TREK 2022 ROSCOE 7 Bike User Manual

TREK 2022 ROSCOE 7 Bike

2022 ROSCOE 7, 8, 9

Specifications

Chainline (1x only): 52-55

Chainring (1x only): 28T-34T

Rear brake mount: Minimum 160mm, direct mount;Maximum adaptable to 180mm

Maximum tire size: 29.0 x 2.60 (for 29″ wheel set) or 27.5 x 2.60 (for 27.5″ wheel set)

Seat post:

• Maximum insertion:
  • Extra small: 190mm
  • Small: 200mm
  • Medium: 240mm
  • Medium/large: 250mm
  • Large: 250mm
  • Extra large: 250mm
• Minimum insertion: 75mm*
• Seat tube inside diameter: 31.6mm
• Seat tube post clamp outer diameter: 36.2mm

Follow the seatpost manufacturer guidelines.

Safety

WARNING: Properly tighten hardware

Always tighten hardware to the specified torque. Over-tightening hardware could deform or break the hardware or components.
Under-tightening hardware could cause hardware or components to become loose. Either situation could damage the bicycle and result in injury to the rider.

WARNING: Reapply threadlocker

All reused-fasteners with pre-applied threadlocker must be cleaned with isopropyl alcohol and have new threadlocker applied before re-assembly. If threadlocker is not applied, the fasteners may loosen which could damage the bicycle and result in injury to the rider.

Derailleur Hanger

This bicycle frame is designed to use a Universal Derailleur Hanger (UDH). The thru axle must be compatible with a UDH and must be M12x1.0 with a 12.7mm thread. The washer is frame-specific.
Install only the washer compatible with your frame.

Tools:

• Thru axle — W600321
• Derailleur Hanger
• Washer — W600660
• Bolt

WARNING: Do not apply grease to the derailleur hanger or bolt. Apply grease to only the thru axle.

NOTICE: Do not over-tighten. Over-tightening the bolt could cause the hanger to break. For additional information about the UDH, refer to the SRAM user manual at www.sram.com.

Cabling

• Derailleur cable
• Rear brake hose
• Dropper post cable
• Zip tie guide for internal routing — W513977
• Plug cable guide — W5253075

Frame Guards

• Chainstay guard — W5252847
• Downtube guard — W5253074

Notice: Use isopropyl alcohol to clean the frame surface where the guard (2) attaches. Wait for the alcohol to dry before applying the guard. Do not clean the entire frame with isopropyl alcohol as it could damage the paint.

FAQ

Q: Can I use a different size chainring on my ROSCOE bike?
A: The ROSCOE bike is designed to work with chainrings ranging from 28T to 34T in size.

Q: What is the maximum tire size for the ROSCOE bike?
A: The maximum tire size for the ROSCOE bike is 29.0 x 2.60 for the 29″ wheel set or 27.5 x 2.60 for the 27.5″ wheel set. Please ensure there is sufficient clearance between the tire and the frame to avoid damaging the bicycle frame.

Q: How do I clean and apply frame guards on my ROSCOE bike?
A: To clean the frame surface where the guard attaches, use isopropyl alcohol. Wait for it to dry before applying the guard. However, do not clean the entire frame with isopropyl alcohol as it could damage the paint.

Safety

WARNING

• Properly tighten hardware
  Always tighten hardware to the specified torque.
  Over-tightening hardware could deform or break the  hardware or components. Under-tightening hardwarecould cause hardware or components to become loose.
  Either situation could damage the bicycle and result in injury to the rider.

• Reapply threadlocker
  All reused-fasteners with pre-applied threadlocker must be cleaned with isopropyl alcohol and have new threadlocker applied before re-assembly. If threadlocker is not applied, the fasteners may loosen which could damage the bicycle and result in injury to the rider.

Legend

Deraileur hanger

Tools

• 8mm hex tool
• Torque wrench (left-hand thread) with 8mm hex bit

WARNING
Do not apply grease to the derailleur hanger or bolt.
Apply grease to only the thru axle.

This bicycle frame is designed to use a Universal Derailleur Hanger (UDH).

NOTICE: The thru axle must be compatible with a UDH and must be M12x1.0 with a 12.7mm thread.

NOTICE: The washer is frame-specific. Install only the washer compatible with your frame.

NOTICE: Do not over-tighten. Over-tightening the bolt could cause the hanger to break.
For additional information about the UDH, refer to the SRAM user manual at www.sram.com.

Cabling

1. Derailleur cable
2. Rear brake hose
3. Dropper post cable
4. Zip tie guide for internal routing — W513977
5. Plug cable guide — W5253075
   • Zip tie

Zip tie guide

Tips:

• Before inserting the zip tie, bend it in half to create a crease. This will make it to easier wrap the zip tie around the cables and out through the hole.
• Use a hook tool and a pick tool to hold the cables and guide the zip tie around them.

Frame guards

1. Chainstay guard — W5252847
2. Downtube guard — W5253074
   • Zip tie

Downtube guard
Use isopropyl alcohol to clean the frame surface where the guard (2) attaches. Wait for the alcohol to dry before applying the guard.

Notice: Do not clean the entire frame with isopropyl alcohol. Isopropyl alcohol could damage the paint.

Specifications

Chainline (1x only)

Chainring (1x only)

Rear brake mount

Maximum tire size

Notice: Measurements of actual tires may vary. Always verify there is sufficient clearance between the tire and the frame. Improper tire size could damage the bicycle frame. Trek recommends 6mm clearance above and on the sides of the tire.

Seat post

WARNING
Always follow the seatpost manufacturer’s minimum insertion recommendation. Failure to follow the recommendation could cause damage to the seatpost and result in injury to the rider.

insertion

| Extra small| 190mm
Small| 200mm
Medium| 240mm
Medium/large
Large| 250mm
Extra large
2| Minimum insertion| 75mm*
3| Seat tube inside diameter| 31.6mm
 | Seat tube post clamp outer diameter| 36.2mm

Follow the seatpost manufacturer guidelines.

Bottom bracket / ISCG tabs

Suspension

The first step in suspension setup is to determine the sag. All other settings should be adjusted after determining the sag.
Refer to the suspension setup card included with your bike or the suspension calculator at Trekbikes.com/suspension-calculator.

Fork

WARNING
Exceeding the recommended maximum fork length could damage the bicycle and result in injury to the rider.

References

• SRAM

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>