PPE 114053100 Heavy-Duty Deep-Capacity Cast Aluminum Engine Oil Pan Installation Guide
- June 8, 2024
- PPE
Table of Contents
PPE 114053100 Heavy-Duty Deep-Capacity Cast Aluminum Engine Oil Pan
INSTALLATION INSTRUCTION
- Step 1. Vehicle off. Engine cool. Completely drain the oil. Overnight, if possible.
- Step 2. Remove the skid plate, and crossmember, then unbolt and support the front differential. Lower and secure front differential for easier stock pan removal and installation of larger PPE pan.
- Step 3. Remove and retain stock bolts.
- Step 4. Locate the lower, passenger-side bell housing bolt. Remove the bolt and save. To make room for the larger pan, the bolt length will be trimmed in later steps.
- Step 5. Pry away the stock pan from the mating surface, using caution for the remaining oil. Remove the stock pan.
- Step 6. The thoroughly clean mating surface of all old silicone gasket material. Wipe the oil off the oil pickup.
- Step 7. Disconnect transmission coolant lines and secure, them up and out of the way, clearing enough room for installation. Tie off lines with a rag.
- Step 8. Apply silicone sealant to the pan mating surface and around bolt holes.
- Step 9. It is very important not to smear the sealant while installing the new pan. It is recommended you have help locating the dowel pin, which indexes the pan in the proper position. Starting from the rear, angle the pan over the differential as shown. Tip the back of the pan to level, being careful of the sealant. With a spotter’s help, lift the pan up into its indexed position, using the dowel as a reference. Once in position, install two factory bolts on each side (middle) to secure the pan. Finger-tighten bolts to hold the pan in position.
- Step 10. Install remaining bolts finger tight. Torque to 18-22 ft. lbs, starting from the center of the pan and working in a crossing pattern. (Fig. 1) Check the drain plug and NPT plug to be sure they’re tight.
- NOTE: Allow at least one hour for the silicone to set up.
- Step 11. Check and mark the bell housing bolts for trimming. (Fig. 2) Use a cut-off wheel to trim excess. Reinstall bolt and torque to manufacturer spec.
- Step 12. Reassemble front differential and torque to manufacturer spec. Reinstall transmission coolant lines, cross-member, and skid plates. Fill the engine with recommended oil. Start engine. Check for leaks. Top off transmission fluid if necessary.
DISCLAIMER OF LIABILITY
Performance products can increase horsepower above and beyond factory
specifications. Additional horsepower creates more stress on the drive-train
components, which could result in drive-train failure.
Note regarding emissions-related, non-E.O.-legal products: THESE PRODUCTS
ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER BE USED,
REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
This agreement sets forth the terms and conditions for the use of PPE
products. The installation of this product indicates that the Buyer has read
and understands this agreement and accepts the terms and conditions. PPE
(Pacific Performance Engineering) Inc., its distributors, employees, and
dealers (the “Seller”) shall not be responsible for the product’s proper use
and service. The buyer hereby waives all liability claims. The Buyer hereby
acknowledges no reliance on the Seller’s skill or judgment to select or
furnish goods suitable for any particular purpose and that there are no
liabilities which extend beyond the description on the face hereof, and the
Buyer hereby waives all remedies or liabilities expressed or implied, arising
by law or otherwise (including without any obligation of the Seller with
respect to fitness, merchantability and consequential damages), or whether or
not occasioned by the Seller’s negligence.
The Seller disclaims any warranty and expressly disclaims any liability for
personal injury or damages. The Buyer acknowledges and agrees that the
disclaimer of any liability for personal injury is a material term for this
agreement and the Buyer agrees to indemnify the Seller and to hold the Seller
harmless from any claim related to the item of equipment purchased. Under no
circumstances will the Seller be liable for any damages or expenses by reason
of use or sale of any such equipment. The Seller assumes no liability
regarding the improper installation or misapplication of its products. It is
the installer’s responsibility to check for proper installation and if in
doubt, contact the manufacturer. The Buyer is solely responsible for all
warranty issues from the manufacturer.
LIMITATION OF WARRANTY
The Seller gives Limited Warranty as to description, quality, merchantability,
and fitness for a particular purpose, productiveness, or any other matter of
Seller’s product sold herewith. The Seller shall not be responsible for the
product’s proper use and service and the Buyer hereby waives all rights other
than those expressly written herein. This warranty shall not be extended,
altered, or varied except by a written instrument signed by Seller and Buyer.
Limited lifetime warranty on all PPE cast aluminum products, and PPE
Transmission Coolers. Three (3) year limited warranty on PPE Manifolds and Up-
Pipes Kits and OEM-Length
Up-Pipes. One (1) year limited warranty on all other PPE products from the
date of sale to the original buyer and limited solely to the parts contained
within the products kit. All products that are in question of Warranty must be
returned prepaid to the Seller and must be accompanied by a dated proof of
purchase receipt. All Warranty claims are subject to approval by Seller. Under
no circumstances will the Seller be liable for any labor charged or travel
time incurred
in diagnosis for defects, removal, or re-installation – of this product or any
other contingent expenses. Under no circumstances will the Seller be liable
for any damage or expenses incurred by reason of the use or sale of any such
equipment. In the event that the buyer does not agree with this agreement: the
buyer may promptly return this product, in a new and unused condition in its
original packaging, with a dated proof of purchase to the place of purchase
within ten (10) days from date of purchase for a full refund. The installation
of this product indicates that the buyer has read and understands this
agreement and accepts its terms and conditions.
PPEpower.com
Documents / Resources
| PPE
114053100 Heavy-Duty Deep-Capacity Cast Aluminum Engine Oil
Pan
[pdf] Installation Guide
114053100, 114053120, 114053100 Heavy-Duty Deep-Capacity Cast Aluminum Engine
Oil Pan, 114053100, Heavy-Duty Deep-Capacity Cast Aluminum Engine Oil Pan,
Cast Aluminum Engine Oil Pan, Aluminum Engine Oil Pan, Engine Oil Pan, Oil
Pan, Pan
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>