PPE 214053010 Heavy-Duty Cast Aluminum Engine Oil Pan Installation Guide
- June 8, 2024
- PPE
Table of Contents
PPE 214053010 Heavy-Duty Cast Aluminum Engine Oil Pan Installation Guide
FEATURES
**
CONTENTS**
- A (1) Engine Oil Pan
- B (1) Neodymium magnet equipped drain plug with copper washer (installed)
- C (2) M6 x 1.0 x 25mm locating studs
- D (14) M6 x 1.0 x 25mm socket head cap screws
- E (14) M6 x 1.0 x 25mm zinc coated flat washers
PREPARATION
Step 1 Vehicle off. Engine cool.
Step 2 Remove stock drain plug and drain oil completely. Overnight if possible.
Step 3 Replace stock drain plug. Pry away stock pan from housing. (FIG 1 ) Use caution when removing pan. There will be oil at the bottom of the pan
Step 4 Remove stock locating stud.
Step 5 Thoroughly clean mating surface. Clean oil off the oil pickup and
surrounding area . (FIG 2)
Step 6 Install new oil filter if needed.
INSTALLATION
Step 1 Install Locating Studs (F) on opposite sides of the flange. (FIG
3)
Step 2 Apply a continuous bead of RTV silicone in the machined grooves
and around screw holes. (FIG 4)
Step 3 Pre-assemble screw and washer hardware (C, D) for easier installation.
Step 4 Using the installed Locating Studs as guides, carefully install the Oil Pan until it contacts the housing surface. Use care not to smear the silicone. Install one set of assembled screw and washer assemblies (C, D) on either side of the Oil Pan to secure the Pan. Finger tight for now
Step 5 Remove Studs. Install remaining screw and washer assemblies (C,
D). Finger tight for now.
Step 6 Tighten in a crossing pattern as shown (FIG 5 ). Torque to 8 ft. lbs./89 in. lbs.
Step 7 Check NPT Plug and Drain Plug. Tighten if necessary.
Step 8 Allow silicone to set up for 1 hour before filling with vehicle manufacturer’s recommended engine oil.
Step 9 Start engine. Check for leaks. Top off oil if necessary
Engine oil service
The flat bottom of your PPE Pan allows for complete drainage. At this time the Neodymium magnet should be checked for excessive metal particles. Some is normal. Excessive debris may indicate a problem. Wipe off Drain Plug to remove particles. Reinstall and tighten to 18 ft. lbs.
DISCLAIMER OF LIABILITY
Performance products can increase horsepower above and beyond factory specifications. Additional horsepower creates more stress on the drive-train components, which could result in drive-train failure.
Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
This agreement sets forth the terms and conditions for the use of PPE products. The installation of this product indicates that the Buyer has read and understands this agreement and accepts the terms and conditions. PPE (Pacific Performance Engineering) Inc., its distributors, employees, and dealers (the “Seller”) shall not be responsible for the product’s proper use and service. The buyer hereby waives all liability claims. The Buyer hereby acknowledges no reliance on the Seller’s skill or judgment to select or furnish goods suitable for any particular purpose and that there are no liabilities which extend beyond the description on the face hereof, and the Buyer hereby waives all remedies or liabilities expressed or implied, arising by law or otherwise (including without any obligation of the Seller with respect to fitness, merchantability and consequential damages), or whether or not occasioned by the Seller’s negligence. The Seller disclaims any warranty and expressly disclaims any liability for personal injury or damages. The Buyer acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the Buyer agrees to indemnify the Seller and to hold the Seller harmless from any claim related to the item of equipment purchased. Under no circumstances will the Seller be liable for any damages or expenses by reason of use or sale of any such equipment. The Seller assumes no liability regarding the improper installation or misapplication of its products. It is the installer’s responsibility to check for proper installation and if in doubt, contact the manufacturer. The Buyer is solely responsible for all warranty issues from the manufacturer.
LIMITATION OF WARRANTY
The Seller gives Limited Warranty as to description, quality, merchantability, and fitness for a particular purpose, productiveness, or any other matter of Seller’s product sold herewith. The Seller shall not be responsible for the products proper use and service and the Buyer hereby waives all rights other than those expressly written herein. This warranty shall not be extended, altered or varied except by a written instrument signed by Seller and Buyer.
The Warranty on PPE Manifolds and Up-Pipes Kits, OEM-Length Up-Pipes is three (3) years, a limited lifetime warranty on PPE cast aluminum pans and covers, and a limited lifetime warranty on PPE Transmission Coolers and one (1) year limited warranty on all other PPE products from the date of sale to original buyer and limited solely to the parts contained within the products kit. All products that are in question of Warranty must be returned prepaid to the Seller and must be accompanied by a dated proof of purchase receipt. All Warranty claims are subject to approval by Seller. Under no circumstances will the Seller be liable for any labor charged or travel time incurred in diagnosis for defects, removal, or re-installation – of this product or any other contingent expenses. Under no circumstances will the Seller be liable for any damage or expenses incurred by reason of the use or sale of any such equipment. In the event that the buyer does not agree with this agreement: the buyer may promptly return this product, in a new and unused condition in its original packaging, with a dated proof of purchase to the place of purchase within ten (10) days from date of purchase for a full refund. The installation of this product indicates that the buyer has read and understands this agreement and accepts its terms and conditions.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>