RADIOSHACK 3304409 Wireless Headphone User Manual
- June 26, 2024
- RadioShack
Table of Contents
RADIOSHACK 3304409 Wireless Headphone
Product Information
Specifications:
- Brand : RADIOSHACK WORLDWIDE CORP.
- Model : 3304409
- Package Contents: Headset, Type-C charging cable, User Guide
- Volume control wheel, MODE button, On/Off Button, Audio port, Type-C charging port
Product Usage Instructions
Charging:
- Connect the Type-C charging cable to the headphone and a USB source.
- LED lights red when charging and turns off when fully charged.
2.4GHz Connection:
- When the headset is turned on, the default connection is on 2.4GHz mode.
- Insert 2.4GHz dongle to your device. The headset will be automatically detected.
Bluetooth Connection:
- Press and hold the MODE button to switch to Bluetooth mode.
- On your device, turn on the Bluetooth function, and set it to search for Bluetooth devices.
- Select (GT02) from the list of found devices.
- When paired, the LED flashes blue slowly.
Built-in Equalizer:
The headset comes with 4 built-in EQ presets. Each preset will be indicated by
a beep sound. Toggle the EQ accordingly:
- One beep sound: EQ1-Default EQ
- Two beep sounds: EQ2-Soft Bass
- Three beep sounds: EQ3-Deep Bass
- Four beep sounds: EQ4-Vocal Boost
Volume Adjustment:
The volume can be adjusted using the volume control wheel by sliding up or
down.
Microphone:
The microphone is attached to the left earpiece. Pull the top down to activate
the microphone and flip it back up to store and mute.
Package
- Headset
- Type-C charging cable
- User Guide
Specification
- Input charging voltage: 5V, 500mA
- Charging port: Type-C
- Charge time : approx. 3hours
- Playing time : up to 20 hours,
- Battery capacity: 3.7V, 500 mAH
- Bluetooth version: V5.4
- Frequency response: 20Hz-20kHz (Speaker)
- Sensitivity: 100±3dB(Speaker)
- Bluetooth connection range: approx. 10m
Specifications are subject to change and improvement without notice. Actual product may vary from the images found in this document
Note : During pairing, if the headphones are not connected to a device within 5 minutes, they automatically turn off.
NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
FAQ
Q: What should I do if the headphones are not connected to a device within
5 minutes?
A: The headphones will automatically turn off. Reconnect by following the
pairing instructions.
Q: How can I improve connectivity if I experience interference?
A: Try reorienting or relocating the receiving antenna, increasing separation
between equipment and receiver, or consulting a professional technician for
assistance.