge Status LED
- Battery LED
- Wi-Fi LED
- BLE LED
- DC Jack
- Power Switch
- Charge Status LED: Indicates charging status.
- Battery LED: Indicates the remaining battery information.
- A. more than 50%: Green LED
- B. 50%~20%: Yellow LED
- C. less than 20%: Red LED
- D. less than 5%: Red LED Toggle
- Wi-Fi LED: Indicates the Wi-Fi device connection status.
- BLE LED: Indicates the BLE device connection status.
- DC Jack: Power adapter connector.
- Power Switch: Press the power switch for 3 seconds to turn the system ON.
- Camera: The camera is used for initial alignment and captures the golf swing motion.
Product Installation
Portable Golfsensor_RADAR (GZ-GWRS-22) Installation
- Place GZ-GWPS-22 outside the range of GZ-GWRS-22 as shown on the right. (Place GZ-GWPS-22 on a flat floor. Otherwise it may affect direction.)
- Connect the power using the included Adaptor.(Recommend to use 12V 3.33A)
- After connecting GZ-GWRS-22 in WAVE Skills, connect with GZ-GWPS-22. (GZ-GWPS-22 cannot be used alone.)
- Open the WAVE Skills app and log in. (Guest mode available)
- Set Connect the device → Additional device to use → Wave putt.
- Connect GZ-GWPS-22.
- Enjoy a practice and game at WAVE Skills.
FCC STATEMENT
FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>