FORCLOVER MRE-AL2028 Rectangular Frameless LED Light Anti-Fog Wall Mounted Bathroom Vanity Mirror Instruction Manual
- October 30, 2023
- FORCLOVER
Table of Contents
MRE-AL2028 Rectangular Frameless LED Light Anti-Fog Wall Mounted Bathroom
Vanity Mirror
Instruction Manual
IMPORTANT SAFETY INSTRUCTION
When using an electrical furnishing, basic precautions should always be followed, including the following:
DANGER | READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS MIRROR. |
---|---|
WARNING | To reduce the risk of burns, fire, electric shock or injury to |
persons. Use this furnishing only for its intended use as described in these
instructions. Do not use attachments not recommended by the manufacturer.
Never drop or insert any object into any opening. Do not use outdoors.
WARNING| Risk of electric shock. Connect this furnishing to a properly
grounded circuit only. See Grounding instructions.
GROUNDING INSTRUCTIONS:
This product must be connected to a grounded metal, permanent wiring system,
or an equipment-grounding conductor must be run with the circuit conductors
and connected to the equipment-grounding terminal or lead on the product.
WARNING
An Electrical option cabinet must be wired to a 20 Amp GFI (Ground Fault
Interrupter) protected circuit when used in bathrooms and all other locations
required by the National Electric Code.
NOTE: To ensure the normal use of product, it is required to set out
wires as per the regulations of IEE. The product is only applicate to the
indoor installation. The installation must be executed by a professional
electrician, wrong installation may lead to product damage and personal
injury.
PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
TOOLS REQUIRE FOR ASSEMBLY
Electrical Drill| 1/8″ Drill Bit| Pencil
Phillips Screwdriver| Tape Measure| Level
PARTS INCLUDED
NOTE: Determine overall mirror dimensions before proceeding to
installation.
*All dimensions & specifications are approximate and subject to change without notice
ELECTRIC CONNECTIONS
ALL WIRING SHOULD BE DONE BY A QUALIFIED LICENCED ELECTRICIAN
WARNING: shut off power before wiring the mirror.
WARNING: An Electrical option mirror must be wired to a 20 Amp GFI (Ground
Fault Interrupter) protected circuit when used in bathrooms and all other
locations required by the National Electric Code.
WARNING: This mirror must be connected to a grounded, metal permanent
wiring system or an equipment-grounding conductor must be run with the circuit
conductors and connected to the equipment grounding terminal or lead on the
mirror.
CAUTION: Requires 120 VAC 20 Amp GFI protected circuit.
Electric wiring: Be sure to provide enough wire to make the proper and safe connection to the Field/Power.
*Wire terminal plate is not included.
MIRROR FEATURES
- 5mm copper free silver mirror
- High output LED lighting: CRI 90+, 2700-6400K CCT, IP44
- Color Temperature changing touch switch for surface LED
- Vertical and horizontal mount options
- Defogger
INSTALLATION INSTRUCTIONS
-
PLACEMENT
Select the desired position of the mirror.
Level and mark the location.
(vertical and horizontal mounting options) -
SUPPORT LOCATION
Measure the hanging bar holes and mark the drilling locations ensure marking are leveled. -
INSTALL SCREWS
Using a drill, make holes on solid wall, and fill with supplied plugs and screws into hanging bar holes tightly. -
POWER OFF
Please turn off all the power before the mirror wires connection. -
CONNECTION
Plug into the socket, or cut off the plug then connect wires together and pushing the power supply wires into the junction box.
(plug or hardwire power connection options) Warning: when use plug connection, please mind the space gap between wall and mirror frame -
Turn on the power
Hang up the mirror stable then turn on the power.
FINAL ASSEMBLY
How to use Defogger Switch and Dimmer Switch:
| Left touch Senor
ON/OFF Anti-fog(The defogger power will automatically turn off after an hour)
Right Touch Sensor
ON/OFF Lighting
tap-tap color change, brightness control by holding
OPERATION
1.Touch the sensor button to turn ON the light. Tap-tap to change the light
temperature from 3000K, 4000K to 6000K.
2.Touch and hold the Light on sensor button to dim the light. Release the
button when the light reaches the desired brightness setting.
3.Touch the sensor button to turn OFF the light.
The mirrors are equipped with a memory feature to preserve the previous
brightness setting.
---|---
*Suggestion: Turn off the mirror power supply if you don’t use it for a
long time.
WARNINGS:
- Please do not use if you found the mirror have been broken.
- Never put any sharp or heavy material on the mirror surface, other wise the glass mirror will be broken and body injury accidents may occur.
- Turn off the power switch in storm lightning weather to avoid electric parts damage.
Use and Maintenance:
CAUTION:
Mirror and mirror’s body are constructed of mirrored glass and aluminum. Use a
damp cloth to clean your mirrors. Do not use any abrasive material as it may
damage the surface and finish of the mirror. A mild detergent may be used to
clean the surfaces of the mirror. Spray the cloth, not the mirrors or
surrounding surfaces.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>