goobay 58884 Voltage Converter User Manual

User manual
Art.
58890 SPW IT 1000 (8099U1)
58884 SPW IT 1500 (8102U1) Voltage converter

**Safety instructions

**

1.1 General
The user manual is part of the product and contains important information for correct use.

• Read the user manual completely and carefully before use.
  The user manual must be available for uncertainties and passing the product.

• Keep this user manual.

Risk of electric shock

• Do not operate the device with wet hands!
• Attend to the maximum output currents of the product!
• Do not open the housing.
• Do not modify product and accessories.
• Do not short-circuit connectors and circuits.
• Do not insert objects into air vents or sockets!

A defective device may not be put into operation, but must be protected against further use.

• Use product, product parts and accessories only in perfect condition.
• In case of questions, defects, mechanical damage, trouble and other problems, non-recoverable by the documentation, contact your dealer or producer.
• Installation, assembly, maintenance and repair work must be carried out only by trained electrical specialists.

Not recommended for children and people with physical and / or mentally limited capabilities.

• Secure packaging, small parts and insulation against accidental use.
• Avoid stresses such as heat and cold, moisture and direct sunlight, microwaves, vibrations and mechanical pressure.
• Never let the product unattended when in use.
• Never operate irons, radiant heaters and similar devices that are a fire hazard via voltage transformers.
• DO NOT connect devices connected to the product via other interfaces on the vehicle at the same time.
• Use the product with running engine to avoid fast dicharging of the battery.
• Use the product only when the vehicle is parked.
• Disconnect the product from the vehicle battery before driving.
• The vehicle controls must not be affected by the installation and use of the product.

Explosion hazard

• Do not operate the product in an explosive environment.
• Do not use the product near flammable surfaces and substances and ex- plosive materials.

Hot surfaces

• Do not touch the housing during or immediately after use.
• Do not place any combustible materials (paper, cardboard, plastic, etc.) on the product.
• Do not cover cooling fins and fans.
• Do not use the product in sealed environments.

The unit heats up during operation.
1.2 Warning levels
WARNING
Warnings against hazards that may result in serious injuries or death in case of nonobservance.
NOTICE
Warnings against hazards that may result in material damage in case of non- observance.

Description and Function

2.1 Produkt
This product converts 12 V direct current to

• alternating current 230 V / 50 Hz and/or
• direct current 5 V / max. 2.1 A.

The voltage converter is intended for permanent installation in cars, trucks or boats and may only be operated in a stationary vehicle.
2.2 Scope of Delivery

• Voltage converter
• Battery cable black
• Battery cable red
• Grounding cable yellow/green with terminal connection
• User manual

2.3 Operating Elements

1. Fan
2. DC input (+)
3. Ground connection
4. DC input (-)
5. Power LED
6. Error LED| 7. AC output 230 V
8. DC Output USB 5 V
9. On/Off switch
10. Battery cable
11. Grounding cable
---|---

2.4 Specifications

Intended Use

We do not permit using the device in other ways like described in chapter „Description and Function“ or in the „Safety Instructions“. Use the product only in dry interior rooms. Not attending to these regulations and safety instructions might cause fatal accidents, injuries, and damages to persons and property.

Preparation

1. Check the scope of delivery for completeness and integrity.
2. Compare the specifications of all used devices and ensure compatibility.

Mounting and Connecting

5.1 Preparation

1. Check the battery terminals before connecting.
2. You must NOT use the voltage transformer with the vehicle if the positive pole „+“ is connected to a metallic part of the vehicle.
3. Use the battery cable with ring terminals for connecting to the vehicle battery.

The vehicle battery discharges when the vehicle is not in operation.
5.2 Mounting
Mount the voltage converter with suitable screws in the vehicle interior

• on stable and leveled places,
• on clean, dry and nonflammable surfaces,
• in well-ventilated areas.

Mounting screws are not included.
5.3 Connecting to the vehicle battery
WARNING
Ground short circuit and fire hazard

• DO NOT connect USB devices to the vehicle in parallel via another interface!
• Never place the voltage converter near flammable materials or in places where flammable gases can develop.
• Make sure that the voltage converter is switched off before you start connecting.
• Ensure that the polarity is correct.

1. Loosen the terminal screws of the plus and minus pole at the rear side of the voltage converter.

2. Put the red battery cable (10) straighht in the DC-input „+“ (2) and tighten the terminal screw.

3. Put the black battery cable (10) in the DC-input „-“ (4) and tighten the black terminal screw.

4. Connect the red battery cable (10) with the eyelet to the positive terminal of the battery.
   This is red or marked with „P“ or „+“.

5. Connect the black battery cable (10) with the eyelet to the negative pole of the battery.
   This is black or marked with „N“ or „-“.
   WARNING
   Risk of electric shock!
   Without an earth connection, there is a risk of electric shock in the event of equipment failure.

6. Connect the grounding cable (11) to the ground terminal (3) and to an available grounding system (e.g. the vehicle body; or to the potential output in case of stationary use).

Operation

6.1 In general
Some external devices such as audio and battery-powered devices and precision equipment may not be suitable to operate at a voltage converter and the connected device and/or the voltage converter may get damaged.

1. Check the user manual of the device to be connected to corresponding notices.
2. Turn the device off immediately and unplug the power cord when it hums or excessively heates up.
3. If there is anything unclear, contact the dealer of your device.

Both AC outputs 230 V (7) and the DC output USB 5 V (8) can be used simultaneously. The total power rating for all connected equipment must not exceed the continuous output of the voltage converter. The power rating of your equipment can be found on the nameplate. External devices, such as electric motors, drills, electric saws, refrigerators and music systems normally have a higher rated power when starting as indicated on the nameplate.
The voltage converter can therefore briefly make a higher peak output power if the power rating is only given in current as ampere,

• multiply the value in amperes (A) by a factor of 230 to to obtain the power in watts (W).

Example: 0.5 A x 230 V = 115 W
The vehicle battery discharges when the vehicle is not in operation.
6.2 Switching the voltage converter on/off

1. Turn the On/Off switch (9) on (ON).
   If the Operation LED (5) lights up, the voltage converter is ready for operation.

2. If the the Error LED (6) lights up, turn off the voltage converter by pressing the On/Off switch (OFF).

3. Read the chapter „Troubleshooting“.

6.3 Use of 230 V AC outputs
Use only devices that are equipped either with safety plug or european cable connectors.

1. Turn the voltage converter on (ON).
2. Make sure that the device to be connected is switched off.
3. Connect the plug of the device to be connected with the 230 V AC output (7) of the voltage converter.

6.4 Use of the 5 V USB DC output
NOTICE
Material damage
Do not connect memory sticks, MP3 player or similar external data storage devices.

1. Turn the voltage converter on (ON).
2. Connect a USB device to the USB 5 V DC connector (8).
   The DC Output USB 5 V of the voltage converter provides 5 V DC power for USB devices such as lights, fans and radios.
   The DC Output USB 5 V of the voltage converter does not support data transmission.

Fan

To save energy, the fan only works when

• the load is > 30% of the rated power of the voltage converter
• and/or the internal temperature of the voltage converter is > 60 °C.

Troubleshooting

to normal voltage, the alarm automatically stops.
Input low- voltage shutdown| green on red on| yes| no| • Charge the battery.
• Switch off the voltage converter for 3-5 seconds
• Switch the voltage con- verter on again.
Input over- voltage shutdown| green on red on| no| no| • Check the battery for correct voltage or re- store it.
• Switch off the voltage converter for 3-5 seconds.
• Switch the voltage con- verter on again.
Overload shutdown| green on red on| no| no| • Reduce the load to the specified continuous load.
• Switch off the voltage converter for 3-5 seconds.
• Switch the voltage con- verter on again.
Over temperature shutdown| green on red on| yes| no| • Eliminate the cause of overheating.
• Switch off voltage con- verter for ~5 minutes to cool down.
• Switch the voltage con- verter on again.
Output short circuit| green on red on| no| no| • Eliminate the cause of the short circuit.
The voltage transformer then continues to operate automatically.

Maintenance, Care, Storage and Transport

The product is maintenance-free.
NOTICE
Material damage

• Only use a dry and soft cloth for cleaning.
• Do not use detergents or chemicals.
• Store the product out the reach of children and in a dry and dust-protected ambience when not in use.
• Store cool and dry.
• Keep and use the original packaging for transport.
• Keep ventilation openings and cooling fins clean.

Liability notice

• We reserve the right to printing errors and changes to product, packaging or product documentation.
• See our terms of warranty. These are available in their current form under the given contact details.

Disposal instructions

11.1 Product
According to the European WEEE directive, electrical and electronic equipment must not be disposed with consumers waste. Its components must be recycled or disposed apart from each other. Otherwise contaminative and hazardous substances can damage the health and pollute the environment.
As a consumer, you are committed by law to dispose electrical and electronic devices to the producer, the dealer, or public collecting points at the end of the devices lifetime for free. Particulars are regulated in national right. The symbol on the product, in the user manual, or at the packaging alludes to these terms. With this kind of waste separation, application, and waste disposal of used devices you achieve an important share to environmental protection.
WEEE No: 82898622

11.2 Packaging
Packaging can be disposed of free of charge at the suitable collection points – paper belongs in paper bins, plastics belong in yellow sacks and glass belongs in used glass bins.
DE4535302615620

EU Declaration of conformity

With the CE sign Goobay®, a registered trademark of the Wentronic GmbH ensures, that the product is conformed to the basic European standards and directives.

ECE sign

With the ECE sign Goobay®, a registered trademark of the Wentronic GmbH, ensures, that the required tests and approvals have been carried out and an ECE aproval has been granted.
10R-06 15531
10R-06 15531

Symbols used

For indoor use only| IEC 60417- 5957|
---|---|---
Alternating current| IEC 60417- 5032|
Direct current| IEC 60417- 5031|
Recycling| ISO 7001 – PI PF 066|

REV2024-06-14
V2.1ir
Goobay®
by Wentronic GmbH
Pillmannstraße 12
38112 Braunschweig
Germany
Made in China
© by Wentronic Deutschland
Hotline: +49 (0180) 5005882
E-Mail:info@goobay.de
Web: www.wentronic.com/content/mygoobay/
(0.14 € / minute from German landline)
Voltage converter

Documents / Resources

| goobay 58884 Voltage Converter [pdf] User Manual
58884 Voltage Converter, 58884, Voltage Converter, Converter
---|---

References

• Goobay – Wentronic

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>