PPE 318035200 Ford 6.0L Power Stroke Main Stud Kit Installation Guide
- June 30, 2024
- PPE
Table of Contents
318035200 Ford 6.0L Power Stroke Main Stud Kit
“`html
Specifications:
- Product: Ford 6.0L Power Stroke Main Stud Kit
- Part Number: 318035200
Product Usage Instructions:
Inspection and Preparation:
Prior to installation, inspect for any damage or defects. Clean
all hardware and verify the product part number matches your
application. Ensure the kit is complete with no missing parts.
Thread Preparation:
Clean all threads in the engine block. Use a bottoming thread
chaser if necessary to ensure proper thread engagement and accurate
torque readings.
Stud Installation:
-
Install Inner (A) and outer Studs (B) into the block,
hand-tighten without tools (equivalent of 20-30 lb-in). -
Install main caps and check for proper alignment.
Nut Installation:
Lubricate the threads of all M14 Nuts with the Assembly
Lubricant provided. Install the Nuts onto the Studs.
Tightening Procedure:
Tighten M14 Nuts in three steps using the torque sequence
provided: 60 lb-ft, 120 lb-ft, and finally 180 lb-ft.
Tighten all M8 Bedplate Outer Bolts to 25 lb-ft.
FAQ:
Q: Can I use Loctite for mounting?
A: Yes, Loctite may be used for permanent mounting. Ensure
torque sequences are completed before Loctite hardens.
Q: What should I do if I encounter drive-train failure after
installing this kit?
A: Performance products can increase stress on drive-train
components. Ensure proper installation and consult a professional
if issues arise.
“`
PPEpower.com
2003 – 2007 Ford 6.0L Power Stroke Main Stud Kit
(318035200)
Installation Guide
Rev: 06/17/24 | v1
ATTENTION: We recommend the installation of this part be done by a trained
professional Ford technician. PPE will not accept liability for damage
resulting from incorrect assembly. These instructions are not intended as a
service or overhaul manual. These instructions are intended to facilitate the
modification of non-factory parts installation by a trained professional.
A
B
C E
D
CONTENTS A: (10) M14 STUD 143 MM LENGTH B: (10) M14 STUD 131 MM LENGTH C:
(8) M8 12-PT BOLT D: (20) M14 NUT E: (1) ASSEMBLY LUBRICANT
Ford 6.0L Power Stroke Main Stud Kit
Prior to installation, please inspect for any damage or defects and clean all
hardware. Verify product part number matches your application. Make sure the
kit is complete with no missing parts.
NOTE: Loctite may be used for permanent mounting. Torque sequences must be
complete prior to Loctite hardening.
Clean all threads in the engine block. Use a bottoming thread chaser if
necessary. This would ensure thread engagement and more accurate torque
readings.
Install Inner (A) and outer Studs (B) into the block. Hand-tighten without
tools (equivalent of 20-30 lb-in.). Install main caps and check for proper
alignment.
Lubricate the threads of all M14 Nuts with the Assembly Lubricant provided.
Install the Nuts onto the Studs.
Tighten M14 Nuts in three steps using the torque sequence shown in the image
below. Torque specs for each step are: 60 lb-ft, 120 lb-ft, and 180 lb-ft
(final).
Tighten all M8 (21-28) Bedplate Outer Bolts to 25 lb-ft.
Front of Engine
28
24
21
25
18
120
2
8
16
17
9
1
7
15
19
11
3
5
13
20
12
4
6
14
27
23
22
26
DISCLAIMER OF LIABILITY
Performance products can increase horsepower above and beyond factory
specifications. Additional horsepower creates more stress on the drive-train
components, which could result in drive-train failure.
Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE
LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR
REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
This agreement sets forth the terms and conditions for the use of PPE
products. The installation of this product indicates that the Buyer has read
and understands this agreement and accepts the terms and conditions. PPE
(Pacific Performance Engineering) Inc., its distributors, employees, and
dealers (the “Seller”) shall not be responsible for the product’s proper use
and service. The buyer hereby waives all liability claims. The Buyer hereby
acknowledges no reliance on the Seller’s skill or judgment to select or
furnish goods suitable for any particular purpose and that there are no
liabilities which extend beyond the description on the face hereof, and the
Buyer hereby waives all remedies or liabilities expressed or implied, arising
by law or otherwise (including without any obligation of the Seller with
respect to fitness, merchantability and consequential damages), or whether or
not occasioned by the Seller’s negligence. The Seller disclaims any warranty
and expressly disclaims any liability for personal injury or damages. The
Buyer acknowledges and agrees that the disclaimer of any liability for
personal injury is a material term for this agreement and the Buyer agrees to
indemnify the Seller and to hold the Seller harmless from any claim related to
the item of equipment purchased. Under no circumstances will the Seller be
liable for any damages or expenses by reason of use or sale of any such
equipment. The Seller assumes no liability regarding the improper installation
or misapplication of its products. It is the installer’s responsibility to
check for proper installation and if in doubt, contact the manufacturer. The
Buyer is solely responsible for all warranty issues from the manufacturer.
LIMITATION OF WARRANTY
The Seller gives Limited Warranty as to description, quality, merchantability,
and fitness for a particular purpose, productiveness, or any other matter of
Seller’s product sold herewith. The Seller shall not be responsible for the
products proper use and service and the Buyer hereby waives all rights other
than those expressly written herein. This warranty shall not be extended,
altered or varied except by a written instrument signed by Seller and Buyer.
Limited lifetime warranty on all PPE cast aluminum products, and PPE
Transmission Coolers. Three (3) year limited warranty on PPE Manifolds and Up-
Pipes Kits, and OEM-Length Up-Pipes. One (1) year limited warranty on all
other PPE products from the date of sale to original buyer and limited solely
to the parts contained within the products kit. All products that are in
question of Warranty must be returned prepaid to the Seller and must be
accompanied by a dated proof of purchase receipt. All Warranty claims are
subject to approval by Seller. Under no circumstances will the Seller be
liable for any labor charged or travel time incurred in diagnosis for defects,
removal, or re-installation – of this product or any other contingent
expenses. Under no circumstances will the Seller be liable for any damage or
expenses incurred by reason of the use or sale of any such equipment. In the
event that the buyer does not agree with this agreement: the buyer may
promptly return this product, in a new and unused condition in its original
packaging, with a dated proof of purchase to the place of purchase within ten
(10) days from date of purchase for a full refund. The installation of this
product indicates that the buyer has read and understands this agreement and
accepts its terms and conditions.
PPEpower.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>