PPE 128051000 Heavy-Duty Cast Aluminum Deep Transmission Pan Installation Guide
- June 8, 2024
- PPE
Table of Contents
PPE 128051000 Heavy-Duty Cast Aluminum Deep Transmission Pan
CAUTION:
The PPE Transmission Pan is designed to fit the factory Allison 1000
transmission (supplied as original equipment). However, in some applications,
or because of the use of certain factory options and/or aftermarket equipment,
there may be clearance problems between your PPE DEEP Transmission Pan and
other vehicle components.
It is the responsibility of the vehicle owner and installer to ensure that there is no contact between the pan and other moving or fixed vehicle components. Contact with any vehicle component or the modifying of the PPE Transmission Pan voids the pan warranty. PPE assumes no liability, expressed or implied, for damage or injury to persons or property.
KIT INCLUDES
- A (1) PPE DEEP Transmission Pan
- B (1) DEEP Transmission Filter
- C (12) M8 – 1.25 x 30 Allen Bolts with washers
- D (1) 1/4” NPT plug (installed)
- E (1) 1/8” NPT plug (installed)
- F (1) Neodymium Magnetic Drain Plug (installed)
TOOLS AND PARTS REQUIRED
- Torque Wrench
- 1/4” Ratchet
- 1/4” Extension
- 1/4” Drive 6mm Allen Socket
- 17mm Socket for Service/ Draining
- Oil Drain Pan
- Shop Towels
- Gloves
- Eye Protection
Installation Instructions
-
Step 1:
Remove the 12 bolts holding the pan in place. -
Step 2:
Clean reusable gasket. Set to the side for reassembly in Step 7. -
Step 3:
Remove the filter by gripping it as shown and pulling it straight out. -
Step 4:
Remove the orange filter seal from the transmission housing.
-
Step 5:
Preassemble hardware. -
Step 6:
Insert the new filter and make sure it is straight. -
Step 7:
Thoroughly clean the reusable factory gasket and install it on the pan. -
Step 8:
Place 2 bolts thru the gasket and pan to hold the gasket in place. Hold assembly and position to align with transmission case. Tighten two bolts finger tight to hold the pan in place. -
Step 9:
Install remaining bolts. Torque bolts to 15 ft. lbs. using the crossing- pattern sequence shown below.
Fill with the recommended fluid. Check for leaks. Installation complete.
DISCLAIMER OF LIABILITY
Performance products can increase horsepower above and beyond factory specifications. Additional horsepower creates more stress on the drive-train components, which could result in drive-train failure.
Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
This agreement sets forth the terms and conditions for the use of PPE products. The installation of this product indicates that the Buyer has read and understands this agreement and accepts the terms and conditions. PPE (Pacific Performance Engineering) Inc., its distributors, employees, and dealers (the “Seller”) shall not be responsible for the product’s proper use and service. The buyer hereby waives all liability claims. The Buyer hereby acknowledges no reliance on the Seller’s skill or judgment to select or furnish goods suitable for any particular purpose and that there are no liabilities that extend beyond the description on the face hereof, and the Buyer hereby waives all remedies or liabilities expressed or implied, arising by law or otherwise (including without any obligation of the Seller with respect to fitness, merchantability, and consequential damages), or whether or not occasioned by the Seller’s negligence.
The Seller disclaims any warranty and expressly disclaims any liability for personal injury or damages. The Buyer acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the Buyer agrees to indemnify the Seller and to hold the Seller harmless from any claim related to the item of equipment purchased. Under no circumstances will the Seller be liable for any damages or expenses by reason of the use or sale of any such equipment. The Seller assumes no liability regarding the improper installation or misapplication of its products. It is the installer’s responsibility to check for proper installation and if in doubt, contact the manufacturer. The Buyer is solely responsible for all warranty issues from the manufacturer.
LIMITATION OF WARRANTY
The Seller gives Limited Warranty as to description, quality, merchantability, and fitness for a particular purpose, productiveness, or any other matter of Seller’s product sold herewith. The Seller shall not be responsible for the product’s proper use and service and the Buyer hereby waives all rights other than those expressly written herein. This warranty shall not be extended, altered, or varied except by a written instrument signed by Seller and Buyer.
Limited lifetime warranty on all PPE cast aluminum products, and PPE Transmission Coolers. Three (3) year limited warranty on PPE Manifolds and Up- Pipes Kits and OEM-Length Up-Pipes. One (1) year limited warranty on all other PPE products from the date of sale to the original buyer and limited solely to the parts contained within the products kit. All products that are in question of Warranty must be returned prepaid to the Seller and must be accompanied by a dated proof of purchase receipt. All Warranty claims are subject to approval by Seller. Under no circumstances will the Seller be liable for any labor charged or travel time incurred in diagnosis for defects, removal, or re- installation – of this product or any other contingent expenses.
Under no circumstances will the Seller be liable for any damage or expenses incurred by reason of the use or sale of any such equipment. In the event that the buyer does not agree with this agreement: the buyer may promptly return this product, in a new and unused condition in its original packaging, with a dated proof of purchase to the place of purchase within ten (10) days from date of purchase for a full refund. The installation of this product indicates that the buyer has read and understands this agreement and accepts its terms and conditions.