Newell 2.4G Wireless Remote Control Instruction Manual
- June 14, 2024
- Newell
Table of Contents
Newell 2.4G Wireless Remote Control
DESCRIPTION
SELECT THE CHANNEL ON THE REMOTE & PAIR THE REMOTE WITH TH ELED LIGHT
-
Before using the remote control, make sure that the AAA 1.5v x2 batteries are correctly placed in the compartment.
-
Switch on the LED light. Make sure the light is on when you are ready to pair them.
Note: Pressing the ON/OFF button on the remote control will not turn the light on or off before pairing. -
A short press of the ON/OFF button will activate the remote control if the LCD screen is in standby mode.
-
To pair the lamp and the remote control, the channels on both devices must be the same.
-
If the channel on the lamp is different from that on the remote control, pairing will fail. Re-select the channel on the remote control by pressing the
button. -
Go to the channel selection screen by pressing the
button. -
Select a channel on the remote control by pressing the<+>< – > button.
-
Press the
button again to confirm the selected channel and return to the menu. -
Check that the remote control is synchronised with the lamp.
-
You can now use the remote control to control the lamp.
-
The LCD screen will automatically go into standby mode if the remote control is not used for a few seconds. Press the ON/OFF button to activate the LCD screen on the remote control.
-
If channel 00 is selected, all lamps on channels 01-99 will be controlled.You can then control the brightness, colour temperature, RGB mode and power on/off with the remote control.
SWITCHING THE LED LAMP ON AND OFF USING THE REMOTE CONTROL
-
When the lamp is on, you can press the ON/OFF button to activate or deactivate it.
If you want to use the remote control to control it, make sure that the light is always on.
Note: if the lamp is off, the remote control will not interact with it when the ON/OFF button is pressed. -
A short press of the ON/OFF button activates the LCD screen on the remote control.
-
Make sure the remote control and the lamp are paired to the same channel.
-
A long press of the ON/OFF button for 2-3 seconds will switch the lamp to sleep mode.
-
Pressing the ON/OFF button twice will activate the unit from sleep mode.
-
If the LCD screen of the remote control goes into standby mode, press the ON/OFF button once to activate it again.
TRYBCCT
- Shortly press ON/OFF button once to activate the remote.
- Shortly press MODE button and go to CCT mode as the screen above.
- Press CH button to select the channel by< – ><+>,shortly press CH button again to confirm and go back to CCT mode as the screen above.
- Press<-><+> to adjust the color temperature from 3200K to 5600K, each step is 100K.
- Press< .a.> < ‘f’ > to move to brightness, increase or decrease the light intensity by < – > < + > from 10% to 100%, each step is 1%.
RGB MODE
- Shortly press ON/OFF button once to activate the remote.
- Shortly press MODE button and go to RGB mode as the screen above
- Press CH button to select the channel by< – ><+>,shortly press CH button again to confirm and go back to RGB mode as the screen above.
- Press<-><+> to adjust the RGB color from the value 1 to 360, each step is 1.
- Press< .a.> < ‘f’ > to move to brightness, increase or decrease the light intensity by < – > < + > from 10% to 100%, each step is 1%
- Press< ..a..> < T > to move to the saturation, increase or decrease the color saturation by < – > < + > from 10% to 100%, each step is 1%.
Important Notice : The RGB mode is not applicable on the light models which have not RGB features.
EFFECTS MODE
- Briefly press the ON/OFF button to activate the remote control.
- Briefly press the START button to enter special effects mode.
- Press the CH button and enter the channel mode. Select the desired channel by pressing < – > < + >, confirm and return by briefly pressing the CH button again.
- Press the< .. > < .. > buttons to move up and down the menu. Press < – ><+>to select the desired special effect.
- Press < .. > <-.> to move to glow, then press< – ><+>to change the intensity of the brightness from 10% to 100%. Each step up or down is 1%. Operation on the remote control will be synchronised with the device from the first value setting after pairing.
- Press < .. > <-.> to move to the special effects frequency, and then press < – ><+>to adjust the frequency from 1 to 9. The higher the value, the higher the flashing frequency. The action on the remote control will be synchronised to the unit from the moment the first value is set after pairing.
SPECIFICATION
| Battery type ( AAA X 2) | not included |
|---|---|
| Wireless frequency | 2,4 GHz |
| Max. remote distance | ;,: 50 M (16,4 FT) |
| Channels | 99 |
| Size | 44 mm x 138 mm x 23 mm |
| Weight | 68 g |
| Working temperature | -10N50°C |
WASTE MANAGEMENT
The crossed-out trashcan symbol means that waste electrical and electronic equipment, batteries and packagings must not be placed with other household waste. They must be handed over to a separate waste collection system.
WARRANTY
Newell products are covered by a 40-month manufacturer’s warranty .
- The manufacturer reserves the right to change the information contained in this manual without prior notice.
Made In China, In China hergestellt, Hecho en Chine, Febbricato In Cine, Fabrique en Chine, Vyrobeno v Crne, Wyprodukowano w Chinach, CAenaHo B Kl1Tile.
AKCESORIA FOTOGRAFICZNE
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>