Kenmore 580.76081700 Room Air Conditioner Owner’s Manual

Kenmore 580.76081700 Room Air Conditioner

Specifications

• Brand: Kenmore
• Model: 580.76081700
• Type: Window Air Conditioner
• Manufacturer: Sears, Roebuck, and Co.

Product Usage Instructions

• Safety Precautions:
  • It is important to follow these safety instructions to prevent harm or damage:
  • Avoid storing or using flammable vapors near the air conditioner.
  • Do not use extension cords or adapter plugs.
  • Ensure proper grounding of the air conditioner.
• Installation:
  • Follow these steps for installation:
  • If installing in a window, ensure both sides of the unit are supported and the window is slide-back type.
  • Consider removing the window screen before installation if needed.
• Maintenance:
  • To keep your air conditioner in good condition, perform these maintenance tasks:
  • Clean the air conditioner regularly.
  • Refer to the manual for instructions on removing the front grille.
• Troubleshooting:
  • If you encounter issues with your air conditioner, refer to the troubleshooting section of the manual for guidance.

FAQs

• Q: How long is the warranty for this air conditioner?
  • A: There is a one-year warranty on the room air conditioner and a five-year warranty on the sealed refrigeration system.
• Q: Can I use an extension cord with this air conditioner?
  • A: It is not recommended to use an extension cord with the air conditioner. Ensure the power cord is properly grounded.

WARRANTY

• FULL ONE-YEAR WARRANTY ON ROOM AIR CONDITIONER
  • For one year from the date of purchase, when this air conditioner is operated and maintained for normal room cooling according to the instructions in this owner’s manual, Sears will repair this air conditioner, free of charge, if defective in material or workmanship.
• FULL FIVE-YEAR WARRANTY ON SEALED REFRIGERATION SYSTEM
  • For five years from the date of purchase, when this air conditioner is operated and maintained for normal room cooling according to the instructions in this owner’s manual, Sears will repair the sealed refrigeration system (consisting of refrigerant. connecting tubing, and compressor), free of charge. if defective in material or workmanship.
• WARRANTY SERVICE IS AVAILABLE BY CONTACTING SEARS SERVICE AT 1-800-4-MY-HOME®
  • Warranty coverage applies only to air conditioners used for non-commercial, private household purposes.
  • This warranty applies only while this product is in use in the United States.
  • This warranty gives you specific legal rights, and you may also have another right which varies from state to state.
  • Distributed by Sears, Roebuck and Co., Hoffman Estates, IL 60179

SAFETY

IMPORTANT SAFETY INSTRUCTIONS

The safety instructions below will tell you how to use your room air conditioner to avoid harm to yourself or damage to your ROOM AIR CONDITIONER.

WARNING FOR YOUR SAFETY

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Read product labels for flammability and other warnings.

WARNING PREVENT ACCIDENTS

• To reduce the risk of fire, electrical shock, or injury to persons when using your air conditioner, follow basic precautions, including the following:
• Be sure the electrical service is adequate for the model you have chosen.
• If the air conditioner is to be installed in a window, you will probably want to clean both sides of the glass first. if the window is a triple-track type with a screen panel included, you may want to remove the screen completely before installation.
• Be sure the air conditioner has been securely and correctly installed according to the separate installation instructions provided with this manual. Save this manual and installation instructions for possible future use in removing or reinstalling this unit.
• Use gloves when handling the air conditioner. Be careful to avoid cuts from sharp metal fins on the front and rear coils.

WARNING ELECTRICAL INFORMATION

• The complete electrical rating of your new room air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements.
• Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards.
• Your air conditioner must be plugged into a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle.
• Do not run the air conditioner with a protective covering. This could result in mechanical damage to the air conditioner.
• Do not use an extension cord or an adapter plug-

ENERGY SAVING IDEAS

• The capacity of the room air conditioner must fit the room size for efficient and satisfactory operation.
• Install the room air conditioner on the shady side of your home. A window that faces north is best because it is shaded most of the day.
• Do not block air conditioner flow inside with blinds, curtains, or furniture, or outside with shrubs or enclosures. or other buildings.
• Close the floor and wall registers and the fireplace damper so cool air does not escape up the chimney or into the ductwork.
• Keep blinds and drapes in other windows closed during the sunniest part of the day.
• Clean the air filter as recommended in the MAINTENANCE section of this manual.
• Proper insulation and weather stripping in your home will help keep warm air out and cool air in.
• External house shading with trees, plants, or awnings will help reduce the air conditioner’s workload.
• Operate heat-producing appliances such as ranges, washers, dryers, and dishwashers during the coolest part of the day.

ELECTRICAL REQUIREMENTS

• OBSERVE ALL LOCAL CODES AND ORDINANCES.
• DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER SUPPLY CORD GROUND PRONG.
• ELECTRICAL GROUND IS REQUIRED ON THIS APPLIANCE.
• A 250-volt 60 Hz, AC only, 20A fused and properly grounded electrical supply is required.
• A time-delay fuse or time-delay circuit breaker is recommended. Use a dedicated circuit, serving only this appliance.
• DO NOT USE AN EXTENSION CORD.

RECOMMENDED GROUNDING METHOD

For your safety, this appliance must be grounded. This appliance has a power supply cord with a 3-prong grounding plug. To minimize possible shock hazards, the cord must be plugged into a mating grounding-type wall receptacle and grounded by the National Electrical Code (ANSI/NFPA 70) edition and all local codes and ordinances. If a mating wall receptacle is not available, it is the personal responsibility and obligation of the customer to have a properly grounded 3-prong wall receptacle installed by a qualified electrician.

NOTE: The shape may be different according to its model,

INSTALLING THE POWER CORD

You can choose between the two methods below according to your window stool shape and preference.

• **USING SLIT “A”***
  • Fasten the stopper using 1 screw hole, and lead out the power cord through slit “A”,
• **USING SLIT “B”***
  • Fasten the stopper using the left screw hole, and rotate properly to lead the power cord out through slit “B”.

INSTALLATION REQUIREMENTS

Your air conditioner will be installed into standard double-hung windows with actual clear opening widths of 23 to 36 inches (584 mm to 914mm) (FIG. 1)- The lower sash must open sufficiently to allow a clear vertical opening of 15 inches (381mm). Side louvers and the rear of the air conditioner must have clear air space to allow enough airflow through the condenser for heal removal. The rear of the unit must be outdoors, not inside a building or garage.

ELECTRICAL SERVICE

• Check your available electrical service. The power supply available must be the same as that shown on the unit nameplate (found on the right side of the cabinet).
• All models are equipped with a 3-prong service plug to provide proper service and safe positive grounding. Do not change the plug in any way. Do not use an adapter plug. If your present wall outlet does not match your plug, call a qualified electrician to make the necessary corrections.
• SAVE CARTON and this OWNER’S MANUAL for future reference. The carton is the best way to store the unit during winter or when not in use.

CAUTION

• To avoid the risk of personal injury, property damage, or product damage due to the weight of this device and sharp edges that may be exposed:
• Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit. To prevent injury or strain, use proper lifting and carrying techniques when moving the unit.
• Carefully inspect the location where the air conditioner will be installed. Be sure it will support the weight of the unit over an extended period.
• Handle the air conditioner with care. Wear protective gloves whenever lifting or carrying the unit. AVOID the sharp metal fins of the front and rear colls.
• Make sure the air conditioner does not fall during installation.

INSTALLATION HARDWARE

REQUIRED TOOLS

• Tight Fitting gloves
• Standard screwdriver
• Phillips screwdriver
• Pliers
• Sharp knife
• 3/8-inch open-end wrench or adjustable wrench
• 1/4 inch hex socket and ratchet
• Tape measure
• Electric drill
• 1/4-inch drill bit

INSTALLATION
Pick a location that will allow you to blow the cold air into the area you want. Windows used for installation must be strong enough to support the weight of the air conditioner. Good installation with special attention to the proper position of the unit will lessen the chance that service will be needed. When cooling more than one room, the installation location is very important. To cool your rooms, cold air must be blown from the air conditioner in a straight path.

HOW TO INSTALL

1. If the air conditioner is blocked by a storm window frame, see step 19 on page 8 before beginning to install.
2. Slide the unit out of the cabinet by gripping the base pan handle and pulling forward while bracing the cabinet.
3. Cut the FOAM SEAL (ITEM I) to fit the underside of the window sash. Peel off the backing and attach the FOAM SEAL as shown in Fig. 5.
4. Insert the side curtain (ITEM A) into the upper guide and lower guide of the air conditioner, Fasten the curtains to the unit with screws (ITEM E).
5. Open the window. Mark a line on the center of the window’s inner sill. Carefully place the cabinet on the window inner sill and align the center of the cabinet front with the center line marked on the window inner sill.
6. Pull the bottom window sash down behind the upper guide until they meet.
   • NOTE: Do not pull the window sash down so tightly that the movement of the side curtain is restricted.
7. Loosely assemble the sill supports using the parts in FIG 9.
8. Select the position that will place the sill supports near the outermost point on the sill (FIG. 10). Attach the sill supports to the cabinet track hole closest to the selected position using a screw (ITEM t).
9. Place the sill supports with the cabinet on the window sill’s selected position.
10. The cabinet should be installed with a very slight tilt (about 1/4″) downward toward the outside (FIG. 11). Adjust the bolts and the nuts of sill supports to level the cabinet.
11. Attach the cabinet to the inner sill by driving the screws (ITEM F) through the Lower Guide into the window’s inner sill (FIG. 12).
12. Pull each side curtain fully to each side of the window opening. Attach each side curtain to the window sash using screws (ITEM G). (FIG. 13)
13. Attach the L BRACKET (ITEM J) with the screw (ITEM G). (FIG. 14)
14. DRAINAGE Be sure to insert the drain pipe into the base pan before installation. The air conditioner must be installed with a slight tilt (1/4*) downward to the outside for proper drainage of excess condensed water through the drain pipe. (FIG. 15)
15. Slide the chassis into the cabinet. (FIQ. 16)
    • CAUTION: For security purposes, reinstall the side screws you removed in Step 1.
16. Cut the foam strip (ITEM H) to the proper length and insert it between the upper window sash and the lower window sash. (FIG. 17)
17. The vent control handle must be straightened before the decorative front is attached. Pull out part A to align with part B.
18. FRONT INSTALLATION
    • Install the front grille(packed separately) onto the cabinet as follows:
    • hook the upper tabs of the front grille into slots on the cabinet top. (FIG, 19)
    • Push the front grille’s tips towards the cabinet to snap side tabs into the cabinet. (FIG. 19)
    • Open the inlet grille. (FIG. 20)
    • Install the screw (ITEM E) through the front grille. (FIG. 20)
    • Close inlet grille. (FIG. 21)
19. IF THE AIR CONDITIONER IS BLOCKED BY STORM WINDOW FRAME
    • If a storm window presents interference, fasten a 2* wide wood strip to the inner window sill across the full width of the sill.
    • The wood strip should be thick enough to raise the height of the window sill so that the unit can be installed without interference from the storm window frame. See FIG. 22.
    • The top of the wood strip should be approximately 3/4* higher than the storm window frame to help condensation drain properly to the outside.
    • Install a second wood strip (approximately 6* long by 1/2″ wide and the same thickness as the first strip) in the center of the outer sill flush against the back of the inner sill. Screw the L brackets into this strip.
    • This will raise the L bracket as shown in FIG. 22.

REMOVAL FROM WINDOW

• Turn off and unplug the air conditioner.
• Remove the front grille. See HOW TO REMOVE THE FRONT GRILLE. Refer to page 13.
• Unscrew the side screws that you installed in Step 15,
• Slide the air conditioner out of the cabinet. BE CAREFUL NOT TO DROP IT. Hold onto it firmly the whole way sliding it out. Once removed, set it safely out of the way.
• Remove the & bracket from the window frame and the sash seal from between the windows.
• Unscrew the side curtains from the window frame. Fold them back to the sides of the cabinet.
• Remove screws attaching cabinet to inner sill. Be careful not to let the cabinet fail once the screws are removed.
• Remove the cabinet from the window opening.
• Place the air conditioner into the cabinet. Reinstall side screws and Ftont Grille.
• Place the unit and all assembly hardware in an air conditioner shipping carton, and store them in a clean, dry place.

CAUTION

• Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit.
• To prevent injury or strain, use proper lifting and carrying techniques when moving the unit.
• When handling the air conditioner, be careful to avoid cuts from sharp metal fins on the front and rear colls.
• Make sure air conditioner does not fall during removal.

OPERATION

HOW AND WHY

• Your room air conditioner provides the following functions to make hot-weather living more comfortable:
  • Cools and circulates room air.
  • Lowers humidity by removing excess moisture.
  • Filters out summertime dust, dirt, and some airborne impurities.
  • The air conditioner performs these functions by drawing room air through a filter that traps dust and dirt particles. The air then passes over a cooling coil which refrigerates the air and removes excess moisture.
  • The same air is then returned to the room- cooler, drier, and cleaner. Moisture removed from the room air is carried to the outside and evaporated.
  • Your air conditioner is designed to be easy to operate and to provide plenty of cooling power.

NORMAL SOUNDS FIG. 23

• Aside from the regular fan motor and compressor sounds coming from your air conditioner, you will once in a while hear a pinging sound. This is the result of moisture being picked up from the air in the room and thrown against the air conditioner’s fan.
• This is normal and should not be cause for concern.
• Also, do not be alarmed if you hear a slight hissing or gurgling sound coming from your air conditioner after it is off. These are normal coolant noises.

CAPACITY AND RUNNING TIME

• Proper unit size is important in deciding the desired comfort for the area you want to cool. The proper size is determined by the number of square feet in the area to be cooled, indoor and outdoor temperature and humidity.
• Whenever the heat or humidity load is above normal the air conditioner must run longer and more often to keep the desired temperature you have selected,
• Under heavy heat load conditions, the air conditioner may need to run constantly to keep the temperature you want.
• At times using the MED FAN setting to circulate the room air may make it comfortable even though the air is not being cooled. This will decrease your cost of use.

FEATURES

1. Cabinet
2. Vertical Air Direction Louvers
3. Horizontal Air Direction Louvera
4. Inlet Grille
5. Air Filter
6. Front Grille
7. Control Panel
8. Power Cord
9. Evaporator Coll
10. Condenser
11. Compressor
12. Base pan
13. Brace
14. Upper Guide
15. Curtain
16. Remote Control

USING THE AIR CONDITIONER

WARNING To reduce the risk of fire, electric shock, or injury to persons, read the important SAFETY instructions section before operating this appliance To begin operating the air conditioner after installation, follow these steps:

1. Plug in the air conditioner, (To prevent electrical hazards, do not use an extension cord or an adapter plug.)
2. Set the exhaust vent to the CLOSE position.
3. Set the TEMP Control to the coolest setting.
4. Set the MODE control at the highest COOl level.
5. Adjust the louvers for comfortable airflow,
6. Once the room has cooled, adjust the TEMP and Mode Control to the setting you find most comfortable.

Note: if the air conditioner is turned off, wait 3 minutes before restarting. This allows the pressure inside the compressor to equalize. Failure to wait 3 minutes before restarting may cause inefficient operation. If you move the TEMP Control to a warmer, then immediately back to a cooler setting, the unit will shut off, Wait 3 minutes before restarting.

VENT CONTROL

• The Vent Control allows the air conditioner to either recirculate inside air (CLOSE) or exhaust air to the outside (OPEN). (FIG. 25)
• The CLOSE position is used when maximum cooling is desired. It may also be used for air recirculation without cooling when the air conditioner is set in the FAN position.
• The OPEN position removes stale air from the room and exhausts it to the outside. Fresh air is drawn into the room through your home’s normal air passages:
• The OPEN or CLOSE position can be used with any mode selection.

DISPLAY

AUTO RESTART
In the failure of electric power, the unit runs as in the previous setting operation.

HORIZONTAL AIR DIRECTION CONTROL

• The horizontal air direction is adjusted by moving the vertical louvers right and left with your fingertips. (FIG. 26)

VERTICAL AIR DIRECTION CONTROL

• The vertical air direction is adjusted by moving the horizontal louvers up and down with your fingertips. (FIG.27)

REMOTE CONTROL

NOTE: The Remote Control will not operate properly if a strong light shines on the sensor window of the Air Conditioner or if there are obstacles between the Remote Control and the Air Conditioner, Every time you push the button, you will hear a beep from the Air Conditioner.

HOW TO INSERT BATTERIES INTO THE REMOTE CONTROL

1. Remove the cover from the back of the remote controller.
   • Open the cover according to the arrow direction on the cover.
2. Insert two batteries.
   • Be sure that the (+) and (-) directions are correct.
   • Be sure that both batteries are new.
3. Re-attach the cover.
   • Do not use rechargeable batteries: Such batteries differ from standard dry cells in shape, dimensions, and performance.
   • Remove the batteries from the remote controller if the air conditioner is not going to be used for an extended length of time.

MAINTENANCE

AIR FILTER CLEANING
The Air Filter will become dirty as it removes dust from the inside air. It should be washed at least every 2 weeks. If the Air Filter remains full of dust, the airflow will decrease and the cooling capacity will be reduced, possibly damaging the unit.

• Pull the inlet grille forward, grasping both tabs, then pull out the air filter. (FIG. 28)
• Wash the Air Filter under the faucet with warm water. Be sure to shake off all the water before replacing the filter, (FIG.29)

AIR CONDITIONER CLEANING

• Clean the front grille and inlet grille by wiping with a cloth dampened in a mild detergent solution.(FIG30)
• The cabinet may be washed with mild soap or detergent and lukewarm water, then polished with liquid appliance wax.
• To ensure continued peak efficiency, the condenser coils (outdoor side of the unit) should be checked periodically and cleaned if they become clogged with soot or dirt from the atmosphere. Brush or vacuum exterior coils to remove debris from fins.

HOW TO REMOVE THE FRONT GRILLE

• Open the inlet grille downward.
• Remove the screw securing the Front Grille.
• Push the grille up from the bottom and pull the top of the grille away from the case to lift the top tabs out of their slots.

HOW TO REPLACE THE FRONT GRILLE

• Attach the front grill to the cabinet by inserting the tabs on the grille into the slots on the front of the cabinet. Push the grille in until it snaps into place.

TROUBLESHOOTING

BEFORE CALLING FOR SERVICE
Check the following list to be sure a service call is really necessary. A quick reference to this manual may help you avoid an unneeded service call.

MORE INFO

• Shop genuine replacement parts for Kenmore 580.76081700
• Find Your Kenmore Air Conditioner Parts – Select From 261 Models

Get it fixed, at your home or ours! Your Home

• For repair – in your home- of all major brand appliances, lawn and garden equipment, or heating and cooling systems, no matter who made it, no matter who sold it!
• For the replacement parts, accessories, and owner’s manuals you need to do it yourself.
• For Sears professional installation of home appliances and items like garage door openers and water heaters.
• 1-800-4-MY-HOME® (1-800-469-4663)
• Call anytime, day or night (U.S.A. and Canada)
• www.sears.com.
• www.sears.ca.
• Our Home

For repair of carry-in items like vacuums, lawn equipment, and electronics, call or go online for the location of your nearest

• Sears Parts & Repair Center.
• 1-800-488-1222
• Call anytime, day or night (U.S.A. only)
• www.sears.com.

To purchase a protection agreement(U.S.A.) or maintenance agreement(Canada) on a product serviced by Sears:

• 1-800-827-6655 (U.S.A.)
• 1-800-361-6665 (Canada)

Registered Trademark / TV Trademark /*M Service Wark of Sears, Roebuck and Cc.

References

• Repair Your Grill: Shop Replacement Parts for 24,880 Models
• Kenmore Air Conditioner Parts - Select From 261 Models

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>