Atlas Copco MWR-KIT Mechatronic Wrench Instruction Manual
- June 12, 2024
- Atlas Copco
Table of Contents
MWR-KIT Mechatronic Wrench
Instruction Manual Printed Matter No. 9839 1723 00
Publication Date 2023-02-15
Valid from Serial No. B4780167
MWR-KIT
4027502206
MWR-KIT Mechatronic Wrench
WARNING
To reduce risk of injury, everyone using, installing, repairing, maintaining,
changing accessories on, or working near this tool MUST read and understand
these instructions before performing any such task.
DO NOT DISCARD – GIVE TO USER
Safety Information
Declarations
EU DECLARATION OF CONFORMITY
We, Atlas Copco Industrial Technique AB, SE-105 23
STOCKHOLM SWEDEN, declare under our sole responsibility that the product (with
name, type and serial number, see front page) is in conformity with the
following Directive(s): 2011/65/EU (RoHS), 2014/53/EU (RED), 2015/863/EU (RoHS
amendment)
Harmonized standards applied:
EN 300220-1 v3.1.1, EN 300220-2 v3.2.1, EN 301489-1
v2.2.3, EN 301489-3 v2.1.1, EN 50581:2012, EN
55032:2015 + AC:2016 + A11:2020 + A1:2020, EN
55035:2017 + A11:2020, EN 61000-3-2:2019 + A1:2021,
EN 61000-3-3:2013 + A1:2019 + A2:2021, EN 61010-1, EN 62311:2008
Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Technique AB, SE-105 23
Stockholm Sweden
Stockholm, 1 November 2022
Lars Eklöf, Managing Director
Signature of issuer
WEEE
Information concerning Waste of Electrical and Electronic Equipment (WEEE):
This product and its information, meets the requirements of the WEEE
directive/regulations (2012/19/EU), and must be handled in compliance with the
directive/regulations.
The product is marked with the following symbol:
Products marked with a crossed-out wheeled bin symbol and a single black bar
underneath, contain parts that must be handled in compliance with the WEEE
directive/regulations.
The entire product, or the WEEE parts, can be sent to your “Customer Center”
for handling.
RF Exposure Statement
This portable transmitter has been tested and found to comply with FCC General
Population RF Radiation Exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines. The
antenna used for this device must not be co-located or operating in
conjunction with any other antenna or transmitter.
Radio interference
This is a class A product. In a domestic environment this product may cause
radio interference.
Information regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registration, Evaluation,
Authorization and restriction of Chemicals (REACH) defines among other things
requirements related to communication in the supply chain. The information
requirement applies also to products containing so called Substances of Very
High Concern (the “Candidate List”). On 27 June 2018 lead metal (CAS nr
7439-92-1) was added to the Candidate List.
In accordance with the above this is to inform you that certain electrical
components in the product may contain lead metal. This is in compliance with
current substance restriction legislation and based on legit exemptions in the
RoHS Directive (2011/65/EU). Lead metal will not leak or mutate from the
product during normal use and the concentration of lead metal in the complete
product is well below the applicable threshold limit. Please consider local
requirements on the disposal of lead at product end of life.
FCC and ISED Compliance Statement
This device complies with Part 15 of the FCC Rules. Any changes or
modifications not expressly approved by the manufacturer could void the user´s
authority to operate this device.
Operation is subject to the following two conditions:(1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
The device is only in compliance if no changes or modifications are made to
the device.
The device is in compliance with the requirement for RF exposure in the US
with a 5 mm separation distance between the user and the device – Atlas Copco
recommends a separation distance of 20 cm between the user and the device.
The antenna is fixed to the device and no change in antenna or fixation of the
antenna is acceptable and such modification is considered to violate the
Compliance Statement.
FCC Responsible party:
Name: Rodney Hill
Position: Product Marketing Manager
Address: 3301 Cross Creek Parkway
MI 483 26 Auburn Hills
United States
Mobile: +1 919 272 7837
Email: rodney.hill@us.atlascopco.com
FCC ID: 2AIPFMWRKIT
** This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
ISED Compliance Statement:**
This device complies with: CAN ICES-1(A)/NMB-1(A)
This device complies with Industry Canada’s licence-exempt RSSs. Operation is
subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
Company Name: Woodstar Inc
Contact Name: Stephane Mercure
Street Address: 46 chemin du Faisan, Saint Sauveur, Quebec, Canada, J0R R1R
Telephone No: 514-667-6868
Fax No: 514-6676870
Email: ms@woodstar.ca
IC_ID: 21556-MWRKIT
This radio transmitter 21556-MWRKIT has been approved by Innovation, Science
and Economic Development Canada to operate with the antenna types listed
below, with the maximum permissible gain indicated.
Antenna types not included in this list that have a gain greater than the
maximum gain indicated for any type listed are strictly prohibited for use
with this device.
Antenna type | Antenna model | Maximum antenna gain [dBi] | Impedance [Ω] |
---|---|---|---|
λ/4 whip | DELTA 12 | 3 | 50 |
Vertical stilus | AS868 | 3 | 50 |
Quarter wave ground plane | GP868 | 3 | 50 |
** This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Industry Canada’s license-exempt RSSs.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Regional Requirements
WARNING
This product can expose you to chemicals including lead, which is known to the
State of California to cause cancer and birth defects or other reproductive
harm. For more information go to https://www.p65warnings.ca.gov/
UK DECLARATION OF CONFORMITY**
We, Atlas Copco Industrial Technique AB, SE-105 23 STOCKHOLM SWEDEN, declare
under our sole responsibility that the product (with name, type and serial
number, see front page) is in conformity with the following UK Regulation(s):
S.I. 2017/1206
Designated Standards applied:
BS EN 300220-1 v3.1.1, BS EN 300220-2
v3.2.1, BS EN 301489-1 v2.2.3, BS EN
301489-3 v2.1.1, BS EN 50581:2012, BS EN
55032:2015 + AC:2016 + A11:2020 + A1:2020,
BS EN 55035:2017 + A11:2020, BS EN
61000-3-2:2019 + A1:2021, BS EN
61000-3-3:2013 + A1:2019 + A2:2021, BS EN
61010-1, BS EN 62311:2008
Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Technique AB, SE-105 23
Stockholm
Sweden
Stockholm, 1 November 2022
Lars Eklöf, Managing Director
Signature of issuer
Authorised Representative UK
James McAllister, General Manager
Atlas Copco Ltd
Swallowdale Lane
Hemel Hempstead
Hertfordshire HP2 7EA
Safety
DO NOT DISCARD – GIVE TO USER
WARNING Read all safety warnings, instructions, il- lustrations and
specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock,
fire, and/or serious injury.
Save all warnings and instructions for future reference.
WARNING All locally legislated safety rules regarding installation,
operation and maintenance shall be respected at all times.
Statement of Use
- For professional use only.
- This product and its accessories must not be modified in any way.
- Do not use this product if it has been damaged.
- If the product data or hazard warning signs on the product cease to be legible or become detached, replace without delay.
- The product must only be installed, operated and serviced by qualified personnel in an industrial environment.
Intended Use
This product is designed to enable wireless communication between the Power
Focus 6000 and the Mechatronic Wrench (MWR). Indoor use only. No other use
permitted.
Electrical Safety
WARNING This apparatus must be earthed.
- Earthed equipment must be plugged into a socket that has been properly installed and earthed according to appropriate regulations. Never remove the earth pin or modify the plug in any way. Do not use any adapter plugs. Check with a qualified electrician if you are in any doubt as to whether the outlet is properly earthed. Should the equipment suffer electronic malfunction or breakdown, the earth provides a low resistance path to carry electricity away from the user. Applicable only to Class I (earthed) equipment.
- Disconnect from the power supply before servicing.
- Failure to comply with these operating instructions may impair the safety of this equipment.
- Failure to follow these instructions may result in electric shock.
- Must not be used in explosive atmospheres.
- Avoid physical contact with grounded surfaces such as pipes, radiators, ovens and refrigerators. There is an increased risk of electric shock if your body is grounded.
- Do not expose the equipment to rain or wet conditions. Water entering the equipment will increase the risk of electric shock. This instruction does not apply to equipment classified as watertight or splash proof.
- For minimum electrical interference, locate the equipment as far as possible from sources of electrical noise, e.g. arc welding equipment etc.
Signs and Stickers
The product is fitted with signs and stickers containing important information
about personal safety and product maintenance. The signs and stickers shall
always be easy to read.
New signs and stickers can be ordered by using the spare parts list.
WARNING
Useful Information
ServAid
ServAid is a portal that is continuously updated and contains Technical
Information, such as:
- Regulatory and Safety Information
- Technical Data
- Installation, Operation and Service Instructions
- Spare Parts Lists
- Accessories
- Dimensional Drawings
Please visit: https://servaid.atlascopco.com.
For further Technical Information, please contact your local Atlas Copco
representative.
© Copyright 2023, Atlas Copco Industrial Technique AB. All rights reserved.
Any unauthorized use or copying of the contents or part thereof is prohibited.
This applies in particular to trademarks, model denominations, part numbers
and drawings. Use only authorized parts. Any damage or malfunction caused by
the use of unauthorized parts is not covered by Warranty or Product Liability.
Out of respect to wildlife and nature, our technical literature is printed on
environmentally friendly paper.
Atlas Copco Industrial
Technique AB
SE-10523 STOCKHOLM
Sweden
Telephone: +46 8 743 95 00
www.atlascopco.com
References
- Atlas Copco | Home of Industrial Ideas
- Atlas Copco | Home of Industrial Ideas
- ServAid - Spare Parts and Product Information - ServAid
- p65warnings.ca.gov/
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>