Forclover FLW-ER7236B Framed Dimmable Lighted Fog Free Bathroom Vanity Mirror Installation Guide

Forclover FLW-ER7236B Framed Dimmable Lighted Fog Free Bathroom Vanity

Mirror

IMPORTANT SAFETY INSTRUCTIONS

When using an electrical furnishing, basic precautions should always be followed, Requires two(2) persons in installation.

DANGER
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS MIRROR.

WARNING
To reduce the risk of burns, fire, electric shock or injury to persons. Use this furnishing only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer. Never drop or insert any object into any opening. Do not use outdoors.

WARNING
Risk of electric shock. Connect this furnishing to a properly grounded circuit only. See Grounding instructions.

GROUNDING INSTRUCTIONS

WARNING
This product must be connected to a grounded metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the product. An Electrical option cabinet must be wired to a 20 Amp GFI (Ground Fault Interrupter) protected circuit when used in bathrooms and all other locations required by the National Electric Code.

NOTE: To ensure the normal use of the product, it is required to set out wires as per the regulations of IEE. The product is only applicable to indoor installation. The installation must be executed by a professional electrician, wrong installation may lead to product damage and personal injury.

TOOLS REQUIRED FOR ASSEMBLY

PARTS INCLUDED

HARDWARE INCLUDED (not shown actual size)

NOTE: Determine overall mirror dimensions before proceeding to installation.

• All dimensions & specifications are approximate and subject to change without notice.
• Accessories and parts may vary from the picture above. Depends on the product model and size.

ELECTRIC CONNECTIONS

ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN

• WARNING: Shut off power before wiring the mirror.
• WARNING: An Electrical option mirror must be wired to a 20 Amp GFI (Ground Fault Interrupter) protected circuit when used in bathrooms and all other locations required by the National Electric Code.
• WARNING: This mirror must be connected to a grounded, metal permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the mirror.
• CAUTION: Requires 120 VAC 20 Amp GFI protected circuit.

vertical hanging

horizontal hanging

Electric wiring : Be sure to provide enough wire to make the proper and safe connection to the Field/Power.

MIRROR FEATURES

• 5mm copper free silver mirror
• High quality LED Lighting
• CRI 90+, 3000-6000K CCT, IP44
• Color temperature and dimming
• Separate controlled defogger
• Vertical and horizontal mount options

INSTALLATION INSTRUCTIONS

PLACEMENT
Select the desired position of the mirror. Level and mark the location. (vertical and horizontal mounting opntions)

SUPPORT LOCATION
Measure the hanging bar holes and mark the drilling locations to ensure markings are leveled.

INSTALL SCREWS
Using a drill, make holes on a solid wall, and fill them with supplied plugs and screws into hanging bar holes tightly.

POWER OFF
Please turn off all the power before the mirror wires connect.

CONNECTION
Plug into the socket ,or cut off the plug then use the wire connector to connect the external power supply.(plug or hardwire connection options )

Warning: Strip wires to a suitable length.DO NOT connect the hardwire to a plug & socket outlet

Turn on the power
Hang up the mirror stable then turn on the power.

TOUCH SWITCH SETTING UP

How to use Touch Switch:

Left Touch Sensor

• Short touch to ON/OFF lighting.
• Light brightness is 10%-100% controlled by holding.
• Release the button when the light reaches the desired brightness.

Middle Touch Sensor

• Short touch to get the light temperature 6000K, 4000K and 3000K.
• Long touch to adjust the light temperature from 6000K-3000K.
• Release the button when the light reaches the desired color.

Right Touch Sensor

• Short touch to turn ON/OFF the defogger.

The mirror is equipped with a memory function to preserve the previous brightness/color settings.

Suggestion: The mirror is equipped with a memory function to preserve the previous brightness/color settings.

WARNINGS

1. Please do not use if you found the mirror has been broken.
2. Never put any sharp or heavy material on the mirror surface, otherwise, the glass mirror will be broken and body injury accidents may occur.
3. Turn off the power switch in storm lightning weather to avoid electric parts damage.

Use and Maintenance

CAUTION

USE

1. To avoid damage, do NOT knock the mirror with any hard objects;
   CLEANING

2. Do NOT clean the mirror with caustic cleaner. Do NOT wipe the mirror with a Bristle brush; MAINTENANCE

3. For daily maintenance, please use soft cloth and mild cleaner to clean the mirror.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>