PPE 158207000 Heavy Duty Forged Tie Rod Assemblies Installation Guide

June 1, 2024
PPE

PPE 158207000 Heavy Duty Forged Tie Rod Assemblies

PPE-158207000-Heavy-Duty-Forged-Tie-Rod-Assemblies-
product

Specifications

  • Product: Heavy-Duty Forged Tie Rod Assemblies
  • Model Numbers: 158207000, 158219000, 158214000
  • Installation Guide Revision: 12/29/23 | Version: 4

Product Information

The Heavy-Duty Forged Tie Rod Assemblies are designed to provide enhanced durability and performance for your vehicle’s steering system. Made from high- quality materials, these tie rod assemblies offer improved strength and reliability compared to stock components.

Installation Instructions

  1. Ensure the vehicle is off, in Park with the Parking Brake applied on a level surface. Jack up the vehicle and secure it. Remove the front wheels.
  2. Remove the nut at the end of the stock spindle. Use a tie rod fork tool to remove the tie rod ball stud from the steering knuckle.
  3. Remove the stock retention clamps holding the inner boot in place. Pull back the boot and unscrew the inner tie rod to remove it.
  4. Measure the stock tie rod length and adjust the Heavy-Duty Forged Tie Rod Assembly to match. Tighten the Jam Nut to 55 lb-ft.
  5. If equipped, detach the grease fitting from the inner tie rod for maintenance purposes only.
  6. Apply red thread locker to the threaded inner and tighten it. Slide the boot over the inner tie rod and secure both clamps.
  7. Install the ball pin into the steering knuckle and tighten the Lock Nut to 45 lb-ft.
  8. Repeat the installation procedure on the passenger side.
  9. Have the vehicle professionally aligned after installation.

Frequently Asked Questions (FAQ)

  • Q: Can these tie rod assemblies be used on any vehicle?
    A: These assemblies are designed for specific models and should be used accordingly. Check compatibility before installation.

  • Q: Do I need specialized tools for installation?
    A: Basic automotive tools are required for installation. A tie rod fork tool or equivalent may be needed for certain steps.

PPEpower.com

Heavy-Duty Forged Tie Rod Assemblies
(158207000)(158219000)(158214000)

Installation Guide
Rev:12/29/23 | v4

CONTENTS

A (2) Heavy-Duty Forged Tie Rod Assemblies

PPE-158207000-Heavy-Duty-Forged-Tie-Rod-Assemblies-
\(2\)

INSTALLATION:

  1. Vehicle off and in Park with Parking Brake applied on a level surface. Jack up the vehicle and secure. Remove front wheels. Fig.1PPE-158207000-Heavy-Duty-Forged-Tie-Rod-Assemblies- \(3\)

  2. Factory Outer Tie Rod – Remove nut at the end of the stock spindle. Use a tie rod fork tool or equivalent to remove tie rod ball stud from tapered hole in steering knuckle. Fig.2PPE-158207000-Heavy-Duty-Forged-Tie-Rod-Assemblies- \(4\)

  3. Remove the stock retention clamps that hold the inner boot in place. Pull back boot and unscrew inner tie rod to remove. Fig.3-4PPE-158207000-Heavy-Duty-Forged-Tie-Rod-Assemblies- \(5\)

  4. Measure stock tie rod length from outer end centerline to inner end cap face. Loosen Jam Nut on PPE Tie Rod and adjust to match stock tie rod length. Tighten Jam Nut to 55 lb-ft. Fig.5-6
    Heavy-Duty Forged Tie Rod AssembliesPPE-158207000-Heavy-Duty-Forged-
Tie-Rod-Assemblies- \(6\)

  5. Before installing, detach the grease fitting from the inner tie rod if equipped. Reserve the use of the grease fitting exclusively for maintenance purposes. Fig.7PPE-158207000-Heavy-Duty-Forged-Tie-Rod-Assemblies- \(7\)

  6. Apply “red thread locker” to the threaded inner. Install and tighten to 75-85 lb-ft. Fig.8 Slide the boot over the inner tie rod and secure both clamps. Fig.9PPE-158207000-Heavy-Duty-Forged-Tie-Rod-Assemblies- \(8\)

  7. Install ball pin into steering knuckle. Tighten Lock Nut to 45 lb-ft. Fig.10PPE-158207000-Heavy-

  8. Repeat install procedure on passenger side.

  9. Have vehicle professionally aligned.
    This completes the installation PPE-158207000-Heavy-Duty-Forged-Tie-Rod-
Assemblies- \(10\)

DISCLAIMER OF LIABILITY

Performance products can increase horsepower above and beyond factory specifications. Additional horsepower creates more stress on the drive-train components, which could result in drive-train failure.
Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
This agreement sets forth the terms and conditions for the use of PPE products. The installation of this product indicates that the Buyer has read and understands this agreement and accepts the terms and conditions. PPE (Pacific Performance Engineering) Inc., its distributors, employees, and dealers (the “Seller”) shall not be responsible for the product’s proper use
and service. The buyer hereby waives all liability claims. The Buyer hereby acknowledges no reliance on the Seller’s skill or judgment to select or furnish goods suitable for any particular purpose and that there are no liabilities which extend beyond the description on the face hereof, and the Buyer hereby waives all remedies or liabilities expressed or implied, arising by law or otherwise (including without any obligation of the Seller with respect to fitness, merchantability and consequential damages), or whether or not occasioned by the Seller’s negligence.
The Seller disclaims any warranty and expressly disclaims any liability for personal injury or damages. The Buyer acknowledges and agrees that the disclaimer of any liability for personal injury is a material term for this agreement and the Buyer agrees to indemnify the Seller and to hold the Seller harmless from any claim related to the item of equipment purchased. Under no circumstances will the Seller be liable for any damages or expenses by reason of use or sale of any such equipment. The Seller assumes no liability regarding the improper installation or misapplication of its products. It is the installer’s responsibility to check for proper installation and if in doubt, contact the manufacturer. The Buyer is solely responsible for all warranty issues from the manufacturer.

LIMITATION OF WARRANTY

The Seller gives Limited Warranty as to description, quality, merchantability, and fitness for a particular purpose, productiveness, or any other matter of Seller’s product sold herewith. The Seller shall not be responsible for the products proper use and service and the Buyer hereby waives all rights other than those expressly written herein. This warranty shall not be extended, altered or varied except by a written instrument signed by Seller and Buyer.
Limited lifetime warranty on all PPE cast aluminum products, and PPE Transmission Coolers. Three (3) year limited warranty on PPE Manifolds and Up- Pipes Kits, and OEM-Length
Up-Pipes. One (1) year limited warranty on all other PPE products from the date of sale to original buyer and limited solely to the parts contained within the products kit. All products that are in question of Warranty must be returned prepaid to the Seller and must be accompanied by a dated proof of purchase receipt. All Warranty claims are subject to approval by Seller. Under no circumstances will the Seller be liable for any labor charged or travel time incurred in diagnosis for defects, removal, or re-installation – of this product or any other contingent expenses. Under no circumstances will the Seller be liable for any damage or expenses incurred by reason of the use or sale of any such equipment. In the event that the buyer does not agree with this agreement: the buyer may promptly return this product, in a new and unused condition in its original packaging, with a dated proof of purchase to the place of purchase within ten (10) days from date of purchase for a full refund. The installation of this product indicates that the buyer has read and understands this agreement and accepts its terms and conditions.
PPEpower.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

PPE User Manuals

Related Manuals