DENSO TEN TN0036A Car Audio User Manual

June 22, 2024
DENSO TEN

DENSO TEN TN0036A Car Audio

DENSO-TEN-TN0036A-Car-Audio-PRODUCT

Specifications

  • RATED VOLTAGE: 12V (10.5-16.0V)
  • LOAD IMPEDANCE: – ground 4
  • BACK UP CURRENT: 2.1mA or less
  • RATED CURRENT: 4.0 or less (Vcc=13.2V, 0.5W output)
  • AM TUNING RANGE: 531 – 1602 kHz (9kHz step)
  • FM TUNING RANGE: 87.5 – 108 MHz (50kHz step)

Product Usage Instructions

Radio Operation Procedure

Upon turning the vehicle’s ACC-ON, follow these steps:

  1. Confirm Toyota screen display.
  2. Press the Continue button to access the MENU screen.
  3. To switch to FM1 mode, press the POWER button.
  4. To seek stations, press the SEEK button.

Operating Manual (Bluetooth/Handsfree)

For Bluetooth connectivity:

  1. After ACC-ON, ensure the Toyota screen is displayed.
  2. Press “Add Device” to initiate device pairing.
  3. Follow on-screen instructions to complete pairing with iPhone or iPod.
  4. Connection Completed message confirms successful pairing.

Operating Manual (Wi-Fi/Carplay)

For Wi-Fi/Carplay usage:

  1. Upon ACC-ON, verify Toyota screen display.
  2. Press “Search” button to start searching for iPhone with Bluetooth ON.
  3. Enable Bluetooth on the iPhone to establish connection.

FAQ

Q: How do I adjust the volume on the car audio system?

A: Use the VOL UP and VOL DOWN buttons for incremental volume adjustments. Long presses will adjust volume continuously.

Q: What should I do if the screen does not change after ACC-ON?

A: Wait a few moments as it may take some time, especially during initial setup. If the issue persists, consult the troubleshooting section of the manual.

Model name Car Audio
Model No TN0036A

1-Rating

RATED VOLTAGE 12V (10.5~16.0V) – ground
LOAD IMPEDANCE
BACK UP CURRENT 2.1mA or less
RATED CURRENT 4.0A or less

(Vcc=13.2V, 0.5W output)

AM TUNING RANGE| 531 – 1602 kHz (9kHz step)
FM TUNING RANGE| 87.5 – 108 MHz (50kHz step)
DAB TUNING RANGE| 174.928 – 229.072 MHz

Button Function Spec

DENSO-TEN-TN0036A-Car-Audio-FIG-25

AUDIO controls

■AUDIO controls

Button No.| Button Name| Operation
| VOL DOWN| Short Push: Decrease Volume Down 1 step Long Push: Decrease Volume Down continuously
| VOL UP| Short Push: Increase Volume Up 1 step Long Push: Increase Volume Up continuously
| HOME/TALK| Short Push: Transition to home screen Long Push: AA/CP voice recognition
| BACK| Transition to previous screen
| POWER| Audio ON/OFF

Radio operation procedure

Operation procedure
  1. (ACC-ON)
    After the ACC-ON, confirm that Toyota screen is displayed.

  2. The screen is changed to “CAUTION” screen after a few seconds.
    Note: It takes a little longer for the first time of ACC-ON.DENSO-TEN-
TN0036A-Car-Audio-FIG-2

  3. Press the “Continue” button on the face panel after a few seconds to move MENU screen.DENSO-TEN-TN0036A-Car-Audio-FIG-3

  4. Press the POWER button.
    When the Radio Mode Window on the screen is pressed,”FM1″ screen is displayed .DENSO-TEN-TN0036A-Car-Audio-FIG-4

  5. Confirm that the screen is changed as below, Please push down the ”<”button or ”>”button.
    This will start to SEEK.DENSO-TEN-TN0036A-Car-Audio-
FIG-5
    Same as AM/DAB mode.

Operating manual (Bluetooth/Handsfree)

  1. (ACC-ON)
    After the ACC-ON, confirm that Toyota screen is displayed.DENSO-TEN-TN0036A-
Car-Audio-FIG-6

  2. The screen is changed to “CAUTION” screen after a few seconds.
    Note: It takes a little longer for the first time of ACC-ON.DENSO-TEN-
TN0036A-Car-Audio-FIG-7

  3. Press the “Continue” button on the face panel after a few seconds to move MENU screen.DENSO-TEN-TN0036A-Car-Audio-FIG-8

  4. Please press the “Setting” button on the face panel to move to Settings screenDENSO-TEN-TN0036A-Car-Audio-FIG-9

  5. Confirm if ”Settings” screen is displayed, select the ”Bluetooth” button on the display.DENSO-TEN-TN0036A-Car-Audio-FIG-10

  6. Please press the ”Add Device” button of the screenDENSO-TEN-TN0036A-Car-Audio-FIG-11

  7. Please press the ”Search Device” button of the screenDENSO-TEN-TN0036A-Car-Audio-FIG-12

  8. Confirm if screen is changed as below,
    Please set iPhone or iPod in pairing mode.DENSO-TEN-TN0036A-Car-Audio-
FIG-13
    Displays when you have more than one pairing equipment

  9. Select the iPhone or iPod to connect.DENSO-TEN-TN0036A-Car-Audio-FIG-14
    Operate the phone after the message on the screen

  10. ”Connection Completed” is displayed if completed.DENSO-TEN-TN0036A-Car-Audio-FIG-15

Operating manual (Wi-Fi/Carplay)

  1. (ACC-ON)
    After the ACC-ON, confirm that Toyota screen is displayed.DENSO-TEN-TN0036A-
Car-Audio-FIG-16

  2. The screen is changed to “CAUTION” screen after a few seconds.  Note: It takes a little longer for the first time of ACC-ON.DENSO-TEN-TN0036A-Car-Audio-FIG-17

  3. Press the “Continue” button on the face panel after a few seconds to move MENU screen.DENSO-TEN-TN0036A-Car-Audio-FIG-18

  4. Please press the “Setting” button on the face panel to move to Settings screen

  5. Confirm that the screen will change to the “Settings” screen, slide it down and select the “Seach Apple CarPlay Device” button on the screen.

  6. Please press the ”Search” button of the screen At this time, turn on Bluetooth on the iPhone to be connected.DENSO-TEN-TN0036A-Car-Audio-FIG-21

  7. Please Select the connected iPhone.

  8. If the display looks like the one below, press the [OK] button on the product side and press [Pairing] on the iPhone sideDENSO-TEN-TN0036A-Car-Audio-FIG-23

  9. Connection is completed when the screen automatically transitions to the CarPlay screen.DENSO-TEN-TN0036A-Car-Audio-FIG-24

FCC Operating manual Requirement

  • Co-location: This transmitter must not be co-located or operated in conjunction with anyother antenna or transmitter. This device complies with part 15 of the FCC Rules. Operation is subject to the followingtwo conditions: (1) This device may not cause harmful interference, and (2) this device mustaccept any interference received, including interference that may cause undesired operation. FCC WARNING Changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.CAUTION: Radio Frequency Radiation ExposureThis equipment complies with FCC radiation exposure limits set forth for uncontrolledequipment and meets the FCC radio frequency (RF) Exposure Guidelines.
  • This equipmentshould be installed and operated keeping the radiator at least 20cm or more away fromperson’s body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals