TECNO CL6s Spark 20 Pro Plus Smartphone User Manual

July 11, 2024
TECNO

CL6s
User Manual

Exploded diagram specification

TECNO CL6s Spark 20 Pro Plus Smartphone -

1 OLED 2 LCM HEAT FILM
3 FRONT COVER 4 SIM CONNECTOR
5 50M FCAM BRACKET 6 70W BATTERY
7 MAIN BOARD 8 32M CAMERA
9 50M CAMERA 10 8W CAMERA
11 2M CAMERA 12 SIDE KEY FPC
13 COAXIAL CABLE 14 RECEIVER
15 LCM CON HEAT SINK 16 MIDDLE HOUSING B-COVER
17 8W CONDUCTIVE ADHESIVE 18 R MAIN CAM CON COP FOIL
19 2M CAMERA RUBBER 20 SCREW M1.4 L3.5
21 2M CAMERA TRIM 22 BATTERY COVER
23 SCREW M1.2 L1.7 24 CAMERA FILM
25 CAMERA TRIM 26 CAM GLASS TRIM
27 FORESIGHT COPPER FOIL 28 HEAT DISSIPATION

GRAPHITE SHEET

29| SCREW M1.2 L1.7| 30| SPK BOX
31| MAIN CONNECTOR

(ZIF/BTB)

| 32| SUB BOARD
33| FINGERPRINT| 34| MOTOR
35| AUDIO JACK RUBBER| 36| TYPE C USB RUBBER

Know your phone

TECNO CL6s Spark 20 Pro Plus Smartphone - phone

  1. Front camera
  2. Volume + button
  3.  Volume – button
  4. Power button
  5. NFC

SIM/SD card installation

  1. Power off your phone.
  2. Refer to the following picture for SIM/SD card installation.

TECNO CL6s Spark 20 Pro Plus Smartphone - SD card

Charging the phone

You can charge your phone with a charger or by connecting it to a computer using a USB cable (comes with the phone).
Use only TECNO chargers and cables. Other chargers or cables may damage the phone and invalidate its warranty.

TECNO CL6s Spark 20 Pro Plus Smartphone - Charging

FCC Caution

  1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
    (1) This device may not cause harmful interference.
    (2) This device must accept any interference received, including interference that may cause undesired operation.

  2. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information:
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of tissue. Device types:
CL6s (FCC ID: 2ADYY-CL6S) has also been tested against this SAR limit.
The highest SAR value reported under this standard during product certification for use at the ear is 1.117 W/kg and when properly worn on the body is 0.958 W/kg.
Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt-clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or an approved antenna.

Android is a trademark of Google LLC.
HiOS runs on Android™ OS.

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals