novostella NTS32A LED RGB Light Strip User Guide

novostella NTS32A LED RGB Light Strip

THANK YOU for choosing Novostella. To optimize user experience, please use the product according to the following instructions.

Warning

1. Winding lighting is prohibited, as it affects heat dissipation and might cause dangers.
2. Please unroll the light strip from the plate before lighting it up.
3. This light strip can only work with ONE power adapter in a series con-nection of 32 meters maximally.
4. Please check if the light strip and the parts are intact before using them.
5. Please make sure that the power supply is turned off before installation.
6. Please use the attached power adapter only, to ensure that the light works properly.
7. Please do not use this light in the open air or under humid environment.

Specification

Components

LED Signal Receiver

RF Remote Controller

Three Settings
There are three flexible settings for the remote controller(s) to control the light strip(s) as per your lighting project, One-to-One Setting, One-to- Many Setting and Many-to-Many Setting. You can choose either which light strip and how many light strips one controller controls, or which controller and how many controllers control the light strip(s).

1. One-to-One Setting: One remote controller can only control one light strip. Turn on the remote controller and power on the LED Signal Receiver of the light strip. During the first 5 seconds, immediately long press the bottom left button on the remote controller till the strip light blinks. Then the ‘One-to-One Setting’ is done. One-to-One Setting is the factory default.
2. One-to-Many Setting: If you want to control many light strips with one remote controller, you could choose the ‘One-to-Many’Setting. Tum on the remote controller and power on all LED Signal Receivers of the light strips. During the first 5 seconds, immediately long press the bottom left button on the remote controller till the strip lights blink. Then the ‘One-to-Many Setting’ is done.
3. Many-to-Many Setting: If you have many light strips and remote controllers, and hope that any of the controller can control all the light strips, you could choose the ‘Many-to-Many’ Setting. Turn on each remote controller and power on its LED Signal Receiver. During the first 5 seconds, immediately long press the bottom right button on the remote controller till the strip light blinks.

Installation

How to cut the LED strip?
Before cutting the LED strip, please keep these in mind.

1. Once the strip is cut, an extra connector is needed for reconnection, otherwise the rest part being cut can not work. The connector is not included in the package. You may contact the seller for the connector details.
2. Double confirm the length for installation before making the cut.
3. Cut the strip along the marks.

How to install the LED strip?

Connect the light strip(Dto controller cable, and then connect controller cable to power adapter. Plug the adapter into the socket and turn on the light strip by pressing ‘ON’ button on the RF remote controller.

Note:

1. If the strip can’t light up after the installation, please check whether the joints are connected correctly.
2. Please make sure to turn off the power supply during routine maintenance.
3. To avoid any damage to the strip, please do not use chemical solvent during routine maintenance.

How to control the light strip?

• Download the App Lotus Lantern by scanning the QR code below. This App is compatible with Android 4.0 and iOS 8.1 or above.

• Power on the light.

• Activate the Bluetooth function on your phone and open the App to automatically connect to the light.

• Enjoy the lighting by exploring the functions such as brightness, modes, music sync, timer etc via the App.

Contact Us
Have some issue? No worries! Please reach us via these channels. Our customer services team is more than happy to help .

• [email protected]

• fb.com/novostella.jans

• Scan to Message Now

• www.novostella.net

• Manufacturer: Shenzhen Ustellar Technology Ltd.

• Address: Rm.201, A Bldg., No. A Qianhai 1st Rd., Shen’gang Cooperation Zone, Qianhai, Shenzhen, CHINA 518000

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>