motorola XT2435-1 Mobile Cellular Phone User Guide

motorola XT2435-1 Mobile Cellular Phone

Product Information

Specifications

• Product Model: XT2435-1, XT2435-2, XT2435-3
• Product ID: XXXXXXXX
• Manual Number: XXXXXXXX-A

Description
The product is a mobile phone manufactured by Motorola. It features a sleek design, user-friendly interface, and supports various applications and services.

Features

• Supports SIM card(s)
• Optional microSD card slot for additional storage
• Power button for device control
• Prompts for easy setup

Product Usage Instructions

Put in the Cards & Power On:

1. Insert the SIM tool into the hole next to the tray to pop out the tray. Ensure you use the correct size SIM card and avoid cutting the SIM card.
2. Insert the SIM card(s) with the gold contacts facing down, then gently push the tray into the slot. Optionally, add a microSD card for additional storage (sold separately).
3. Press and hold the Power button to turn on your phone. Follow the on-screen prompts to complete the setup process.

Note: To turn off your phone, press the Power and Volume Up buttons simultaneously.

Help & More
For further assistance, product support, or additional information, please refer to the product manual provided with your device or visit the official Motorola website at www.motorola.com.

Frequently Asked Questions (FAQ)

• Q: Where can I find the product ID and model number?
  

  • A: The product ID and model number can be found on the device itself or in the product manual under the specifications section.

• Q: How do I insert a SIM card?
  

  • A: Use the SIM tool provided to pop out the tray, insert the SIM card with the gold contacts facing down, and gently push the tray back in. Avoid cutting the SIM card.

• Q: Can I use a microSD card for additional storage?
  

  • A: Yes, you can insert a microSD card (sold separately) into the designated slot for additional storage capacity.

WWW.ENVISIONLEDLIGHTING.COM

Undercabinet Installation Instructions

MOUNTING FIXTURE

1. Remove captive mounting screw covers.
2. Place fixture in desired position and drive mounting screws securely. In some installations it may be desired to drill a pilot hole for the screws.
3. Replace the captive mounting screw cover.

POWER CORD CONNECTION
Remove the electrical port cover and insert the power cord into INPUT electrical port. (Power cord sold seperately)

JOINING MULTIPLE FIXTURES

USING JUMPER CORD

1. Remove electrical port covers.
2. Connect INPUT of jumper cord to INPUT of electrical port.
3. Connect OUTPUT of jumper cord to OUTPUT of electrical port.

USING END-TO-END CONNECTOR

1. Remove electrical port covers.
2. Connect INPUT of end-to-end connector to INPUT of electrical port.
3. Connect OUTPUT of end-to-end connector to OUTPUT of electrical port.

SWITCH CONNECTION

1. Open the cover on the back using a flat and sharp tool. (Fig. 1)
2. Unscrew a P2 connector where 4 black wires are connected. (Fig. 2)
3. Use a P2 connector (provided) and connect an INPUT port wire (Black) and a wire from the switch. (Fig. 2)
4. Use another P2 connector (provided) and connect a wire from Switch and the remaining black wires. (Fig. 2)
5. Replace the cover.

WIRING CONNECTION THROUGH A REAR ACCESS DOOR

1. Loosen screw that secures rear access door and remove the door from key hole by just a slide (Fig. 3)
2. Assemble 3/8″ die-cast connector into rear access door (Fig. 4) and push supply cable through the die-cast connector. (Fig. 5)
3. Inside fixture are three wires with push-in connectors. Carefully pull these out of fixture. Do not pull with excessive force.
4. Insert each of the three wires from the supply cable into each of the three push-in connectors with color wires. Black to Black, White to White and Green (Earth Wire) to green.
5. Neatly push wires and push-in connectors into opening the back of the fixture.
6. Close the rear access door and tighten screw.

1. Open a cover in the back using a flat and sharp tool.
2. Remove knockout and assemble 3/8″ die-cast connector.
3. Push supply cable through the die-cast connector and connect wires using push-in connector.
4. Replace the cover and close.

References

• motorola | Smartphones, Accessories & Smart Home Devices
• Motorola México | Tienda oficial - Tienda en línea
• Motorola legal
• Country Selector | Motorola Support US
• SAR Information | Motorola Support US

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>