KENWOOD KCA-M100BT Bluetooth Controller Instruction Manual

KCA-M100BT Bluetooth Controller

Specifications

• Bluetooth® Profile A2DP (High-Quality, Stereo Audio)
• Bluetooth® Core Specification Version 5.0 with aptX®
• Water Resistance Rating IP66
• Frequency Response 20 Hz — 18 kHz (+/- 1dB)
• Outputs Front, Rear, & Subwoofer
• Output Voltage 2V RMS
• Signal to Noise Ratio 93 dB (20 Hz — 20 kHz)
• Input Operating Voltage 9 — 16 VDC
• Current Draw 48 mA (at idle); 64 mA (at full output)
• Operational Temperature Range -10° C — +60° C
• Remote Turn-on Output Capacity 350 mA (max)
• Fuse Rating 2A Mini ATC
• Connection Range (Maximum range is acheived in line-of-sight installations, actual range varies based on installation specifics) Up to 35 ft / 11 m

Product Usage Instructions

KCA-M100BT Contents & Controller Functions
The controller functions include Power ON/OFF, Play/Pause, Volume Up, Volume Down, Track Forward, Track Back, Subwoofer Level Up, Subwoofer Level Down, Bluetooth Pairing Mode, and RGB Illumination Color Adjust.

KCA-M100BT Installation Instructions
Wiring Diagram:

• Black : -12V Ground
• Blue : Amplifier Remote Turn On (+12V Output)
• Red : +12V Switched (Accessory)
• Yellow : +12V Battery (Constant Power)
• Front (Gray), Rear (White), & Subwoofer (Black) Preouts (Left; White, Right; Red)

Mounting Instructions:
The KCA-M100BT uses a threaded-collar mounting system for installation on surfaces up to 1.75 inches in thickness.

KCA-M100BT Pairing Instructions & Specifications
How to Pair Phone/Bluetooth Device:

1. Follow the pairing instructions in the manual.
2. To connect a second device for 2-phone music streaming, pause playback on the first device and start playback on the second device.

Accessories

• The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by JVCKENWOOD Corporation is under license. Other trademarks and trade names are those of their respective owners.
• Qualcomm aptX is a product of Qualcomm Technologies International, Ltd. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries, used with permission. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries, used with permission.

Take the time to read through this instruction manual. Familiarity with installation and operation procedures will help you obtain the best performance from your new product.

Controller Functions

Installation – Wiring Diagram

NOTE : After wiring, be sure to insulate and waterproof connections.

Mounting Instructions

Installation – Mounting
The KCA-M100BT uses a single hole for installation. It features a threaded- collar mounting system that enables installations in flat surfaces up to 1.75 inches (4.5 cm) in thickness. Please refer to the diagram below:

Standard Collar-Mount Installation

Pairing Instructions & Specifications

How to Pair Phone / Bluetooth Device

1. Make sure Bluetooth is turned ON in the settings of the phone/Bluetooth device.
2. Press and hold the settings button for 3 seconds. The RGB lights will flash, letting you know that the Bluetooth from the KCA-M100BT is ready to pair with your device.
3. From your Bluetooth device, search for available connections and select the KCAM100BT. At this point, the device should be connected, however, some devices may ask you to select the Bluetooth connection type. If so, select the option to connect to A2DP music but not to the hands-free profile connection (HFP). Alternatively, Some devices may have a setting in which you can disable “Phone calls” and just enable “Media audio”.
4. Select a music playback source on your device to begin music playback and then the play/pause and track buttons will be active on the controller.

2-Phone Music Streaming – Connecting a Second Device

1. After 1st phone is already connected use the same procedure as indicated above in setps 1-3.
2. Pause the active music playback on the first device (or from the controller), then select a music playback source on your second device and press play to begin its music playback.

Important Notes

FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio / TV technician for help.

Supplier’s Declaration of Conformity

• Trade Name: KENWOOD
• Products: BLUETOOTH CONTROLLER
• Model Name: KCA-M100BT
• Responsible Party: JVCKENWOOD USA CORPORATION 4001 Worsham Avenue, Long Beach, CA 90808, U.S.A.
• PHONE : 1-800-252-5722

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

1. THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND
2. THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

ISED Caution
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic

Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAUTION
This equipment complies with FCC/ISED radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the ISED radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20 cm or more away from the person’s body.

For updated information (the latest Instruction Manual, etc.),
please visit the following website: https://manual.kenwood.com/en_contents/search/

SCAN THE CODE

FAQs

Q: What should I do if I encounter interference with the device?
A: If you experience interference, try repositioning the device for better signal reception. Ensure there are no obstructions between the connected devices.

Q: Can I use the KCA-M100BT in extremely humid conditions?
A: The KCA-M100BT has an IP66 water resistance rating, making it suitable for use in humid conditions, but it should not besubmerged in water.

References

• Manual Download | Kenwood

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>