PPE Stage5, Stage6 C5 Clutch Upgrade Kit Installation Guide
- June 8, 2024
- PPE
Table of Contents
PPE Stage5, Stage6 C5 Clutch Upgrade Kit
Stage5 / Stage6
C5 Clutch Upgrade Kit
Allison 1000, 2000, 2400
(128135105), (128035590)
Installation Guide
DISCLAIMER OF LIABILITY
Performance products can increase horsepower above and beyond factory
specifications.
Additional horsepower creates more stress on the drive-train components, which
could result in drive-train failure.
Note regarding emissions-related, non-E.O.-legal products:
THESE PRODUCTS ARE LEGAL IN CALIFORNIA ONLY FOR RACING VEHICLES THAT MAY NEVER
BE USED, OR REGISTERED OR LICENSED FOR HIGHWAY OR OFF-ROAD USE.
This agreement sets forth the terms and conditions for the use of PPE
products. The installation of this product indicates that the Buyer has read
and understands this agreement and accepts the terms and conditions. PPE
(Pacific Performance Engineering) Inc., its distributors, employees, and
dealers (the “Seller”) shall not be responsible for the product’s proper use
and service. The buyer hereby waives all liability claims. The Buyer hereby
acknowledges no reliance on the Seller’s skill or judgment to select or
furnish goods suitable for any particular purpose and that there are no
liabilities which extend beyond the description on the face hereof,
and the Buyer hereby waives all remedies or liabilities expressed or implied,
arising by law or otherwise (including without any obligation of the Seller
with respect to fitness, merchantability and consequential damages), or
whether or not occasioned by the Seller’s negligence.
The Seller disclaims any warranty and expressly disclaims any liability for
personal injury or damages. The Buyer acknowledges and agrees that the
disclaimer of any liability for personal injury is a material term for this
agreement and the Buyer agrees to indemnify the Seller and to hold the Seller
harmless from any claim related to the item of equipment purchased. Under no
circumstances will the Seller be liable for any damages or expenses by reason
of use or sale of any such equipment. The Seller assumes no liability
regarding the improper installation or misapplication of its products. It is
the installer’s responsibility to check for proper installation and if in
doubt, contact the manufacturer. The Buyer is solely responsible for all
warranty issues from the manufacturer.
LIMITATION OF WARRANTY
The Seller gives Limited Warranty as to description, quality, merchantability,
and fitness for a particular purpose, productiveness, or any other matter of
Seller’s product sold herewith.
The Seller shall not be responsible for the products proper use and service
and the Buyer hereby waives all rights other than those expressly written
herein.
This warranty shall not be extended, altered or varied except by a written
instrument signed by Seller and Buyer.
Limited lifetime warranty on all PPE cast aluminum products, and PPE
Transmission Coolers.
Three (3) year limited warranty on PPE Manifolds and Up-Pipes Kits, and OEM-
Length Up-Pipes.
One (1) year limited warranty on all other PPE products from the date of sale
to original buyer and limited solely to the parts contained within the
products kit.
All products that are in question of Warranty must be returned prepaid to the
Seller and must be accompanied by a dated proof of purchase receipt.
All Warranty claims are subject to approval by Seller.
Under no circumstances will the Seller be liable for any labor charged or
travel time incurred in diagnosis for defects, removal, or re-installation –
of this product or any other contingent expenses.
Under no circumstances will the Seller be liable for any damage or expenses
incurred by reason of the use or sale of any such equipment.
In the event that the buyer does not agree with this agreement: the buyer may
promptly return this product, in a new and unused condition in its original
packaging, with a dated proof of purchase to the place of purchase within ten
(10) days from date of purchase for a full refund.
The installation of this product indicates that the buyer has read and
understands this agreement and accepts its terms and conditions.
CONTENTS:
- 8 – (.071”) HEG Friction Plates
- 8 – (.078”) HEG Kolene Steel Plates
INSTALLATION INSTRUCTIONS
-
These stack up in the same order and the OE plates.
Install the pressure plate then a friction plate, followed by a steel plate and continue until the last plate is a steel plate. -
With a set of calipers, measure from the top of the lugs down to the top steel plate.
This clearance, which is not the actual clutch pack clearance, should be .170” to .200” (4.45 to 5.33mm). -
Finish by installing the OE return spring.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>