TREK 25mm DuoTrap Digital Speed Cadence Sensor Instruction Manual

TREK 25mm DuoTrap Digital Speed Cadence Sensor

Product Information

Specifications

• Product Name: DuoTrap Sensor
• Battery Type: CR2032
• Battery Life: Approximately 200 hours
• Wireless Connectivity: Ant+ and Bluetooth Smart
• LED Indicators: Yes
• Compatibility: Works with most cycling apps and devices

Product Usage Instructions

• Open the battery compartment.
• Install the CR2032 battery using a coin to tighten it securely.
• Remove the DuoTrap cover from the chainstay using a 2.5mm hex key.
• Install the sensor into the chainstay and tighten the bolt to 2Nm.
• Install the rubber plug.
• Snap the speed magnet onto the inside/trailing edge non-drive side spoke.
• Center align the speed magnet with the marking on the sensor.
• Install the cadence magnet on the non-drive side crank arm or align the cadence band with the marking on the sensor.

FAQ

• Q: How long will the sensor stay active after activation?
• A: The sensor will remain active for at least 2 minutes after initial activation, even if the LEDs stop flashing.
• Q: What type of batteries can be used with the DuoTrap Sensor?
• A: The DuoTrap Sensor is compatible with CR2032 batteries, whether alkaline, carbon-zinc, or rechargeable.

Please refer to the manual for detailed troubleshooting and additional information.

For more information, visit www.bontrager.com

What In The Box

Installation Instructions

1. Open the Battery compartment.
2. Install the battery using a coin to tighten it.
3. Remove the DuoTrap cover from the chainstay using a 2.5mm hex.
4. Install the sensor into the chainstay.
5. Tighten the bolt to 2Nm and install the rubber plug.
6. Snap magnet onto inside/trailing edge non-drive side spoke. Some carbon frame/wheel combinations may require the magnet to be flipped so the thin side faces the sensor.
7. Center align speed magnet with either marking on sensor as depicted.
8. Gently tighten the wheel magnet on the spoke only if slipping during riding.
9. Install a cadence magnet on the non-drive side crank arm with the logo facing out. The pedal will need to be removed for this step.
10. Center align cadence band with either marking on the sensor as depicted.
11. LED indicators will flash upon activation by two complete pedal strokes and continue to flash 10 times.

PAIRING AND SENSOR ACTIVATION

• Pairing: Consult your Ant + or Bluetooth Smart device’s instructions for pairing. The sensor will need to be activated directly before the pairing process.
• Sensor Activation: To verify proper magnet installation, spin a wheel or turn the crank more than two revolutions. Initial sensor activation and magnet alignment will be indicated by the LEDs flashing up to 10 times.
• Please Note: The sensor will stay active for at least 2 minutes although the LEDs no longer flash.
• Bluetooth Smart Connection: Install and activate the sensor. Turn on your phone’s (or other compatible device)
• Bluetooth capability. Open the desired cycling app and follow the instructions for Bluetooth Smart sensor connection.
• Please note, that Bluetooth Smart devices do not always appear in your phone’s listing, even when connected.
• All apps collect, share, and display speed and cadence information differently.

FCC STATEMENT

FCC ID: 04GDTRAP
This device complies with part 15 of the FCC Rules.
Operation is subject to the following conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

NOTES
THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE GRANTEE OF THIS DEVICE COULD VOID THE USER’S AUTHORITY TO OPERATE THE DEVICE.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio / TV technician for help.

WARNING!

• INGESTION HAZARD: This product contains a button cell or coin battery.

• DEATH or serious injury can occur if ingested.

• A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.

• KEEP new and used batteries OUT OF REACH OF CHILDREN.

• Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body. Remove and immediately recycle or dispose of used batteries according to local regulations and keep them away from children. Do NOT dispose of batteries in household trash or incinerate them.

• Even used batteries may cause severe injury or death.

• Call a local poison control center for treatment information.

• Non-rechargeable batteries are not to be recharged.

• Do not force discharge, recharge, disassemble, heat above (manufacturer’s specified temperature rating), or incinerate. Doing so may result in injury due to venting, leakage, or explosion resulting in chemical burns.

• Ensure batteries are installed correctly according to polarity (+ and -).

• Do not mix old and new batteries, different brands, or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.

• Remove and immediately recycle or dispose of batteries from equipment not used for an extended time according to local regulations.

• Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

• Warning: contains coin battery

IC: 7666A-DTRAP

This device complies with Industry Canada RSS standard(s). Operation is subject to the following two conditions:

1. this device may not cause interference, and
2. this device must accept any interference, including interference that may cause undesired operation of the device.

www.bontrager.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>