novostella NTF91 Smart LED Flood Light User Guide

novostella NTF91 Smart LED Flood Light

Thank You

Thank you for ordering from Novostella. Set-up is easy and takes only a few minutes by following the instructions.

Part One – How to install the light?

Warning

1. Please check if the light and the parts are intact before installation.
2. Make sure to cut off power before installation.
3. Please do not place this light in corrosive conditions.
4. If there is any damage to the cord, please cut off the power and stop using it immediately.
5. Please do not retrofit the light within the warranty period.
6. To ensure the light works properly, please use the voltage indicated on the packing.

Parameters

Components

Note: Cord – type Y attachment.

For type Y attachment: If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer of his service agent or a similar qualified person in order to avoid a hazard.

Dimension

Components

Installation

Step A: According to the spacing of two screw bits on the bracket, drill two holes on the mounting panel.

Note: Maximum mounting height is over Sm.

Note:

1. Make sure that the distance between the light and the object being list imore than 1 meter, so as to avoid high temperature caused by short distance.

FCC ID: 2AWONNTF71

Federal Communication Commission(FCC)Statement for Users Warning:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation . This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

 Part Two – How to pair the light to Smart Life app?

Before starting the paring, please make sure to turn on the Bluetooth on your phone, and connect to the Internet.

Step A : Smart Life app installation

Please choose either way below to download and install the app.

1. As per your phone system, choose the QR code to scan.
   |
   ---|---
   iOS| Android
2. Search keyword ‘Smart Life’ in Apple Store of Google Play.

Step B : Create an account on Smart Life and login.

Note: Please keep your account and password in mind for Alexa or Google Assistant APP pairing later.

Step C : Add the light to Smart Life App

1. Tap’+’ button on top right corner to add devices. Tap ‘Lighting’, then choose ‘Light Source (BLE)’ to add the lights.
   

2. Power on the light with your own switch. Repeatedly turn on-off-on-offon- off-on switch to activate the light into rapid blinking status (about O.Ss per blink). Please make sure to keep an interval over 2 seconds between each turn-on and turn-off. Then click the ‘Next’ button on this page. Find the lighting devices and click’+’.
   

3. Give a name to the light.
   Note: A simple name is recommended.

4. The named light will be shown on the app homepage. Now you can control the light (turn on/off, change colors, adjust brightness ect .) with Smart Life on the setting page. Turn on or off the light by tapping the bulb icon .
   

How to group the lights?

Make sure all the lights have been paired to “Smart Life” app, then group the lights by following these steps.

Choose any light on the app, click the edit button on the top right corner, then click “Create Group” .

1. Choose the lights you want to group from the device list and rename the group.
   Now you can control the lights and sync with the music, the colors will be synchronized in the group.
   

Part Three – How to connect the lights to Internet, and control with

Amazon Alexa and Google Assistant?

If you want to connect the lights to Internet, and control with Amazon Alexa and Google Assistant, you can easily expand the smart flood lights with our Hub accessory (sold separately).

Please click below link to purchase the Hub accessory from our shop: https://www.amazon.com/dp/B08WXBLN3G

After you get the Hub accessory, please follow below steps to setup:

Step A: WiFi connection, pair the Hub to Smart Life App.

Please turn on the WiFi on your phone. The hub only supports 2.4GHz WiFi network, not 5.0GHz. Please make sure your working network is 2.4GHz and your router has disabled the MAC filter.

•• It is strongly recommended to place the hub to somewhere that is between the lighting devices and the router, and make sure it responds well to the WiFi signal.

1. Tap’+’ button on top right corner to add device. Tap ‘Gateway Control’, then choose ‘Wireless Gateway (BLE)’ to add the hub.
   

2. Plug the hub into a socket. Long press the power button on the hub till the indicator lights rapidly blink, tap the ‘Next’ button, then click ‘+’ button to add the hub.
   

3. Choose your WiFi network, enter your password, and tap the ‘Next’ button. Give a name to the hub and tap the ‘Done’ button.
   

Step B : Add the lights to the Hub.

Please make sure all the lights have been paired to ‘Smart Life’ App first. Choose the hub on the app, click the ‘add device by list’ button, select all the lights, and click the ‘Confirm’ button.

 How to control the light with Amazon Alexa?

Please make sure that your Alexa app is connected to Echo, and both work well under your WiFi network.

Step A : Log in your Alexa App, tap top left corner, and tap ‘Skills’ .

Step B : Type ‘Smart Life’, find ‘Smart Life’ from the search result and tap it to enable the skill,

Step C: Enter your Smart Life App account and password. Tap ‘Link Now’, then tap ‘Authorize’ on the next page to bind Smart Life account to Alexa .
Step D : When your Smart Life account is bound to Alexa, tap ‘DISCOVER DEVICES’ to detect the light.

Step E : When the named light is paired to Alexa from Smart Life, it will show on the device page (see the ‘smart light’ example ).

Step F : Now you can control the light with Alexa App on the setting page. To turn on or off the light, simply tap the bulb icon.

Step G : You can also voice control the light with Alexa by giving these commands: “Alexa, turn on ‘device name’ “, “Alexa, set ‘device name’ to ‘color ‘ “, “Alexa, set ‘device name’ to ‘number'”. Device name is the one you give to the light. The light is named ‘smart light’ in this user guide. For example, “Alexa, turn on ‘smart light'”, “Alexa, set ‘smart light’ to ‘blue'” etc.

 How To Control The Light With Google Assistant?

Step A : Login Google Assistant App, tap ‘Home Control’ on the left side bar page.
Step B : Tap’+’ button on the bottom right to enter next page.
Step C : Find ‘Smart Life’ from side bar list.

Step D : Enter your Smart Life App account and password to bind Smart Life account to Google Assistant.
Step E : You will find the named light shows on the Home Control page. Now you can control the light on Google Assistant App, or voice control it by giving these commands: “ok Google, turn on ‘device name'”, “ok Google, set ‘device name’ to ‘color’ “, “ok Google, set ‘device name’ to ‘number’ “.
Device name is the one you give to the light. The light is named ‘smart light’ in this user guide. For example, “ok Google, turn on ‘smart light'”, “ok Google, set ‘smart light’ to ‘blue’ ” etc.

Wireless Contro l Specification:
Wireless Frequency Range: 2.4-2.4835 GHz
Wireless Communications Protocol: BLE 5.0
Wireless Conducted Power: 7 dBm

Customer Support

E-manual

Step 1 : Scan the QR code
Step 2 : Click E-manual PDF file
Step 3 : Read file online or download
 Go paper-free, make life easier, and do something good for the environment.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>