Trust APIR-2150 Wireless Motion Sensor User Manual

June 9, 2024
Trust

Trust APIR-2150 Wireless Motion Sensor User Manual
Trust APIR-2150 Wireless Motion Sensor

  1. Open sensor housing
    Remove the screws to open the battery compartment.
    Assembly

  2. Install transmitter batteries
    Place 2x 1,5V AAA alkaline batteries in the battery compartments. The polarity should match the symbols on the holder.
    Assembly

  3. Assign code to a Trust Smart Home receiver
    Program the code of this transmitter into the memory of one or several Trust Smart Home receivers. Slide the LEARN switch from [DEL] to [SET] to send an ON-signal. Read the receiver’s manual for the code learning procedure.
    Assembly

  4. Code confirmation
    Slide the LEARN switch back to DEL and after a short pause slide the LEARN switch to SET again. The connected light or chime will react. If not, repeat the previous step.
    Assembly

  5. Set switch-off delay
    When no more motion is detected, the transmitter automatically sends an OFF signal after 5 secondsor 1/5/10 minutes.
    Assembly

  6. Set light sensitivity
    Slide the [R] switch to select 1 of the 3 light sensitivity levels. [H]: Sensor is always active. [M]: Sensor is active when the environment brightness is less than 20 lux (late afternoon). [L]: Sensor is active when the environment brightness is less than 10 lux (late evening). If you want to control a chime, always choose [H].
    Assembly

  7. Close sensor housing
    Tighten all screws to ensure waterproofness.
    Assembly

  8. Set horizontal detection range
    The horizontal detection range of the sensor is maximum 110° and minimum 20°. Remove, reposition or adjust the size of the plastic screens to adjust the angle.
    Assembly

  9. Mount the motion sensor
    Affix the holder at any desired location and place the motion sensor into the holder.
    Assembly

  10. Set detection direction
    Loosen the clamp screw and point the motion sensor to your desired position. When satisfied tighten the clamp screw. The sensor needs 30 seconds to analyze its environment, beforeit becomes operational.
    Assembly

  11. Delete code from Trust Smart Home receiver memory
    Read the receiver’s manual for the single code delete procedure. Slide the LEARN switch from [SET] to [DEL] to send an OFF-signal.
    Assembly

Safety Instructions

Product support: www.trust.com/71091. Warranty conditions: www.trust.com/warranty To ensure safe handling of the device, follow the safety advice on: www.trust.com/safety
The Wireless range is strongly dependent on local conditions such as the presence of HR glass and reinforced concrete
Never use Trust Smart Home products for life-support systems. This product is water resistant. Do not attempt to repair this product. Wire colors may vary per country. Contact an electrician when in doubt about wiring. Never connect lights or equipment that exceed the maximum load of the receiver. Exercise caution when installing a receiver voltage may be present, even when a receiver is switched off. Maximum radio transmit power: -6.60 dBm. Radio transmission frequency range: 433,92 MH

Disposal of packaging materials – Dispose of packaging materials which are no longer needed in accordance with applicable local regulations.

Disposal of the device – The adjacent symbol of a crossed-out wheelie bin means that this device is subject to Directive 2012/19/EU.

Disposal of batteries – Used batteries may not be disposed of in household waste. Only dispose of batteries when they are fully discharged. Dispose of batteries according to local regulations.

Trust Electronics Ltd. declares that item number 71091/71091-02 is in with Directive Electromagnetic Compatibility Regulations 2016, Radio Equipment Regulations 2017. The full text ofthe declaration of conformity is available at the following internet address: www.trust.com/compliance

Trust International B.V. declares that item number 71091/71091-02 is in compliance with Directive 2014/53/EU – 2011/65/EU. The full text of the EU declaration of conformity is available at the following web address: www.trust. com/compliance

TECHNICAL SPECIFICATIONS

Code system Automatic
Number of Channels 1
Turn Off timer 5 sec or 1/5/10 min
Detection Range ± 6 m
Detection Angle Horizontal: 20-110°; Vertical: 65°
Power 2x AAA 1.5V alkaline battery (not included)
Size HxWxL:  83 x 90 x 99 mm

Declaration of Conformity

Trust International B.V. declares that this Trust Smart Home-product:

Model: APIR-2150 Wireless motion sensor
Item number: 71091/71091-02
Intended use: Outdoor

is in compliance with the essential requirements and other relevant provisions of the following directives:

ROHS 2 Directive (2011/65/EU)
RED Directive (2014/53/EU)

The full text of the EU declaration of conformity is available at the following  web address: www.trust.com/compliance

TRUST SMART HOME
LAAN VAN BARCELONA 600
3317DD DORDRECHT
NEDERLAND
www.trust.com

Trust Electronics Ltd.,
Sopwith Dr, Weybridge, KT13 0NT, UK.
All brand names are registered trademarks of their respective owners.
Specifications are subject to change without prior notice. Made in China

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals